Effects of fructose-1,6-bisphosphate on morphological and functional neuronal integrity in rat hippocampal slices during energy deprivation

Y. Izumi,A. Benz,Hiroshi Katsuki,Mio Matsukawa,David B. Clifford,C. Zorumski

DOI: https://doi.org/10.1016/S0306-4522(02)00661-9

IF: 3.708

2003-01-31

Neuroscience

Abstract:

What problem does this paper attempt to address?

Low Temperature Oxidation of Toluene in an N-Heptane/toluene Mixture

Bingjie Chen,Peng Liu,Qiang Xu,Zhandong Wang,William L. Roberts,Heinz Pitsch

DOI: https://doi.org/10.1016/j.combustflame.2022.112200

IF: 4.4

2022-01-01

Combustion and Flame

Abstract:As an important component of transportation fuels, toluene has little reactivity in the low temperature regime. However, the low temperature reactivity of toluene may be enhanced by the reaction of other reactive components (e.g., n-heptane) in fuel mixtures. This work examines low temperature oxidation of toluene in jet stirred reactor oxidation of an n-heptane/toluene mixture (1:1 in mole, 50 0-80 0 K, phi= 0.5, tau = 2.0 s, p = 1 bar). Two measurement techniques, time of flight molecular beam mass spectrometry using synchrotron vacuum ultraviolet radiation as the photon ionization source and gas chromatography mass spectrometry, were applied to identify and measure 32 species, including four polycyclic aromatic hydrocarbons (PAH) and oxygenated PAH (OPAH). Numerical simulations using the latest kinetic model from Lawrence Livermore National Laboratory predicted the mole fractions of fuel molecules and small intermediates well, but under-predicted the mole fractions of oxygenated aromatics (phenol, benzyl alcohol, and cresol). The identification of benzyl peroxide-an important intermediate-supported the proposed formation pathways for the identified aromatics. Model analysis highlighted the influence of H-atom abstraction, OH/H radical ipso substitution, and OH addition reactions of toluene on the formation of phenol, benzyl alcohol, and cresol, which may further grow to OPAH molecules by the addition of benzyl radical from H-atom abstraction of toluene. (C) 2022 The Combustion Institute. Published by Elsevier Inc. All rights reserved.
Effect of ball milling on the catalytic activity of cryptomelane for VOC oxidation

Diogo F M Santos,Olívia S G P Soares,José L Figueiredo,Manuel Fernando R Pereira

DOI: https://doi.org/10.1080/09593330.2018.1491639

Abstract:Cryptomelane-type manganese oxides prepared by a solvent-free method were evaluated as catalysts for the oxidation of ethyl acetate, ethanol and toluene. The original catalyst (K-OMS-2) presented high catalytic activity for ethyl acetate and ethanol oxidation, achieving 90% conversion into CO2 around 200°C for both pollutants. Toluene was much harder to oxidize, requiring a temperature near 270°C for the same conversion. The original catalyst was mechanically treated in a ball mill at different intensities, in order to decrease the particle size for subsequent impregnation onto structured supports, as small particle sizes are usually recommended. The catalytic activity of the materials decreases with the increase in the severity of this treatment, which is related to the decrease of the surface area of the catalysts, since the other properties (phase purity, thermal stability, surface oxygen, average oxidation state and reactivity of the oxygen species) are similar among the catalysts with different ball milling treatments. For comparison, a platinum-based catalyst (1%-Pt/Al2O3) was also tested, which exhibited a high activity for toluene, but much lower activities for the two other volatile organic compounds tested. A long-term experiment, using ethanol as model pollutant, showed that the cryptomelane catalyst was stable for more than 100 h.
Effect of ambient factors over spinel CuMn2O4 for toluene catalytic ozonation: Enhancement of the synergy and the generation of ROS

