Abstract:Understanding interfacial mass transfer during dissolution of gas in a liquid is vital for optimising large-scale carbon capture and storage operations. While the dissolution of CO2 bubbles in reservoir brine is a crucial mechanism towards safe CO2 storage, it is a process that occurs at the pore-scale and is not yet fully understood. Direct numerical simulation (DNS) models describing this type of dissolution exist and have been validated with semi-analytical models on simple cases like a rising bubble in a liquid column. However, DNS models have not been experimentally validated for more complicated scenarios such as dissolution of trapped CO2 bubbles in pore geometries where there are few experimental datasets. In this work we present an experimental and numerical study of trapping and dissolution of CO2 bubbles in 3D printed micromodel geometries. We use 3D printing technology to generate three different geometries, a single cavity geometry, a triple cavity geometry and a multiple channel geometry. In order to investigate the repeatability of the trapping and dissolution experimental results, each geometry is printed three times and three identical experiments are performed for each geometry. The experiments are performed at low capillary number representative of flow during CO2 storage applications. DNS simulations are then performed and compared with the experimental results. Our results show experimental reproducibility and consistency in terms of CO2 trapping and the CO2 dissolution process. At such low capillary number, our numerical simulator cannot model the process accurately due to parasitic currents and the strong time step constraints associated with capillary waves. However, we show that, for the single and triple cavity geometry.

What problem does this paper attempt to address?

The problem that this paper attempts to solve is the accurate prediction of the carbon dioxide (CO₂) dissolution process in porous media, especially the dissolution mechanism in geological carbon capture and storage applications. Specifically, the research focuses on the capture and dissolution processes of CO₂ bubbles in 3D - printed micromodel geometries. There are two main objectives of the paper: 1. **Generate reproducible 3D - printed microfluidic devices**: Generate microfluidic devices with three different geometries through 3D - printing technology to achieve the reproducibility of the CO₂ bubble capture and dissolution processes and generate a benchmark data set. 2. **Verify the existing direct numerical simulation (DNS) model**: Verify whether the existing direct numerical simulation model can accurately capture the dissolution rate of CO₂ bubbles in 3D - printed micromodels through experimental results. ### Research Background - **Carbon Capture and Storage (CCS)**: Large - scale carbon capture and storage operations require the optimization of the gas dissolution process in liquids, especially the dissolution of CO₂ in reservoir brines, which is a key mechanism for achieving safe CO₂ storage. - **Limitations of Numerical Simulation**: Although there are already direct numerical simulation (DNS) models that describe this dissolution process and have been verified by semi - analytical models in simple cases (such as rising bubbles in a liquid column), these models have not been experimentally verified in more complex scenarios (such as trapped CO₂ bubbles in porous media). - **Advantages of 3D Printing**: 3D - printing technology can generate standardized and reproducible micromodel geometries, allowing researchers to control the geometry of porous media and thus precisely study the influence of pore structures on fluid flow. ### Experimental Methods - **Micromodel Design**: Three different micromodel geometries were designed using OpenSCAD software: - Single Cavity Geometry (SC) - Triple Cavity Geometry (TC) - Multiple Channels Geometry (MC) - **3D Printing**: Use the Formlabs Form 2 stereolithography (SLA) printer to generate micromodels. - **Experimental Setup**: The experimental setup includes an injection pump, a pressure regulator, a high - resolution camera, etc., which are used to inject CO₂ and water and record the capture and dissolution processes of CO₂ bubbles. - **Image Processing**: Use MATLAB to post - process the experimental images and extract the volume change of CO₂ bubbles. ### Numerical Simulation - **Volume - of - Fluid (VOF) Method**: Use the VOF method to simulate two - phase flow, where the interface is represented by an indicator function. - **Mass Transfer**: Simulate the mass transfer at the interface through the Continuous Species Transfer (CST) method. - **Simulation Parameters**: Dimensionless numbers such as the Reynolds number (Re), the Péclet number (Pe), and the Capillary number (Ca) are considered in the simulation to characterize the characteristics of fluid flow. ### Main Findings - **Experimental Reproducibility**: The experimental results show that the CO₂ bubble capture and dissolution processes in 3D - printed micromodels have good reproducibility. - **Accuracy of Numerical Simulation**: For the single - cavity and triple - cavity geometries, the numerical simulation can better capture the experimental results, but in the multi - channel geometry, due to the influence of surface tension, there is a large deviation between the numerical simulation results and the experimental results. ### Conclusion This research successfully verified the capture and dissolution processes of CO₂ bubbles in porous media through 3D - printed micromodels and numerical simulation, providing valuable experimental data and a basis for numerical model verification for future research.

Experimental investigation of solubility trapping in 3D printed micromodels

Benchmarking the Viability of 3D Printed Micromodels for Single Phase Flow Using Particle Image Velocimetry and Direct Numerical Simulations

Simulations of CO2 Dissolution in Porous Media Using the Volume-of-Fluid Method

Investigations in Geologic Carbon Sequestration: Multiphase Flow of CO 2 and Water in Reservoir Rocks

Pore-scale Visualization Study on CO2 Displacement of Brine in Micromodels with Circular and Square Cross Sections

Pore Scale Study of Multiphase Multicomponent Reactive Transport During CO2 Dissolution Trapping

Dissolution Trapping of Carbon Dioxide in Heterogeneous Aquifers

Using Direct Numerical Simulation of Pore-Level Events to Improve Pore-Network Models for Prediction of Residual Trapping of CO2

Simplified Numeric Simulation Approach for CO$_{2,g}$-Water Flow and Trapping at Near-Surface Conditions

Inertial Effects during the Process of Supercritical CO2 Displacing Brine in a Sandstone: Lattice Boltzmann Simulations based on the Continuum‐surface‐force and Geometrical Wetting Models

Pore-scale modeling on supercritical CO2 invasion in 3D micromodel with randomly arranged spherical cross-sections

Modeling of ex-situ dissolution for geologic sequestration of carbon dioxide in aquifers

Impact of Wettability on CO2 Dynamic Dissolution in Three-Dimensional Porous Media: Pore-Scale Simulation Using the Lattice Boltzmann Method

Effective Constitutive Relations for Simulating CO2 Capillary Trapping in Heterogeneous Reservoirs with Fluvial Sedimentary Architecture

Pore-scale Mass Transfer Experiments in Porous Media by X-ray CT Scanning☆

Numerical Simulation of Carbon Dioxide–Nitrogen Mixture Dissolution in Water-Saturated Porous Media: Considering Cross-Diffusion Effects

Simulation of the Microscopic Seepage Process of CO 2 Storage in Saline Aquifers at the Pore Scale

Simulation of CO2 Storage using a Parameterization Method for Essential Trapping Physics: FluidFlower Benchmark Study

Numerical Study of the Effects of Permeability Heterogeneity on Density-Driven Convective Mixing During CO2 Dissolution Storage

Diffusive and convective dissolution of carbon dioxide in a vertical cylindrical cell

Multiscale Simulation of Water/oil Displacement with Dissolved CO2: Implications for Geological Carbon Storage and CO2-enhanced Oil Recovery