Abstract:In this paper, we present a detailed experimental and numerical study of the flow phenomena and the heat transfer in swirl tubes with one and multiple tangential inlet jets. Such tangential jets induce a highly 3D swirling flow and an enhanced turbulence in the tube, increasing the convective heat transfer. Thus, a swirl tube is considered as an effective cooling method for technical applications with high thermal loaded components like gas turbine blades. The flow field, the heat transfer and the pressure loss are examined in a swirl tube with three different inlet jet configurations with one (MI1), three (MI3) or five (MI5) tangential inlet jets in axial direction. For this purpose, we measured the flow field via stereo-PIV (Particle Image Velocimetry) and the heat transfer by applying a transient technique using thermochromic liquid crystals for several Reynolds numbers. The numerical simulations are performed via Detached Eddy Simulation. The PIV results reveal a complex axial velocity changing after each inlet due to the additional mass flow. Two main structures occur in the swirl tube with five inlet jets: a vortex in the tube center in a wave-like form and large spiral vortices around the tube axis especially near the inlet jets. In the inlet region(s) the highest heat transfer occurs and decreases continuously until the next inlet or towards the tube outlet for the swirl tube with one inlet. The swirl tubes with multiple inlets show lower maximum heat transfer rates compared to the swirl tube with only one inlet due to lower inlet jet velocities. However, the heat transfer distribution is more homogeneous over the entire tube length at a much lower pressure loss. The homogeneous heat transfer can be explained by two mechanisms. At the inlets, the tangential jets impinge onto the concave wall and cause an enhanced convective heat transfer correlating with large spiral vortices. Secondly, the axial velocity becomes stronger further downstream after each inlet jet and causes an enhanced heat transfer between the inlet jets. The thermal performance parameter for all investigated swirl tube configurations is in the same order of magnitude. Thus, all swirl tube configurations are suitable for cooling. If one is interested in a maximum heat transfer paid by a high pressure loss, the swirl tube with one inlet is the best choice. If a lower but more homogeneous heat transfer with a low pressure loss is desired, one should choose the swirl tube with multiple inlets.

Effect of Flow Swirling on the Subsonic Air Jet in the VGU-4 HF Plasmatron

Numerical Simulation of Heat Transfer and Fluid Flow of a Non-Equilibrium Argon Plasma Jet with Confined Wall

Effects of Swirling Flow on the Heat Transfer and Flow in a Thermal Plasma Reactor

Numerical Simulation for Effects of Venturi Tube on Swirling Flow Field

Investigation of plasma swirl dynamics and effects of secondary gas injection in a vortex gas stabilized DC arc plasma

Analysis of the three-dimensional swirling and non-swirling jet impingement using a turbulence model with cross-diffusion correction

Investigation of the Swirl Flow on Anode Surface in High-Current Vacuum Arcs

Quasi-direct numerical simulations of the flow characteristics of a thermal plasma reactor with counterflow jet

Effects of the Swirling Coolant Jet from the Upstream Slot on the Vane Endwall Cooling and the Vane Suction Side Phantom Cooling

Visualization of arc and plasma flow patterns for advanced material processing

DNS Study of Swirling Intensity Effect on Flow Pattern of a Circular Jet

Numerical simulation of buoyant flow in a vertical channel for a plasma-facing component

A numerical model of plasma effects in flow control

Flowfield induced by a plasma synthetic jet actuator with low exit inclination angle under low ambient pressure

Numerical Investigations on the Aerothermal Performance and Film Cooling Effectiveness of Turbine Vane Endwall at Inlet Swirl Conditions

Flow and Heat Transfer Measurements in Swirl Tubes with One and Multiple Tangential Inlet Jets for Internal Gas Turbine Blade Cooling

Linear analysis of a swirling jet with a realistic swirler model

Experimental study of swirling flow characteristics in a semi cylinder vortex cooling configuration

Large-Eddy Simulation Study of Flow and Heat Transfer in Swirling and Non-Swirling Impinging Jets on a Semi-Cylinder Concave Target

Numerical study of discharge characteristics of an atmospheric pressure plasma jet with a coaxial dual-channel inlet

Effect Of Inlet Swirl On The Model Leading Edge Of Turbine Vane