Abstract:This paper describes the research carried out in the European Commission co-funded project LEMCOTEC (Low Emission Core Engine Technology), which is aiming at a significant increase of the engine overall pressure ratio. The technical work is split in four technical sub-projects on ultra-high pressure ratio compressors, lean combustion and fuel injection, structures and thermal management and engine performance assessment. The technology will be developed at subsystem and component level and validated in test rigs up to TRL5. The developed technologies will be assessed using three generic study engines (i.e. regional turbofan, mid-size open rotor, and large turbofan) representing about 90% of the expected future commercial aero-engine market. Two additional study engines from the previous NEWAC project will be used for comparison. These are based on intercooled and intercooled-recuperated future engine concepts. The compressor work is targeting efficiency, stability margin and flow capacity by improved aerodynamic design. High-pressure and intermediate-pressure compressors are addressed. The mechanical and thermo-mechanical functions, including the variable-stator-systems, will be improved. Axial-centrifugal compressors with impeller and centrifugal diffuser are under investigation too. Three lean burn fuel injection systems are developed to match the technology to the corresponding engine pressure levels. These are the PERM (Partially Evaporating Rapid Mixing), the MSFI (Multiple Staged Fuel Injection) and the advanced LDI (Lean Direct Injection) combustion systems. The air flow and combustion systems are investigated. The fuel control systems are adapted to the requirements of the ultra-high pressure engines with lean fuel injection. Combustor-turbine interaction will be investigated. A fuel system analysis will be performed using CFD methods. Improved structural design and thermal management is required to reduce the losses and to reduce component weight. The application of new materials and manufacturing processes, including welding and casting aspects, will be investigated. The aim is to reduce the cooling air requirements and improve turbine aerodynamics to support the high-pressure engine cycles. The final objective is to have innovative ultra-high pressure-ratio core-engine technologies successfully validated at subsystem and component level. Increasing the thermal efficiency of the engine cycles relative to year 2000 in-service engines with OPR of up to 70 (at max. condition) is an enabler and key lever of the core-engine technologies to achieve and even exceed the ACARE 2020 targets on CO2, NOx and other pollutant emissions: • 20 to 30 % CO2 reduction at the engine level, exceeding both, the ACARE 15 to 20% CO2 reduction target for the engine and subsequently the overall 50% committed CO2 and the fuel burn reduction target on system level (including the contributions from operations and airframe improvements), • 65 to 70 % NOx reduction at the engine level (CAEP/2) to attain and exceed the ACARE objective of 80% overall NOx reduction (including the contributions from both, operational efficiency and airframe improvement), reduction of other emissions (CO, UHC and smoke/particulates) and • Reduction of the propulsion system weight (engine including nacelle without pylon).

Aerosol Separation and Pressure Control of a Smart Crankcase Ventilation System

An Experimental Study on Engine Dynamics Model Based In-Cylinder Pressure Estimation

Analysis of the effect of a closed crankcase ventilation system on the fuel efficiency of a compression ignition engine

Optimizing Crankcase Ventilation System of Gasoline Engine

Mixing and Evaporation Analysis of a High-Pressure SCR System Using a Hybrid LES-RANS Approach

Engine operating method and crankcase ventilation system

Crankcase ventilation system for an internal combustion engine, especially of a motor vehicle

Positive Crankcase Ventilation System

A Holistic View on Urea Injection for NOx Emission Control: Impingement, Re-atomization, and Deposit Formation

Simulating the Misting of Lubricant in the Piston Assembly of an Automotive Gasoline Engine: The Effect of Viscosity Modifiers and Other Key Lubricant Components

Tailored Air-Handling System Development for Gasoline Compression Ignition in a Heavy-Duty Diesel Engine

Mitigation of PAH and nitro-PAH emissions from nonroad diesel engines

Preferential cavitation and friction-induced heating of multi-component Diesel fuel surrogates up to 450MPa

LEMCOTEC: Improving the Core-Engine Thermal Efficiency

Characterizing and visualizing the direct injection of hydrogen into high-pressure argon and nitrogen environments

Data-Based In-Cylinder Pressure Model with Cyclic Variations for Combustion Control: A RCCI Engine Application

Evaluation of NOx and PN Emission in Relation to Actuator Control

Real-fluid simulation of ammonia cavitation in a heavy-duty fuel injector

Effects of a Dual-Loop Exhaust Gas Recirculation System and Variable Nozzle Turbine Control on the Operating Parameters of an Automotive Diesel Engine

Development of a control-oriented physical model for cylinder pressure peak estimation in SI engines

Black Box SCR Modeling and Control for Small CI Engines