Abstract:Ultrasonic cavitation is the formation of vapour cavities within a liquid due to the action of an ultrasound source. It is widely used for homogenization, dispersion, deagglomeration, erosion, cleaning, milling, emulsification, extraction, disintegration and sonochemistry. On the other hand, the so-called cavitation number is used to assess the likelihood of cavitation in fluid flows within a conduit or around a hydrofoil but it is not valid in ultrasonic cavitation since there is no fluid flow. A recently formulated number predicts the cavitation in case of sudden accelerations. The tip surface of an ultrasonic probe is subjected to a continuous repetition of alternating accelerations at high frequency. Therefore, the use of the recently formulated number in ultrasonic cavitation is explored here. Simulations of the ultrasonic probe in water just at the condition of cavitation onset have been performed for a combination of probe diameters from 0.2 to 100 mm and frequencies 20, 30, 40, 100 and 1000 KHz. The recently formulated number is applied to these combinations and it is found that can be used to predict ultrasonic cavitation. Consequently, the dimensionless number can be used to decide the conditions to avoid or generate cavitation when a fluid is sonicated and to increase reproducibility in such conditions.

What problem does this paper attempt to address?

The paper primarily focuses on addressing the reproducibility issue of ultrasonic cavitation in experiments. The authors propose and apply a new dimensionless number to predict whether ultrasonic cavitation will occur under given conditions. Specifically, the problems addressed in the paper include: 1. **Limitations of traditional cavitation number**: The traditional cavitation number used to assess the likelihood of cavitation in fluid flow is not applicable to ultrasonic cavitation, as there is no fluid flow in ultrasonic cavitation. 2. **Control and prediction of ultrasonic cavitation**: Currently, the method to control the intensity of ultrasonic cavitation is usually by adjusting the power output and frequency of the ultrasonic probe, but this does not accurately predict whether cavitation will occur. 3. **Reproducibility of experimental results**: Due to slight differences in experimental conditions (such as container geometry, power, and frequency), even experiments conducted under the same settings may result in significant deviations. To address the above issues, the authors propose a new dimensionless number \(G_A\) and validate its effectiveness through numerical simulations. This dimensionless number can accurately predict the threshold for the occurrence of ultrasonic cavitation, especially under conditions close to the cavitation threshold, which helps improve the reproducibility and accuracy of experimental results. Additionally, the paper compares the applicability of the traditional cavitation number and the newly proposed \(G_A\), pointing out that in many common application scenarios, using \(G_A\) can better predict the occurrence of ultrasonic cavitation, thereby increasing the reliability of experimental results.

Prediction of ultrasonic cavitation with a dimensionless number, towards higher reproducibility

The Relationship of Cavitation to the Negative Acoustic Pressure Amplitude in Ultrasonic Therapy

Characterization of cavitation under ultrasonic horn tip - Proposition of an acoustic cavitation parameter

Identification approach of acoustic cavitation via frequency spectrum of sound pressure wave signals in numerical simulation

Numerical Simulation of Cavitation Flow under High Pressure and Temperature

Towards a general description of the cavitation threshold in acoustic systems

Numerical prediction of cavitation nuisance on hydrofoils: Combined analysis of cavity dynamics and the aggressiveness of collapsing cavitating structures

Numerical Simulation of Cavitation-Erosion on a Plane-Convex Hydrofoil Using a Homogeneous Mixture Assumption

Numerical Simulation of Cavitation Erosion on A Naca0015 Hydrofoil Based on Bubble Collapse Strength

Numerical Prediction of Cavitation for a Horizontal Axis Tidal Turbine

Numerical Investigation on the Hydrodynamic Performance with Special Emphasis on the Cavitation Intensity Detection in a Venturi Cavitator

Acoustic measurements of the nucleus size distribution at the cavitation threshold

Study on the Characterization Method of Ultrasonic Cavitation Field Based on the Numerical Simulation of the Amplitude of Sound Pressure

Numerical investigations on effects of cavitation number on hydrodynamic performance of centrifugal pump

Numerical Prediction Of The Hydrodynamic Performance Of A Centrifugal Pump In Cavitating Flows

Numerical analysis of cavitation-induced noise characteristics in hydrofoils using finite element acoustic method and spherical cavity radiation theory

Numerical prediction of impact force in cavitating flows

Numerical Simulation of Cavitation Characteristic Around Hydrofoil NACA0015

Numerical Method for Three-dimensional Cavitation Flows at Small Cavitation Numbers

Numerical Investigation of Unsteady Cavitation Around a NACA 66 Hydrofoil Using OpenFOAM

Dual frequency Ultrasonic Cavitation in Various Liquids: High-Speed Imaging and Acoustic Pressure Measurements