Optimization of a Commercial Injection-Moulded component by Using DOE and Simulation

Mandana Kariminejad,David Tormey,Saif Huq,Jim Morrison,Jeff Redmond,Carlos Souto,Marion McAfee

DOI: https://doi.org/10.48550/arXiv.2301.11620

2023-01-27

Abstract:Injection moulding is an important industry, providing a significant percentage of the demand for plastic products throughout the world. The process consists of many variables which directly or indirectly influence the part quality and cycle time. The first step in optimizing the process parameters is identifying the most significant variables affecting the desired output. For this purpose, various Design of Experiments methods (DOE) have been developed to investigate the effect of the experimental variables on the output and predict the required settings to achieve the optimal value of the output. In this study we investigate the application of DOE for a commercial injection moulded component which suffers from a long cycle time and high shrinkage. The Taguchi method has been used to analyze the effect of four input variables on the two output variables: cycle time and shrinkage. The component has been simulated in the Moldflow software to validate the predicted output and optimized settings of the variables from the DOE. A comparison of the simulation result and the predicted value from the DOE illustrated good accordance. The calculated optimal setting with the Taguchi method reduced the cycle time from the 40s to about 23s and met the shrinkage criteria for this commercial part.

Systems and Control

What problem does this paper attempt to address?

The problem that this paper attempts to solve is to optimize the production process of commercial injection - molded components in order to reduce their excessive cycle time and high shrinkage rate. Specifically, the research aims to determine the key variables affecting the injection - molding process and find the optimal settings of these variables by using the Design of Experiments (DOE) method and simulation techniques, thereby improving product quality and production efficiency.

### Problem Background
Injection molding is an important industrial production method and is widely used in the manufacturing of plastic products. However, this process involves many variables that directly or indirectly affect the product quality and production cycle. Non - optimal process settings will not only lead to product defects (such as warping, shrinkage and residual stress), but also result in a longer cycle time and an inefficient production process.

### Solution
To solve the above problems, the author adopted the following methods:

1. **Taguchi Method**: This is an experimental design method. By designing experiments with orthogonal arrays, it can effectively screen out the input variables that have a significant impact on the output with a relatively small number of experiments and optimize the settings of these variables.
2. **Moldflow Simulation Software**: It is used to simulate the injection - molding process and verify the output results predicted by the Taguchi method and the optimized variable settings. This can not only save the time and cost of actual experiments, but also ensure the consistency between the simulation results and the actual process.

### Research Content
This research mainly explored the influence of four input variables (melt temperature, mold temperature, injection pressure and holding pressure time) on two key output variables (cycle time and shrinkage rate). The experiment was designed by using the L9 orthogonal array, and the Moldflow software was used for simulation. Finally, the optimal process parameter settings were found.

### Main Findings
- **Mold Temperature** is the most important factor affecting cycle time and shrinkage rate. Setting the mold temperature to the highest level (85°C) can significantly reduce the cycle time and shrinkage rate.
- The optimal process parameter settings are as follows:
- Mold Temperature: 85°C
- Melt Temperature: 215°C
- Injection Pressure: 53 MPa (for cycle time) or 47 MPa (for shrinkage rate)
- Holding Pressure Time: 3.5 seconds (for cycle time) or 4.5 seconds (for shrinkage rate)

Through these optimized settings, the cycle time is reduced from about 40 seconds to about 23 seconds, and the shrinkage rate also meets the expected standard, ensuring that excessive shrinkage will not occur.

### Conclusion
This research has successfully applied the Taguchi method and Moldflow simulation to optimize the key parameters in the injection - molding process, significantly improving production efficiency and product quality. Future research can further verify these simulation data and increase the number of experiments to study the interaction between various factors.