General friction law for velocity‐stress dependent phase transition in granular flow

Yang Wang,Wei Wu,T. Matthew Evans,Huanran Wu,Yang Xiao

DOI: https://doi.org/10.1002/nag.3355

IF: 4

2022-03-06

International Journal for Numerical and Analytical Methods in Geomechanics

Abstract:International Journal for Numerical and Analytical Methods in Geomechanics, EarlyView.

mechanics,materials science, multidisciplinary,engineering, geological

What problem does this paper attempt to address?

Numerical Simulations of Granular Material Behavior under Rotation of Principal Stresses: Micromechanical Observation and Energy Consideration

Q. X. Wu,Z. X. Yang,X. Li

DOI: https://doi.org/10.1007/s11012-018-00939-4

IF: 2.7

2019-01-01

Meccanica

Abstract:A numerical investigation on the behavior of granular materials subjected to the rotation of principal stresses using the discrete element method is presented. A numerical procedure is developed to implement the two-dimensional arbitrary stress or strain paths imposed on polygonal specimens. Significant volumetric strain can be obtained and granular assembly appears to develop an anisotropic internal structure characterized by the contact-normal-based fabric tensor in due course, with its direction being rotated with the rotation of the principal stress. The observations indicate a significant degree of non-coaxiality between the principal-stress direction and the principal-strain increment direction. An ultimate state can be reached after sufficiently large numbers of cycling, resulting in a constant fabric norm and a circular strain trajectory in the deviatoric space. The boundary work, dissipation, and strain energy, are also registered during the entire loading process and its correlation between non-coaxial deformations is analyzed from micro-scale perspective. Before the ultimate state is reached, the applied work is partially dissipated by frictional sliding, and the remainder is stored as the strain energy within the specimen. When the ultimate state is reached, however, no change in the strain energy is obtained, and the plastic work is entirely dissipated, as the elastic portion of the free energy increment only depends on the elastic strain.
Local Fluctuations and Spatial Correlations in Granular Flows under Constant-Volume Quasistatic Shear.

Ning Guo,Jidong Zhao

DOI: https://doi.org/10.1103/physreve.89.042208

2014-01-01

Abstract:We investigate the local fluctuations in dense granular media subjected to athermal, quasistatic shearing, based on three-dimensional discrete element method simulations. By shearing granular assemblies of different polydispersities under constant-volume constraint, we quantify the characteristics of local structures (in terms of local volume and local anisotropy) and local deformation (using local shear strain and nonaffine displacement). The distribution of the local volume in a granular medium is found unchanged during the entire shearing process, which indicates a constant temperaturelike compactivity for the material. The compactivity is not, however, equilibrated among different particle groups in a polydisperse assembly. The local structures of a disordered granular assembly are inherently anisotropic. The fluctuations in local anisotropy can be well captured by a gamma or mixed-gamma distribution function, which is also unchanged during the shear. The local anisotropic orientation evolves towards the coaxial direction of the stress anisotropy with shear. The deformation characteristics of a jammed granular medium have their origins in the structural amorphousness. The local shear strain field depicts clear shear transformation zones which act as plasticity carriers. The spatial correlation of the local shear strains exhibits a fourfold pattern which is stronger in the stress deviatoric planes than in the stress isotropic plane. The fluctuations of nonaffine displacement suggest an isotropic granular temperature and an isotropic spatial correlation independent of the stress state. Both the local strain and the nonaffine displacement exhibit a power-law decayed distribution with a long-range correlation. We further modify the shear-transformation-zone theory to predict the pressure-dependent constitutive behavior of a sheared granular material and compare its prediction with our simulation data.
Constitutive Model for Granular-Fluid Flows Based on Stress Decomposition