Guanjie Wang,Bo Zhao,Zhiping Ye,Liang Zhao,Xiuwen Zhang,Jiade Wang

DOI: https://doi.org/10.21203/rs.3.rs-2145432/v1

2022-01-01

Abstract:Abstract Herein, the effect of ambient factors (O3 concentration, temperature, and humidity) was explored in catalytic ozonation of toluene by using CuMn2O4, which possessed a great steady-state activity (~ 73%) at the optimal conditions (2100 ppm O3, 100℃, and dry air). Under various conditions, a strong correlation was observed between O3 consumption, toluene oxidation, and COx formation. The technology of DRIFTS and GC-MS were used to study the effects of influencing factors on the toluene degradation process. Cu+ plays an important role in the adsorption of toluene and the oxidation of toluene to benzoic acid. The ·OH and temperature suppressed the deposition of carbonaceous by-products. On the other hand, the situation of the effect of influence factors was investigated by SEM, BET, XPS, and TG. It is revealed that reactive oxygen species are the key to catalytic ozonation and participate in catalytic oxidation of toluene as an electron transfer intermediate on active sites (Cux+-Ov-Mny+).
Catalytic Ozonation of Toluene over Spinel Cumn2o4: Influencing Factors, Reaction Mechanism and Pathways

Guanjie Wang,Zhiping Ye,Liang Zhao,Jiayu Ji,Yang Liu,Jiade Wang

DOI: https://doi.org/10.2139/ssrn.4046600

2022-01-01

SSRN Electronic Journal

Abstract:Herein, the effect of influence factors (O3 concentration, temperature, and humidity) was explored in catalytic ozonation of toluene by using CuMn2O4 , which possessed a great steady-state activity at the optimal conditions. Under various conditions, a strong correlation was observed between O3 consumption, toluene oxidation, and COx formation. The technology of DRIFTS and GC-MS were used to study the effects of influencing factors on the toluene degradation process. Except for the intermediate content, no significant difference could be found in the types of byproducts, indicating the discrepancy of intermediate oxidation rate at different conditions. On the other hand, the situation about the effect of influence factors was investigated by SEM, BET, XPS, and TG. It is revealed that reactive oxygen species is the key to catalytic ozonation and participates in catalytic oxidation as an electron transfer intermediate. The speed of electron transfer is one of the main reasons for the impact of different influencing factors on performance.
Mechanistic Insight into the Mutual-Effect and Key Intermediate During Methanol Accelerating Toluene Decomposition over Co-spinel Catalyst Revealed by PTR-TOF-MS and DFT Calculation

Jinping Zhong,Zheng Yin,Tan Li,Yikui Zeng,Fada Feng,Quanming Ren,Dengfeng Yan,Tao Dong,Yuanyuan Meng,Haibao Huang,Daiqi Ye

DOI: https://doi.org/10.1016/j.apcatb.2024.124075

2024-01-01

Abstract:Revealing the inherent mechanism of multi-component VOCs paves the way for the development of new efficient catalysts applicable to the practical elimination of VOCs. For two primary co-existing industry VOCs of toluene and methanol, their synergetic and efficient oxidation are investigated based on two Co3O4 catalysts with exposed {111} and {110} faces. The promoting effect of methanol on toluene oxidation, with a significant decrease in conversion temperature compared to that of toluene alone, has experimentally and theoretically identified for the first time. The formaldehyde produced by methanol oxidation reacts with toluene to form 2-methylbenzaldehyde as a key intermediate, leading to a lower energy barrier in the aromatic-ring-opening of toluene during the oxidation path. The intrinsically higher conversion temperature of toluene than methanol synchronously guarantees the full decomposition of methanol. This work sheds light on a new insight into the reaction mechanism of the mutual-effect produced by multi-component VOC oxidation.
Deep Catalytic Oxidation of Benzene, Toluene, Ethyl Acetate over Pd/Sba-15 Catalyst: Reaction Behaviors and Kinetics

Chi He,Lin Yue,Xinyan Zhang,Peng Li,Baojuan Dou,Chunyan Ma,Zhengping Hao

DOI: https://doi.org/10.1002/apj.621

2012-01-01

Asia-Pacific Journal of Chemical Engineering

Abstract:ABSTRACTThis work aimed at investigating the reaction behaviors and kinetics of catalytic oxidation of benzene, toluene, and ethyl acetate over Pd/SBA‐15 catalyst. Results for single components show that toluene (T50 = 185–215 °C) is more easily oxidized than ethyl acetate (T50 = 220–255 °C) and benzene (T50 = 215–290 °C). The conversion of toluene and benzene decreases continuously as their inlet concentrations are increased. The conversion of ethyl acetate increases slightly when its feed concentration increases in a small range, while this trend is not kept when the concentration is further raised. Results for multicomponents reveal that the presence of benzene or toluene inhibits the conversion of ethyl acetate, and the aromatic hydrocarbons inhibit each other. Ethyl acetate has an inhibitory effect on benzene, while it is interested to note that the promotion behaviors are observed for toluene. Kinetic results of all studied volatile organic compounds obtained in the absence of diffusion limitations are fit to the Mars‐van Krevelen expressions. © 2011 Curtin University of Technology and John Wiley & Sons, Ltd.
Optimization of the preparation conditions of cordierite honeycomb monoliths washcoated with cryptomelane-type manganese oxide for VOC oxidation

