Abstract:The use of soft robotic actuators is on the rise because these soft systems offer the advantage of being highly flexible, which affords safer robot-environment interactions and the gentleness necessary to handle delicate objects. However, this advantage becomes a shortcoming in high-force applications where flexible components fold and fail under large loads. Various methods were sought to meet this challenge by providing a level of rigidity to soft components, but previously proposed solutions bring their own drawbacks including bulky systems, addition of superfluous weight, and restriction of actuator motion. Alternatively, this article presents Tubular Jamming, a new and effective means of stiffening that is adaptable to motion, lightweight, and can be implemented with minimal equipment. In this study, the mechanism of tubular jamming is expounded and is demonstrated through two exemplary soft structures: a tubular jammed beam (TJB) and a tubular jammed hinge (TJH). Both TJB and TJH are exhibited in areas of fabrication, characterization, and a few possible examples of implementation in soft robotic systems. In the TJB structure, tubular jamming is found to increase bending stiffness by nearly threefold at the maximum pressure and packing ratio tested, compared with a traditional soft pneumatic actuator (SPA) beam. The TJB is shown to require less supply pressure to achieve the same performance as a traditional SPA and is shown to perform better in maintaining the vertical position of a borne object. A triangular support configuration made from TJBs is demonstrated to be proficient in weight bearing, supporting a load of nearly 33 times its own weight. In the TJH structure, tubular jamming is shown to have a compound effect on torque output, as three jammed tubule hinges produce approximately four times the torque of a single tubule hinge. The TJH is exhibited in a wearable elbow flexion device. Tubular jamming opens new possibilities for soft components to achieve the stiffness needed to perform high-force tasks such as weight bearing and large-scale actuation while retaining the suppleness to enable a safe robot-to-environment interface.

Jammkle: Fibre jamming 3D printed multi-material tendons and their application in a robotic ankle

A Compliant Robotic Leg Based on Fibre Jamming

Muscle-inspired stiffness-tunable flexible fiber jamming structure for wearable robots

Biomimetic Artificial Neuromuscular Fiber Bundles with Built-in Adaptive Feedback

A Novel Jamming Structure with Interlocking Mechanism Towards Applications in Wearable Robots

Reproduction of the Mechanical Behavior of Ligament and Tendon for Artificial Joint Using Bioinspired 3D Braided Fibers

Tubular Jamming: A Variable Stiffening Method Toward High-Force Applications with Soft Robotic Components

Fiber Jamming Transition as a Stiffening Mechanism for Soft Robotics

Development of a Tendon Driven Variable Stiffness Continuum Robot with Layer Jamming

A Review of Jamming Actuation in Soft Robotics

Stiffness-Tuneable Limb Segment with Flexible Spine for Malleable Robots

A bioinspired 3D-printable flexure joint with cellular mechanical metamaterial architecture for soft robotic hands

Composite Laminar Jamming: Toward Designing a Tunable Stiffness Hybrid Soft Robotic Actuator

Chain-Like Granular Jamming: A Novel Stiffness-Programmable Mechanism for Soft Robotics

Paediatric ankle rehabilitation system based on twisted and coiled polymer actuators.

Design, Simulation and Kinematic Verification of a Multi-Loop Ankle-Foot Prosthetic Mechanism

Underactuated Robotic Gripper with Fiber-Optic Force Sensing Tendons

Twisting and Braiding Fluid-Driven Soft Artificial Muscle Fibers for Robotic Applications

Autonomous Control of a Tendon-driven Robotic Limb with Elastic Elements Reveals that Added Elasticity can Enhance Learning

Getting a Grip: in Materio Evolution of Membrane Morphology for Soft Robotic Jamming Grippers

Safe & Accurate at Speed with Tendons: A Robot Arm for Exploring Dynamic Motion