Xiaogang Guo,Wei Wu,Liangtong Zhan,Ping Chen

DOI: https://doi.org/10.1007/978-3-319-97112-4_3

2018-01-01

Abstract:In Bagnold’s description of rheological properties of a solid-fluid suspension, the shear and normal stresses demonstrate linear dependence on the shear rate in the ‘macro-viscous’ regime and quadratic dependence in the ‘grain-inertia’ regime. Based on this pioneering work, a framework for the modeling of solid-fluid flows is proposed in this paper. In the framework, the total stress of the solid phase is decomposed into a frictional term contributed from prolonged contact of solid particles, a viscous term due to the viscosity of interstitial fluid and a inertia term results from particle collisions. A constitutive model for simple-shearing granular-fluid flows is developed based on this framework and verified in the element tests of granular-fluid materials under rapid shear.
Mobility and Dynamic Erosion Process of Granular Flow: Insights from Numerical Investigation Using Material Point Method

Fangwei Yu,Lijun Su,Xinpo Li,Yu Zhao

DOI: https://doi.org/10.1007/s11629-023-8502-y

IF: 2.371

2024-01-01

Journal of Mountain Science

Abstract:In order to understand the dynamics of granular flow on an erodible base soil, in this paper, a series of material point method - based granular column collapse tests were conducted to investigate numerically the mobility and dynamic erosion process of granular flow subjected to the complex settings, i.e., the aspect ratio, granular mass, friction and dilatancy resistance, gravity and presence of water. A set of power scaling laws were proposed to describe the final deposit characteristics of granular flow by the relations of the normalized run - out distance and the normalized final height of granular flow against the aspect ratio, being greatly affected by the complex geological settings, e.g., granular mass, the friction and dilatancy resistance of granular soil, and presence of water in granular flow. An index of the coefficient of friction of granular soil was defined as a ratio of the target coefficient of friction over the initial coefficient of friction to quantify the scaling extent of friction change (i.e., friction strengthening or weakening). There is a characteristic aspect ratio of granular column corresponding to the maximum mobility of granular flow with the minimum index of the apparent coefficient of friction. The index of the repose coefficient of friction of granular flow decreased gradually with the increase in aspect ratio because higher potential energy of granular column at a larger aspect ratio causes a larger kinetic energy of granular soil to weaken the friction of granular soil as a kind of velocity - related friction weakening. An increase in granular mass reduces gradually the indexes of the apparent and repose coefficients of friction of granular soil to enhance the mobility of granular flow. The mobility of granular flow increases gradually with the decrease in friction angle or increase in dilatancy angle of granular soil. However, the increase of gravity accelerates granular flow but showing the same final deposit profile without any dependence on gravity. The mobility of granular flow increases gradually by lowering the indexes of the apparent and repose coefficients of friction of granular flow while changing the surroundings, in turn, the dry soil, submerged soil and saturated soil, implying a gradually increased excessive mobility of granular flow with the friction weakening of granular soil. Presence of water in granular flow may be a potential catalyzer to yield a long run - out granular flow, as revealed in comparison of water - absent and water - present granular flows. In addition, the dynamic erosion and entrainment of based soil induced by granular flow subjected to the complex geological settings, i.e., the aspect ratio, granular mass, gravity, friction and dilatancy resistance, and presence of water, were comprehensively investigated as well.
Numerical Simulation of Two-Dimensional Granular Shearing Flows and the Friction Force of A Moving Slab on the Granular Media

Cai Qing-Dong,Chen Shi-Yi,Sheng Xiao-Wei

DOI: https://doi.org/10.1088/1674-1056/20/2/024502

2011-01-01

Chinese Physics B

Abstract:This paper studies some interesting features of two-dimensional granular shearing flow by using molecular dynamic approach for a specific granular system. The obtained results show that the probability distribution function of velocities of particles is Gaussian at the central part, but diverts from Gaussian distribution nearby the wall. The macroscopic stress along the vertical direction has large fluctuation around a constant value, the non-zero average velocity occurs mainly near the moving wall, which forms a shearing zone. In the shearing movement, the volume of the granular material behaves in a random manner. The equivalent friction coefficient between moving slab and granular material correlates with the moving speed at low velocity, and approaches constant as the velocity is large enough.
Stresses of cohesionless granular flows in liquids