Diogo F M Santos,Olívia S G P Soares,José L Figueiredo,Manuel Fernando R Pereira

DOI: https://doi.org/10.1080/09593330.2019.1705398

Abstract:Ceramic honeycomb monoliths were washcoated with cryptomelane-type manganese oxides and their catalytic performance was evaluated in the oxidation of ethyl acetate. The effect of a mixture of ethyl acetate with toluene and of the presence of water vapour was also assessed.Different coating parameters, namely size of catalyst particles, number of immersions in the washcoating solution, presence of an initial coating with alumina, calcination temperature of this coating, as well as the amount of binding agent and ethanol in the washcoating solution were studied and optimized based on the catalytic activity of the structured catalyst. Small particles are required for a correct impregnation; however, since the smallest particles are less active, an intermediate size achieved the best catalytic results. Increasing the number of immersions over 3 did not significantly increase the catalytic activity of the structured catalyst. The presence of an initial coating with alumina and a binding agent (colloidal alumina) in the washcoating solution was found essential to increase the activity, whereas increasing the calcination temperature after the initial alumina coating above 500°C decreased the activity of the catalyst. The presence of ethanol in the washcoating solution did not significantly improve the activity of the structured catalyst.The optimized structured catalyst presented high catalytic activity in the removal of ethyl acetate (90% conversion into CO2 at 256°C) and high stability during 100 h of reaction. The addition of toluene or water vapour in the feed gas did not significantly affect the activity of the coated monolith.
Unraveling the opposite behaviors of Pt/MOx catalysts for toluene and o-xylene mixture oxidation: Modulating mixing effect by optimization supports

Qiuling Wang,Jing Li,Song Wu,Jingping Feng,Jiali Lu,Zuliang Wu,Erhao Gao,Wei Wang,Jiali Zhu,Shuiliang Yao,Nanhua Wu

DOI: https://doi.org/10.1016/j.seppur.2024.130536

IF: 8.6

2024-11-26

Separation and Purification Technology

Abstract:Actual industrial emissions usually contain multiple aromatic VOCs, but little is known about adsorption and oxidation behaviors of multicomponent aromatic VOCs over catalysts, which limits the practical application of catalytic oxidation technology. Herein, the adsorption and oxidation of toluene and o-xylene mixture generated during paint production over Pt-based supported catalysts (Pt/NiO, Pt/Co 3 O 4 , Pt/Nb 2 O 5 and Pt/CeO 2 ) were investigated. Pt/Nb 2 O 5 and Pt/CeO 2 catalysts significantly promoted the oxidation of mixture. However, Pt/NiO and Pt/Co 3 O 4 catalysts exhibited more difficulties in degrading mixed VOCs. Characterization results revealed that Pt/NiO and Pt/Co 3 O 4 possessed higher percentage of surface adsorbed oxygen. Pt/Nb 2 O 5 and Pt/CeO 2 had more surface lattice oxygen, Pt 0 species and acid sites. The weak competitive adsorption over Pt/Nb 2 O 5 and Pt/CeO 2 catalysts might be related to their acidic and electronic properties. In situ experiments proved that surface adsorbed oxygen and surface lattice oxygen of Pt/CeO 2 could oxidize toluene and o-xylene simultaneously at lower temperature. However, the depleted oxygen species on Pt/Co 3 O 4 could not be replenished in time due to the strong competitive adsorption and different oxidation mechanisms. This study uncovers the mixing effect of toluene and o-xylene over Pt/MOx catalysts, which provides a guiding direction towards the development of catalysts for efficient degradation of multicomponent VOCs.

engineering, chemical
Performance and Reaction Mechanisms of Catalytic Combustion of Toluene and Ethyl Acetate Over Fe‐Mn Oxides

