The role of viscosity on drop impact forces on non-wetting surfaces

Vatsal Sanjay,Bin Zhang,Cunjing Lv,Detlef Lohse
2024-09-06
Abstract:A liquid drop impacting a rigid substrate undergoes deformation and spreading due to normal reaction forces, which are counteracted by surface tension. On a non-wetting substrate, the drop subsequently retracts and takes off. Our recent work (Zhang et al., \textit{Phys. Rev. Lett.}, vol. 129, 2022, 104501) revealed two peaks in the temporal evolution of the normal force $F(t)$ -- one at impact and another at jump-off. The second peak coincides with a Worthington jet formation, which vanishes at high viscosities due to increased viscous dissipation affecting flow focusing. In this article, using experiments, direct numerical simulations, and scaling arguments, we characterize both the peak amplitude $F_1$ at impact and the one at take off ($F_2$) and elucidate their dependency on the control parameters: the Weber number $We$ (dimensionless impact kinetic energy) and the Ohnesorge number $Oh$ (dimensionless viscosity). The first peak amplitude $F_1$ and the time $t_1$ to reach it depend on inertial timescales for low viscosity liquids, remaining nearly constant for viscosities up to 100 times that of water. For high viscosity liquids, we balance the rate of change in kinetic energy with viscous dissipation to obtain new scaling laws: $F_1/F_\rho \sim \sqrt{Oh}$ and $t_1/\tau_\rho \sim 1/\sqrt{Oh}$, where $F_\rho$ and $\tau_\rho$ are the inertial force and time scales, respectively, which are consistent with our data. The time $t_2$ at which the amplitude $F_2$ appears is set by the inertio-capillary timescale $\tau_\gamma$, independent of both the viscosity and the impact velocity of the drop. However, these properties dictate the magnitude of this amplitude.
Fluid Dynamics,Soft Condensed Matter
What problem does this paper attempt to address?
The problem that this paper attempts to solve is to explore the influence of viscosity on the impact force during the impact process of droplets on non - wetting surfaces. Specifically, the research focuses on a series of deformation and spreading processes that droplets experience when they impact on a rigid substrate. These processes are counteracted by the normal reaction force of the substrate and are also affected by surface tension. For non - wetting surfaces, droplets will bounce back after retraction. The research found that there are two peaks in the time evolution of the normal force \(F(t)\) when droplets impact and jump off. The second peak coincides with the formation of the Worthington jet, but it will disappear at high viscosities due to the increase in viscous dissipation. In this paper, through experiments, direct numerical simulations and scaling analysis, these two peak amplitudes \(F_1\) and \(F_2\) are characterized, and their dependence on the control parameters - the Weber number \(\text{We}\) (dimensionless kinetic energy) and the Ohnesorge number \(\text{Oh}\) (dimensionless viscosity) is elucidated. ### Main research contents 1. **Impact at low Ohnesorge numbers (\(\text{Oh}\ll1\))**: - For low \(\text{Oh}\) and large \(\text{We}\), the inertial force and time scale determine the dynamics of droplet impact. - The amplitude of the first peak \(F_1\) is proportional to the inertial pressure force \(F_\rho=\rho_d V_0^2 D_0^2\), that is, \(F_1\sim F_\rho\). - The time \(t_1\) to reach the first peak is proportional to the inertial time scale \(\tau_\rho = \frac{D_0}{V_0}\), that is, \(t_1\sim\tau_\rho\). 2. **Impact at high Ohnesorge numbers (\(\text{Oh}\gg1\))**: - As \(\text{Oh}\) increases, the normalized value of the amplitude of the first impact force peak \(F_1\) begins to increase, indicating that viscosity begins to play an important role near \(\text{Oh}\approx0.1\). - At high \(\text{Oh}\), the observed scaling relationship is \(F_1\sim F_\rho\sqrt{\text{Oh}}\). - The time \(t_1\) to reach the first peak is proportional to \(\tau_\rho\sqrt{\text{Oh}}\), that is, \(t_1\sim\tau_\rho\sqrt{\text{Oh}}\). 3. **Second peak \(F_2\)**: - The time \(t_2\) when the second peak \(F_2\) appears is determined by the inertial - capillary time scale \(\tau_\gamma=\sqrt{\frac{\rho_d D_0^3}{\gamma}}\), and is independent of viscosity and impact velocity. - But these properties determine the amplitude of this peak. ### Key formulas - Weber number \(\text{We}\): \[ \text{We}=\frac{\rho_d V_0^2 D_0}{\gamma} \] - Ohnesorge number \(\text{Oh}\): \[ \text{Oh}=\frac{\eta_d\sqrt{\rho_d\gamma}}{D_0} \] - Inertial force scale \(F_\rho\): \[ F_\rho = \rho_d V_0^2 D_0^2 \] - Inertial time scale \(\tau_\rho\): \[ \tau_\rho=\frac{D_0}{V_0} \] - Inertial - capillary time scale \(\tau_\gamma\): \[ \tau_\gamma=\sqrt{\frac{\rho_d D_0^3}{\gamma}} \]