Jianxin Xia,Peng Han,Jinren Ni

DOI: https://doi.org/10.1016/j.powtec.2004.12.006

IF: 5.64

2005-01-01

Powder Technology

Abstract:We construct constitutive relations for friction stress, slide stress and collision stress of cohesionless granular flows. We propose that the friction stress and slide stress could be neglected when τc/τe<0.02, where τc represents the interval time experienced by a given particle between two consecutive binary collisions and τe the particle relaxation time. We applied these constitutive relations to a simulation of solid–liquid flow in an inclined chute and found the simulation results agree with experimental data.
A Unified Constitutive Model for Pressure Sensitive Shear Flow Transitions in Moderate Dense Granular Materials.

Xiaohui Cheng,Shize Xiao,Alex Sixie Cao,Meiying Hou

DOI: https://doi.org/10.1038/s41598-021-99006-4

IF: 4.6

2021-01-01

Scientific Reports

Abstract:Granular shear flows exhibit complex transitional regimes that are dramatically affected by the pressure level and shear stress state. New advances in granular shear tests at low pressure have enlightened the understanding of the two granular shear flow transitions: between quasi-static and moderate shear flows, and between steady-state and transient shear flows. However, a unified constitutive model to describe these two transitions is yet to develop. In this work, a simplified and unified model is proposed based on innovative triaxial shear flow tests, using two dimensionless physical variables. Model results validated against experimental data suggest that the shear flow transition between a quasi-static to a moderate Isotach type flow state is highly pressure-dependent. At extremely low pressure, the granular viscosity becomes the primary mechanism, suppressing the quasi-static mechanism even under "quasi-static" shear rates. In transient to steady state granular flow transitions, a mobilized shear stress ratio or mobilized friction coefficient between zero and the critical state ratio for consolidated granular packings is taken into consideration. This is coupled with the mechanism of granular viscosity. These findings have not been discussed before and are of great relevance to granular mechanics as well as space and earthquake engineering.
Flow-Arrest Transitions in Frictional Granular Matter

Ishan Srivastava,Leonardo E. Silbert,Gary S. Grest,Jeremy B. Lechman

DOI: https://doi.org/10.1103/PhysRevLett.122.048003

2019-01-31

Abstract:The transition between shear-flowing and shear-arrested states of frictional granular matter is studied using constant-stress discrete element simulations. By subjecting a dilute system of frictional grains to a constant external shear stress and pressure, friction-dependent critical shear stress and density are clearly identified with both exhibiting a crossover between low and high friction. The critical shear stress bifurcates two nonequilibrium steady states: (i) steady state shear flow characterized by a constant deformation rate, and (ii) shear arrest characterized by temporally decaying creep to a statically stable state. The onset of arrest below critical shear stress occurs at a time $t_{c}$ that exhibits a heavy-tailed distribution, whose mean and variance diverge as a power law at the critical shear stress with a friction-dependent exponent that also exhibits a crossover between low and high friction. These observations indicate that granular arrest near critical shear stress is highly unpredictable and is strongly influenced by interparticle friction.

Soft Condensed Matter
Stresses and orientational order in shearing flows of granular liquid crystals.