Wenyan Wang,Zhihong Zhang,Zhekai Sun,Xiaogang Du

DOI: https://doi.org/10.1002/slct.202305204

2024-06-04

ChemistrySelect

Abstract:The catalytic oxidation of VOCs over catalysts is a multi‐step reaction process and the reaction follows the Mars‐van Krevelen (MVK) mechanism. The reaction mechanism of toluene is: toluene→benzaldehyde→benzyl alcohol, benzoic acid→CO2+H2O. The oxidation route of ethyl acetate is: ethyl acetate→ethanol→acetic acid→CO2+H2O. In this paper, Fe−Mn oxide catalysts were prepared by the co‐precipitation method. (Fe2O3)‐(Mn3O4)‐3 : 1 showed the best catalytic activity in the degradation of toluene and ethyl acetate, with the removal rate reaching 90 % at 166 °C and 156 °C respectively. The XRD, SEM, TEM, and XPS characterizations revealed that the interaction between Fe and Mn and the higher surface adsorption of oxygen in the (Fe2O3)‐(Mn3O4)‐3 : 1 catalyst may be the main factors promoting the catalytic oxidation. (Fe2O3)‐(Mn3O4)‐3 : 1 exhibited a better removal rate in ethyl acetate than toluene at different space velocities, concentrations and water contents. Under the same conditions, the degradation rate of (Fe2O3)‐(Mn3O4)‐3 : 1 in ethyl acetate was also greater than that in xylene and butyl acetate, which was related to their oxidation processes. FT‐IR and GC‐MS characterizations of fresh and used (Fe2O3)‐(Mn3O4)‐3 : 1 catalysts revealed intermediates in the oxidation of volatile organic compounds, and the reaction mechanisms were analyzed: Firstly, VOCs molecules were adsorbed on the catalyst surface, then decomposed into organic intermediates and oxidized to CO2 and H2O finally.

chemistry, multidisciplinary
The Synergistic Effect of Benzyl Benzoate on the Selective Oxidation of Toluene to Benzaldehyde

Chen Lu,Jiaming Hu,Yuning Meng,Aidong Zhou,Feng Zhang,Zhibing Zhang

DOI: https://doi.org/10.1016/j.cherd.2018.10.019

IF: 7.8

2019-01-01

Process Safety and Environmental Protection

Abstract:To resolve the defects of acetic acid solvents for the liquid-phase oxidation of toluene to benzaldehyde with oxygen, a low-corrosive and green method was developed by introducing benzyl benzoate into the reaction. It was found that compared with the case of acetic acid, benzyl benzoate showed gratifying effect on the oxidation of toluene to benzaldehyde. The reaction was more active in the initial stage of oxidation, and the generated benzaldehyde was protected from further oxidation due to the synergistic effect of benzyl benzoate along with toluene-derived products benzyl alcohol and benzyl bromide. Benzyl benzoate inhibited the esterification of benzyl alcohol, while benzyl bromide promoted the formation of benzyl alcohol. Therefore, considerable benzyl alcohol concentration could be maintained and high benzaldehyde selectivity could be achieved under high toluene conversion. (C) 2018 Institution of Chemical Engineers. Published by Elsevier B.V. All rights reserved.
Modulate synthesis of CeMn solid solution using various alcohols for toluene catalytic oxidation: synergistic effect of Ce-Mn and reaction mechanism

