Abstract:TiC bonded diamond composites were prepared from a mixture of Ti, graphite, and diamond powders as raw materials, with Si as sintering additives, through high-temperature and high-pressure (HTHP) technology. The reaction between Ti and graphite under 4.5–5 GPa pressure and 1.7–2.3 kW output power can produce TiC as the main phase. The diamond particles are surrounded by TiC, and the interface is firmly bonded. The coefficient of friction (COF) of TiC–diamond composites with POM and PP balls decreases with increasing load for a specific friction velocity. However, the COF of TiC–diamond composites with agate, Cu and Al balls increases with the rising load because of the enhanced adhesive wear effect. The COF of PP, Cu and Al balls slightly increases with the increase in friction velocity at a certain load. SEM results show that the surface of agate balls has rough, pear-shaped grooves and shallow scratches. The scratches on the surface of POM balls are wrinkled. The PP balls have pear-shaped groove scratches on their wear surfaces. The wear mechanism of TiC–diamond composites with Cu ball pairs is primarily adhesive wear. The abrasion of TiC–diamond composites with Cu ball pairs remains almost unchanged as the load increases. However, the depth and width of the pear-shaped grooves on the wear surface of TiC–diamond composites are significantly increased. This phenomenon may be attributed to the high rotational speed, which helps to remove the residual abrasive debris from the friction grooves. As a result, there is a decrease in both the depth and width of the pear-shaped grooves, leading to a smoother overall surface. The wear mechanism of TiC–diamond composites with Al ball pairs is abrasive wear, which increases with an increasing load. When the load is constant, as the speed increases, the wear morphology of TiC–diamond composites with Al ball pairs transitions from rough to smooth and then back to rough again. This phenomenon may be attributed to the wear mechanism at low speeds being groove wear and adhesive wear. As the speed increases, the wear particles are more easily removed from the wear track, leading to a reduction in abrasiveness. As the speed increases, the wear surface becomes roughened by a combination of grooves and dispersed wear debris. This can be attributed to the increased dynamic interaction between surfaces caused by higher speed, resulting in a combination of abrasive and adhesive wear. In addition, Cu and Al ball wear debris appeared as irregular particles that permeated and adhered to the surface of the TiC phase among the diamond particles. The results suggest that TiC–diamond composites are a very promising friction material.

Effects of Oxidation on the Tribological Properties of Diamond Sliding Against Silica. Insights from Ab initio Molecular Dynamics

Nanotribological Properties of Oxidized Diamond/Silica Interfaces: Insights into the Atomistic Mechanisms of Wear and Friction by Ab Initio Molecular Dynamics Simulations

Ab initio insights into the interaction mechanisms between H$_2$, H$_2$O, and O$_2$ molecules with diamond surfaces

Friction and Wear Studies of Octadecyltrichlorosilane SAM on Silicon

Atomistic Wear Mechanisms in Diamond: Effects of Surface Orientation, Stress, and Interaction with Adsorbed Molecules

Adhesion, Friction and Tribochemical Reactions at the Diamond-Silica Interface

Lubrication and Anti-Wear Behavior of Duplex Annealed Nanodiamonds/peo Coating on Ti6Al4V: Functional Mechanism of Structural Transformation

Oxygen-terminated diamond: insights into the correlation between surface oxygen configurations and work function values

Insights into the surface oxidation modification mechanism of nano-diamond: An atomistic understanding from ReaxFF simulations

Effects Of Atomic Oxygen Exposure On Tribological Property Of Zirconium Alloy

Effects of Vapor Environment and Counter-Surface Chemistry on Tribochemical Wear of Silicon Wafers

XPS analysis of molecular contamination and sp2 amorphous carbon on oxidized (100) diamond

Different tribological behaviors of titanium alloys modified by thermal oxidation and spraying diamond like carbon

Tribological Behavior of Diamond Like Carbon Film Sliding Against Cocrmo or Al2o3 in Air and Water Environment

In Situ Synthesis and Tribological Characterization of TiC–Diamond Composites: Effect of the Counterface Material on Wear Rate and Mechanism

Research on Atomic Oxygen Erosion Influence of Structural Damage and Tribological Properties of Mo/MoS2-Pb-PbS Thin Film

An experimental investigation of adhesive wear extension in fretting interface: application of the contact oxygenation concept

The effect of oxygen introduced by WO3 on the structure and tribological performance of W-S-O sputtered films

Atomic Insight into Tribochemical Wear Mechanism of Silicon at the Si/SiO2 Interface in Aqueous Environment: Molecular Dynamics Simulations Using ReaxFF Reactive Force Field

Effects of structure relaxation and surface oxidation on nanoscopic wear behaviors of metallic glass

Tribochemical Mechanism of Amorphous Silica Asperities in Aqueous Environment: a Reactive Molecular Dynamics Study.