Diego Berzi,Nha Thai-Quang,Yu Guo,Jennifer Curtis

DOI: https://doi.org/10.1103/PhysRevE.93.040901

IF: 2.707

2016-01-01

Physical Review E

Abstract:We perform discrete element simulations of homogeneous shearing of frictionless cylinders and show that the particles are characterized by orientational order and form a granular liquid crystal. For elongated and flat cylinders, the alignment is in the plane of shearing, while cylinders having an aspect ratio equal to 1 and 0.8 show no orientational order. We show that the particle pressure is insensitive to the cylinder aspect ratio and well predicted by the kinetic theory of granular gases, with a singularity in the radial distribution function at contact different from that for frictionless spheres. The numerical results quantitatively agree with physical experiments on different geometries. The particle shear stress is affected by orientational anisotropy. We postulate that, for frictionless cylinders, the viscosity is roughly due to the motion of the orientationally disordered fraction of the particles, and show that it is proportional, through the order parameter, to the expression of kinetic theory. Finally, we suggest that the orientational order is the result of the competing effects of the shear rate, which induces alignment, and the granular temperature, which ramdomizes.
A General Frictional-Collisional Model for Dense Granular Flows

Pengfei Si,Huabin Shi,Xiping Yu

DOI: https://doi.org/10.1007/s10346-018-1108-8

IF: 6.153

2018-01-01

Landslides

Abstract:Landslides can often be treated as dense granular flows that are characterized by their diverse behaviors ranging from solid-like to fluid-like and classified into different regimes. Establishment of a general frictional-collisional rheology capable of capturing the important features of dense granular flows in all regimes from quasi-static to inertial is known to be important from a practical point of view. The present study suggests a rheological model that includes both collisional and frictional mechanisms in dense granular flows by adding the effect of persistent contact between granular particles into the classical kinetic theory. The kinetic theory is used to formulate the collisional stresses, while the frictional stresses are modeled based on an existing relation derived by statistically averaging the individual contact forces among cohesionless particles. The proposed frictional-collisional model is then applied to steady flows of granular materials over an inclined surface, collapses of granular columns, and unsteady flows of granular materials down an inclined surface. The numerical results on the bulk behaviors of the granular flows, such as the varying profile of the free surface and the flow velocity, are all in good agreement with available experimental data. It is shown that the proposed rheological model can well describe the entire processes of dense granular flows from initiation to final deposit or fully developed steady state. Its broad applicability to various granular flows can thus be expected.
Friction law and hysteresis in granular materials

E. DeGiuli,M. Wyart

DOI: https://doi.org/10.1073/pnas.1706105114

IF: 11.1

2017-08-15

Proceedings of the National Academy of Sciences

Abstract:Significance The macroscopic friction of particulate materials often weakens as flow rate is increased. This property is responsible for important intermittent phenomena in geophysics, including earthquakes and landslides. However, it is not understood even in simple granular materials, where it is responsible for hysteresis of the angle of repose. Here we argue that, for aerial granular flows, velocity weakening is an emergent collective property induced by endogenous mechanical noise. Our theory rationalizes previously unexplained observations, and generates experimentally testable predictions. At a microscopic level, it predicts that several microscopic quantities do not have a hard-particle limit, and characterizes their scaling behavior near jamming, which we confirm numerically.

multidisciplinary sciences
Transition of shear flow for granular materials in a numerical ring shear test

Zhibo Dong,Lijun Su,Chonglei Zhang,Zhenyu Liu,Siyou Xiao

DOI: https://doi.org/10.1007/s10035-020-01062-6

IF: 3.0103

2020-11-17

Granular Matter

Abstract:The shear flow behaviors of granular materials exist widely in natural events. Ring shear tests based on the discrete element method were carried out to study the effects of shearing rate on the transition of quasi-static and slow flow phases of granular materials. The simulated results indicated that the shear stress and normalized volume increase linearly with the square of the shearing rate, and the two corresponding critical shearing rates are the same. Through the analysis of the μeff (I) rheology model, the micro-mechanism of the transition between the quasi-static and slow flow phase has been discussed quantitatively. Additionally, the critical shearing rate under different normal stress and rolling resistance friction coefficient were tested. It is found that the critical shearing rate augments with the increase in normal stress. However, it does not change with the increase of the rolling resistance friction coefficient of granular materials. The above work on the flow phase transition of granular materials can be helpful to study the mechanism of the starting stage of geological disasters, such as landslides and debris flows.