Ye Jiang,Yinsheng Jiang,Siyuan Cheng,Yanyan Xi,Xin Sun,Yichao Xu,Zhengda Yang

DOI: https://doi.org/10.1016/j.jhazmat.2024.135051

IF: 13.6

2024-07-03

Journal of Hazardous Materials

Abstract:A redox co-precipitation method was employed to synthesize CeMn homogeneous solid solutions, utilizing various alcohols as activating agents. Ethanol effectively orchestrated the precipitation of CeO 2 and MnO x , promoting their co-growth. As a result, the CeMn-EA achieved 90 % toluene conversion at 218 °C ( T 90 =218 °C) with a weight hourly space velocity (WHSV) of 48000 ml/(g·h). It also demonstrated high adaptability to increased WHSV, suggesting its potential for industrial-scale applications. The uniform dispersion of Ce and Mn accelerated the coupling between Ce 3+ /Ce 4+ and Mn 4+ /Mn 3+ , engineering numerous oxygen vacancies, which enhanced the activation of gas-phase oxygen and the mobility of lattice oxygen. In situ DRIFTS confirmed that toluene oxidation accommodated both Langmuir-Hinshelwood (L-H) and Mars-van Krevelen (MvK) mechanisms, with benzoate identified as a pivotal intermediate. Enhanced oxygen mobility facilitated the cleavage of the benzene ring, which was the rate-determining step. Additionally, the introduction of H 2 O significantly enhanced the dissociation and adsorption of toluene and facilitated the activation of gas-phase oxygen. At higher temperatures, H 2 O could further activate lattice oxygen engaging in toluene oxidation. Environmental Implication Volatile organic compounds (VOCs) have emerged as major air pollutants due to the changes in air pollution patterns. They can act as precursors to near-surface ozone and haze. Toluene, a typical VOC, is primarily released from anthropogenic sources and poses significant risks to human health and the environment. Ce-based catalysts have been demonstrated efficiency in toluene oxidation due to their excellent oxygen storage and release properties. This study synthesized CeMn homogeneous solid solutions utilizing various alcohols as activating agents, which possessed abundant oxygen vacancies and optimum oxygen activation capacity to oxidize toluene in time.

environmental sciences,engineering, environmental
Efficient catalytic oxidation of VOCs by a Pd-Pt/SiO 2 catalyst: The cooperative catalysis of dual metal sites

Jinglei Cui,Yujun Cui,Jingjing Tan,Huirong Zhang,Mengyuan Gu,Long Huang

DOI: https://doi.org/10.1016/j.jece.2024.111930

IF: 7.7

2024-01-17

Journal of Environmental Chemical Engineering

Abstract:Volatile organic compounds (VOCs) are one of the main pollutants produced in industrial processes. Catalytic oxidation is an effective method to eliminate VOCs, and the key lies in designing efficient metal catalyst. In this work, Pd-Pt/SiO 2 bimetallic catalysts were designed and prepared by the immobilization method, and their performances for toluene oxidation were evaluated. The addition of Pt into the catalyst elevated markedly the reduction of Pd active sites, leading to abundant electron-deficient Pd 0 and electron-rich Pt 0 in the Pd 2 Pt 1 catalyst, which were confirmed by TEM, CO pulse adsorption and in-situ XPS. As revealed by O 2 -TPD and toluene-TPD characterization, the cooperative effect of electron-deficient Pd 0 and electron-rich Pt 0 in Pd 2 Pt 1 catalyst facilitated the activation of O 2 and toluene, thus enhanced greatly its activity. A conversion of 90% (T 90 ) for toluene was achieved over Pd 2 Pt 1 catalyst at 165 °C, and the apparent activation energy ( E a ) over Pd 2 Pt 1 catalyst was lower than that over other Pd-Pt bimetallic and monometallic Pd or Pt catalysts. Additionally, the reaction mechanism was studied by In - situ DRIFTS, the results showed that the toluene oxidation passed successively benzyl alcohol, benzaldehyde, benzoic acid and maleic anhydride, then maleic anhydride was further oxidized to CO 2 and water.

engineering, chemical, environmental
Influences of different surface oxygen species on oxidation of toluene and/or benzene and their reaction pathways over Cu-Mn metal oxides

