Abstract:Abstract Scale-up studies of fluidized beds are important for numerous fields. Fluidization in a multi-ring inclined nozzle spout-fluid bed (MRIN spout-fluid bed) is one of the most critical factors that affect the coating efficiency and uniformity of tri-structural isotropic (TRISO) nuclear particles in the fluidized bed chemical vapor deposition (FB-CVD) process. In this work, the flow pattern similarity principle was proposed to scale up a specially designed spout-fluid bed, which was aimed at maintaining the gas-solid contact efficiency, and was validated by electrical capacitance tomography (ECT) measurements. First, the traditional ECT method was developed for the specially designed MRIN spout-fluid bed according to the filling method. Then, the reconstruction algorithms were updated using the alternating direction multiplier method (ADMM) by introducing optimization constraints. The fluidization laws were investigated for different superficial gas velocities and distributor structures. We found that the gas distributor structure affected the merge point of the jets, which played an essential role in fluidization pattern changes. The statistically-based coefficient of variation (Cv) was proposed to distinguish the different flow patterns. Multi-ring spouting was then selected as a typical flow pattern for good fluidization and mixing, where the Cv ranged from 0.25 to 0.65. Then, the optimal design principles for the enlarged spout-fluid bed gas distributor were obtained. We determined that a smaller nozzle diameter (0.71 d 0 ), larger nozzle spacing (1.12 x 0 ), and slightly inclined angle (1.50 θ 0 ) could improve fluidization, and that nozzle spacing was the most important factor. This study may be beneficial for the industrial design of the FB-CVD process and for the fabrication of high-density nuclear fuel particles. Additionally, it could be presented to a more general audience for scaling-up fluidized beds with a complex distributor, which would be beneficial for the fluidization research community.

Scale-up of Dry Impregnation Processes for Porous Spherical Catalyst Particles in a Rotating Drum: Experiments and Simulations

Scale-up of dry impregnation processes for porous spherical catalyst particles in a rotating drum: experiments and simulations

Multi-Scale Coupling Model Involving Bed and Catalyst Particle for MTP Reactor Simulation

The Hydrodynamics of Low-Density Particles and Optimization of the EMMS Calculation Process

Effect Of The Scale-Up Process On The Reactor Performance Within The Riser: Simulation Using Ozone Decomposition

Performance Evaluation and Scale-up of the Swirl-Venturi Microdroplet Generator

The Effects of Processing Parameters on the Properties of Micro-Scale Porous Surface for a Micro-Channel Reactor

Performance Evaluation and Scale-Up Behavior of an Engineered In-Line Mixer for 3D Printing

Numerical analysis of residence time for particle impregnation in a rotating drum

Discrete Element Simulations and Machine Learning for Improving the Performance of Dry Catalyst Continuous Impregnation Processes

Trans-level multi-scale simulation of porous catalytic systems: Bridging reaction kinetics and reactor performance

Development of Centrifugal Coating Device to Load CuZnZr/γ-Al2O3 Catalyst on Porous Substrates for Methanol Steam Reforming

Strategy for Scaling‐up of a Microsieve Dispersion Reactor

Structural optimization of 3D printed SiC scaffold with gradient pore size distribution as catalyst support for methanol steam reforming

MASS TRANSFER MODEL FOR CATALYST CAPSULE IN CATALYTIC DISTILLATION (II) MENSURATION AND CALCULATION OF EFFECTIVENESS FACTOR

Scale-Up of a Heterogeneous Photocatalytic Degradation Using a Photochemical Rotor-Stator Spinning Disk Reactor

Modeling Study of Gas-Liquid Mass Transfer Enhancement by Cylindrical Catalyst Particles

Design and Scale up of a Mixing Process for a Novel Automotive Coating

Influencing Factors on the Wet Impregnation of Additive‐Manufactured Catalyst Support Structures

Experimental study on the scale-up of a multi-ring inclined nozzle spout-fluid bed by electrical capacitance tomography

Heat and water transfer in a rotating drum containing solid substrate particles