mechanics,materials science, multidisciplinary,physics, applied
Velocity Profile Geometries and Granular Temperature Distributions in Very Dense Granular Flows

Yan Li,Wei Hu,Qiang Xu,Runqiu Huang,ChingShung Chang,Jianye Chen,Yujie Wang

DOI: https://doi.org/10.1029/2023gl104410

IF: 5.2

2024-01-14

Geophysical Research Letters

Abstract:Understanding the motion of particles in very dense granular flows is crucial for comprehending the dynamics of many geological phenomena, and advancing our knowledge of granular material physics. We conduct transparent ring shear experiments to directly observe the granular motion under relatively high‐pressure conditions, and find that the granular velocity non‐linearly decays, forming an approximately 7‐particle‐diameter‐thick localized shear band. A fitting curve underlying non‐local physics can be used to well predict velocity profile geometries that are almost independent of normal stress and shear velocity. Moreover, experimental results show monotonically decreasing granular kinetic temperature, which may be caused by energy dissipation due to more inelastic contacts under high confining pressures. The variation of granular temperature will significantly influence the local yield stress and rheological properties, which may lead to inhomogeneous fluidity of the material and thus to shear localization in very dense granular flows.

geosciences, multidisciplinary
Rheology of Sheared Polyhedral Granular Materials in Inclined Flows

Jiahui Hao,Yu Guo

DOI: https://doi.org/10.1063/5.0170230

IF: 4.6

2023-01-01

Physics of Fluids

Abstract:An investigation of frictional, Platonic solid-shaped particle flows on inclined planes is performed using the discrete element method, and the effects of particle angular shape on rheological properties are analyzed. Higher shear stresses at a specified depth of particle bed are obtained for more angular particles. As particle angularity increases, rapid surges in the coordination number and solid-phase stresses occur at a smaller critical solid volume fraction. The friction and dilatancy laws of polyhedral particle flows are significantly different from those of spherical particle flows, due to particle angularity. Nevertheless, by applying a specific rolling friction to the spherical particles, their rheological properties can match those of the polyhedral particles, indicating that the angular particle shape plays a similar role to the rolling friction in preventing particle rotation. Thus, the flows of spherical particles with a rolling friction incorporated can be used to mimic the flows of angular polyhedral particles. At last, a scaling law is adopted to describe rheological relations for various polyhedral particles based on a bulk friction coefficient, a dimensionless granular temperature, and an inertial number.
Role of gravity or confining pressure and contact stiffness in granular rheology

Abhinendra Singh,Vanessa Magnanimo,Kuniyasu Saitoh,Stefan Luding

DOI: https://doi.org/10.1088/1367-2630/17/4/043028

2014-12-02

Abstract:The steady shear rheology of granular materials is investigated in slow quasi-static states and inertial flows. The effect of the gravity field and contact stiffness, which are conventionally trivialized is the focus of this study. Series of Discrete Element Method simulations are performed on a weakly frictional granular assembly in a split-bottom geometry considering various gravity fields and contact stiffnesses. While traditionally the inertial number, i.e., the ratio of stress to strain-rate timescales describes the flow rheology, we find that a second dimensionless number, the ratio of softness and stress timescales, must also be included to characterize the bulk flow behavior. For slow, quasi-static flows, the density increases while the macroscopic friction decreases with respective increase in particle softness and gravity. This trend is added to the $\mu(I)$ rheology and can be traced back to the anisotropy in the contact network, displaying a linear correlation between macroscopic friction and deviatoric fabric in the steady state. Interestingly, the linear relation holds when the external rotation rate is increased for a given gravity field and contact stiffness.