Mingyang Li,Wanlu Zhang,Xuewei Zhang,Yongfu Lian,Xiaoyu Niu,Yujun Zhu

DOI: https://doi.org/10.1016/j.jcis.2022.10.107

2023-01-15

Abstract:Catalytic oxidation is considered as the most effective and economical method to remove low concentration volatile organic compounds (VOCs). Activation of oxygen to form active oxygen species on metal oxides catalyst plays a key role in the process. Three copper-manganese oxide catalysts with cubic Cu1.5Mn1.5O4 phases were prepared by microwave heating (CM-MW), sol-gel (CM-SG) and co-precipitation (CM-CP) methods, and applied for the elimination of toluene and benzene as representative aromatic VOCs. These catalysts exhibit different catalytic oxidation performance due to their different physicochemical properties. Various characterizations were used to clarify the role of different oxygen species in the oxidation of VOCs, and the reaction pathway. In situ DRIFTS were carried out to explore the function of surface adsorbed oxygen, oxygen vacancy, and surface lattice oxygen in the catalytic oxidation of VOCs over three catalysts. Various types of intermediate species and detailed reaction pathways are also explored by combining in situ DRIFTS and mass spectrometry. Among these catalysts, CM-MW with nanosheet morphology shows the best catalytic oxidation performance of toluene and/or benzene with/without H2O due to the most abundant active oxygen species, and the highest oxygen vacancy concentration which is beneficial to activate oxygen. Meanwhile, toluene and benzene do not interfere with each other during the mixture oxidation. This study can provide new inspiration for rational design of metal oxide catalysts to remove VOCs.
Partial Oxidation of Toluene in CH3COOH by H2O2 in the Presence of VO (acac)2 Catalyst

Xueqin Wang,Junping Wu,Mingwei Zhao,Yufen Lv,Guiying Li,Changwei Hu

DOI: https://doi.org/10.1021/jp9028062

2009-01-01

Abstract:The partial oxidation of toluene by hydrogen peroxide with catalytic amount of bis (acetylacetonato) oxovanadium (VO(acac)(2)) in acetic acid is studied in detail. Benzaldehyde is found to be the main product in the reaction, and (VNMR)-N-51 and ESI-MS are used to detect the possible intermediate species' The effect of reaction parameters, such as the amounts of catalyst and hydrogen peroxide used, the reaction temperature, and reaction time on the reaction are investigated. The mechanism of toluene partial oxidation is also studied, and the hydroxyl radical is found to be the key active species. The solvent acetic acid coordinates with vanadium atom, and the toluene partial oxidation passes through cage reaction to form the C6H5CH center dot(OOH) radical, which promptly decomposes to benzaldehyde and hydroxyl radical. C6H6CH2OOCH2C6H6 is also found to be one possible intermediate.
[Measles in Poland in 2009].

J. Rogalska

Przeglad Epidemiologiczny

Abstract:In Poland 115 measles cases were registered in 2009 (0.3 per 100,000 population). The most affected age group were children aged 0-4 years (incidence 2.02 per 100,000 population) and 6-year olds (1.43). 79 measles cases (69%) were hospitalized, no deaths were recorded. Poland participates in the WHO Measles Elimination Strategy. Presently, the most important is the maintenance of a sensitive and timely surveillance of measles and measles-compatible cases, with serologic testing of one suspect case per 100,000 population. The performance of the surveillance system was insufficient with only 147 measles-compatible cases reported in 2009 (39% of expected reports). Serologic confirmation of cases was also insufficient, with 62 cases (54%) confirmed by IgM ELISA test. These results indicate the need to maintain the high immunisation coverage and improve measles surveillance system.
Catalytic ozonation of multi-VOCs mixtures over Cr-based bimetallic oxides catalysts from simulated flue gas: Effects of NO/SO 2 /H 2 O

Peixi Liu,Hairong Tang,Jiaming Shao,Yong He,Yanqun Zhu,Elisabete C B A Alegria,Zhihua Wang,Armando J L Pombeiro,Elisabete C.B.A. Alegria,Armando J.L. Pombeiro

DOI: https://doi.org/10.1016/j.chemosphere.2023.139851

IF: 8.8

2023-08-24

Chemosphere

Abstract:Different Cr-based bimetallic oxides were prepared, and their catalytic performance was evaluated on the simultaneous removal of multi-VOCs mixtures (acetone, benzene, toluene, and o -xylene) by ozonation. Among them, Co–Cr catalyst stood out in catalytic ozonation of aromatic VOCs, and its activity on acetone conversion was promoted by raising the temperature and ozone concentrations, owing to lower crystallization, larger surface area, excellent redox and VOCs/CO 2 desorption ability. Above 95% conversion of all multi-VOCs was achieved over the Co–Cr catalyst when the temperature was 100 °C and an excess ozone ratio λ (the ratio of actual moles of ozone to theoretical moles of ozone needed) was equal to 3. A competitive relationship was noticed during the removal process of four multiple VOCs, with significant inhibition of acetone conversion in the presence of aromatic VOCs, conceivably due to adsorption competition and byproducts accumulation. Effects of NO/SO 2 /H 2 O and respective reversibility were also investigated. The inhibition effects of NO/SO 2 /H 2 O on aromatic VOCs were far less than those on acetone. Further, the retarding effect of NO was reversible, attributing to physical adsorption competition, but the inhibition effect of SO 2 /H 2 O was irreversible, due to the blockage of active sites for VOCs removal. With the combination of scrubbing, multi-VOCs and NO/SO 2 could be removed by catalytic ozonation simultaneously and efficiently. In-situ DRIFTS measurement was also conducted to investigate the adsorption and catalytic ozonation process of multi-VOCs mixtures, as well as under the presence of SO 2 /H 2 O, discovering the major intermediates, surface carboxylates and carboxylic acids.