Soft Condensed Matter
Phase transition in monodisperse granular materials: How to model it by using a strain hardening visco‐elastic‐plastic constitutive relationship

Pietro Marveggio,Irene Redaelli,Claudio di Prisco

DOI: https://doi.org/10.1002/nag.3412

IF: 4

2022-07-18

International Journal for Numerical and Analytical Methods in Geomechanics

Abstract:During heating (loading characterised by a progressive increase in strain rate) and cooling (loading characterised by a progressive decrease in strain rate) numerical tests, performed by using Discrete Element codes, granular materials experience phase transition phenomena, named in this paper ‘dry liquefaction’ (when from solid the material starts behaving like a fluid) and ‘dry resolidification’ (freezing, when the material from fluid starts behaving like a solid). The aim of this paper consists in reproducing phase transition phenomena by using a strain hardening visco‐elastic‐plastic model based on the critical state concept and kinetic theories of granular gases. The authors demonstrate that crucial is the role of isotropic softening/hardening, which describes the size of the elastic domain and the capability of the solid skeleton of storing elastic energy according to permanent force chains. The main ingredients of the model are: (i) the additivity of quasi‐static and collisional stresses, (ii) the energy balance equation governing the evolution of the granular temperature, interpreted this latter as an additional internal variable for the system for the collisional contribution, (iii) the mixed isotropic and kinematic hardening characterising the quasi‐static incremental constitutive relationship. The model has been both calibrated and validated on Discrete Element Method (DEM) numerical results, obtained by testing dry assemblies of monodisperse spheres under true triaxial loading conditions.

mechanics,materials science, multidisciplinary,engineering, geological
Granular Solid Hydrodynamics

Yimin Jiang,Mario Liu

DOI: https://doi.org/10.1007/s10035-009-0137-3

2008-12-30

Abstract:Granular elasticity, an elasticity theory useful for calculating static stress distribution in granular media, is generalized to the dynamic case by including the plastic contribution of the strain. A complete hydrodynamic theory is derived based on the hypothesis that granular medium turns transiently elastic when deformed. This theory includes both the true and the granular temperatures, and employs a free energy expression that encapsulates a full jamming phase diagram, in the space spanned by pressure, shear stress, density and granular temperature. For the special case of stationary granular temperatures, the derived hydrodynamic theory reduces to {\em hypoplasticity}, a state-of-the-art engineering model.

Soft Condensed Matter
Non-equilibrium thermodynamic analysis of quasi-static granular flows

Zhongmiao Liu,Qicheng Sun,Shixiong Song,Qingfan Shi

DOI: https://doi.org/10.7498/aps.63.034702

2014-01-01

Abstract:Granular flow is usually divided into three kinds of flow pattern, namely quasi static flow, slow flow, and rapid flow. The core issue of the research is the constitutive relation. A series of constitutive relations of application value have been received up to now, however, the study on principal theory is insufficient. Granular flow has an emergent mesoscopic structure, such as force chain network and vortex, involving complex irreversible processes. This paper studies its mesoscopic structure and principal characters, introduces the concept of two granular temperatures Tconf and Tkin of the granular flow to characterize the degree of chaotic motion and disordered configuration evolution, sets them as the non-equilibrium variables to constitute the thermodynamic state variables set for granular flow with the classical irreversible thermodynamic (CIT) variables, also determines the granular flow law of energy conversion and the entropy production rate, etc., and develops the two granular temperatures (TGT) model. Taking the simple shear quasi-static granular flow in a constant volume as example, and combining it with the discrete element method (DEM), this work confirms the material parameters needed for the TGT model, and analyzes the law of developing period and the effective coefficient of friction of steady period of granular flow. ? Chinese Physical Society.
A Kinetic Description of Collisional Frictions Between Particles and Solid Boundary in Simple Sheared Granular Flows

Lei Zhang,Deyu Zhong,Qicheng Sun,Baosheng Wu

DOI: https://doi.org/10.1016/j.powtec.2015.01.057

IF: 5.64

2015-01-01

Powder Technology

Abstract:In this study, the collisional friction between particles and solid boundaries, which plays an important role in bounded granular flows, was investigated based on the kinetic theory for granular flows. Two limiting states of relative motion between particles and solid walls, i.e., large friction/no sliding and small friction/all sliding, as well as the transition between these limiting states were considered. In order to determine the momentum transfer between solid walls and particles experiencing apparent shears, we used a second-order approximation solution to the Boltzmann equation to determine the velocity distribution function of particles, instead of assuming a simple delta or a Gaussian distribution of particle velocity as has been done in previous studies. The second-order velocity distribution function provides a detailed vision about the energy dissipation due to inelastic particle–wall collisions as well as particle–particle collisions, as it makes it possible for us to discuss how a shear rate affects the collisional friction in bounded granular flows. Comparisons with experimental observations were made for the large friction/no sliding limit, which shows that the predicted and observed collisional friction coefficients are in well agreement. Furthermore, the calculated collisional friction coefficient coincides with computer simulations in the transition regime. Analyses show that the collisional friction is significantly affected by the shear of bounded granular flows.
Geometry-dependent constitutive law for granular slow frictional drag

T. Furuta,K. Katou,S. Itoh,K. Tachibana,S. Ishikawa,H. Katsuragi

DOI: https://doi.org/10.1142/s0217979217420061

2017-04-20

International Journal of Modern Physics B

Abstract:Frictional constitutive law for very slow vertical withdrawing of a thin rod from a granular bed is experimentally studied. Using a very precise creep meter, geometry-dependent granular frictional constitutive law is particularly examined. In some previous works, a dimensionless number [Formula: see text] has been used to characterize granular frictional constitutive laws, where [Formula: see text], [Formula: see text], [Formula: see text], and [Formula: see text] are the shear strain rate, grain diameter, confining pressure, and bulk density of granular bed, respectively. It has been considered that granular frictional constitutive law expressed by [Formula: see text] is universal (almost geometry-independent) in dense flow regime. In this study, however, we find that the geometry of the system is much more crucial to characterize granular friction in a very slow withdrawing regime. Specifically, the ratio between rod and grain diameters must be an essential parameter to describe the granular frictional constitutive law. Physical meaning of the geometry-dependent constitutive law is discussed on the basis of grains-contact-number dependence of granular behavior.

physics, condensed matter, applied, mathematical

General friction law for velocity‐stress dependent phase transition in granular flow

Numerical Simulations of Granular Material Behavior under Rotation of Principal Stresses: Micromechanical Observation and Energy Consideration

Local Fluctuations and Spatial Correlations in Granular Flows under Constant-Volume Quasistatic Shear.

Constitutive Model for Granular-Fluid Flows Based on Stress Decomposition

Mobility and Dynamic Erosion Process of Granular Flow: Insights from Numerical Investigation Using Material Point Method

Numerical Simulation of Two-Dimensional Granular Shearing Flows and the Friction Force of A Moving Slab on the Granular Media

Stresses of cohesionless granular flows in liquids

A Unified Constitutive Model for Pressure Sensitive Shear Flow Transitions in Moderate Dense Granular Materials.

Flow-Arrest Transitions in Frictional Granular Matter

Stresses and orientational order in shearing flows of granular liquid crystals.

A General Frictional-Collisional Model for Dense Granular Flows

Friction law and hysteresis in granular materials

Transition of shear flow for granular materials in a numerical ring shear test

Velocity Profile Geometries and Granular Temperature Distributions in Very Dense Granular Flows

Rheology of Sheared Polyhedral Granular Materials in Inclined Flows

Role of gravity or confining pressure and contact stiffness in granular rheology

Phase transition in monodisperse granular materials: How to model it by using a strain hardening visco‐elastic‐plastic constitutive relationship

Granular Solid Hydrodynamics

Non-equilibrium thermodynamic analysis of quasi-static granular flows

A Kinetic Description of Collisional Frictions Between Particles and Solid Boundary in Simple Sheared Granular Flows

Geometry-dependent constitutive law for granular slow frictional drag