environmental sciences
Synergistic photothermal catalytic oxidation of methanol and toluene mixture over Co-MOFs-derived catalyst: Interfacial and promotion effects

Yikui Zeng,Jinping Zhong,Fada Feng,Daiqi Ye,Yun Hu

DOI: https://doi.org/10.1016/j.cej.2024.149720

IF: 15.1

2024-04-01

Chemical Engineering Journal

Abstract:Herein, a series of Co/CoOx@CN nanocomposites with tunable synergistic interfacial structure were successfully obtained by a facile pyrolysis treatment. Among these nanocomposites, the nanocomposite pyrolyzed at 500 °C (denoted as Co/CoOx@CN-500) exhibited the best methanol photothermal catalytic activity (97% methanol conversion and 96% CO2 yield) under simulated solar irradiation. Compared with Co nanoparticles and Co@CN, Co/CoOx@CN-500 showed higher methanol photothermal catalytic activity. Moreover, the Co/CoOx@CN-500 also displayed a good ability to degrade methanol under outdoor natural solar. Such excellent photothermal activity mainly benefited from the strong interaction between the metals Co, CoOx and graphitic-carbon, which enhanced the photothermal effect by inducing the high work temperature, and the surface adsorb oxygen species of Co/CoOx@CN-500. Besides, the promotion effect of methanol on toluene oxidation was observed over Co/CoOx@CN-500 for the photothermal catalytic oxidation of the methanol and toluene mixture relative to their individual component. Water molecules did not affect the promotion effect of methanol on the photothermal catalytic oxidation of toluene. Reaction mechanism studies showed that 2-methylbenzaldehyde, the key intermediate formed by the reaction of formaldehyde generated by methanol oxidation and toluene, is the main reason for the improvement of the oxidation activity of toluene.

engineering, chemical, environmental
Insight into the catalytic performance and reaction routes for toluene total oxidation over facilely prepared Mn-Cu bimetallic oxide catalysts

Jian-Rong Li,Wan-Peng Zhang,Chang Li,Hang Xiao,Chi He

DOI: https://doi.org/10.1016/j.apsusc.2021.149179

IF: 6.7

2021-06-01

Applied Surface Science

Abstract:Developing facile preparation method to obtain the satisfied low-temperature catalytic performance of transitional metal oxide-based materials is still a challenge in deep degradation of VOCs. Here, a series of Mn-Cu bimetallic oxide catalysts were prepared by one-step hydrothermal-redox method for catalytic total oxidation of toluene. The CH3COOH concentration, Cu/Mn molar ratio and calcination temperature greatly affected the crystal structure, micromorphology and catalytic performance. Amongst, MnCu spinel structured catalyst exhibited excellent low-temperature catalytic activity, superior durability and water resistance in toluene total oxidation owing to its abundant surface adsorbed oxygen species, higher amount of Cu+ and Mn3+ and excellent low-temperature reducibility. The reaction rate of MnCu was 7.0 times higher than that of MnCu0.5 at 210 °C. The cyclic redox process with enough oxygen vacancy played a vital role in toluene oxidation. The deep oxidation of benzene was the key step in the toluene oxidation. Proton transfer reaction-mass spectrometry (PTR-MS) results revealed the reaction intermediates including benzaldehyde, benzene and phenol, which further decomposed to acetone, ethanol, acetic acid, ketone and acetaldehyde by ring opening before total mineralization. Therefore, PTR-MS provided a facile method to investigate the reaction mechanism of toluene oxidation.

chemistry, physical,physics, applied, condensed matter,materials science, coatings & films
Study of the Catalyst for the Vapor Phase Selective Oxidation from P-Tert Butyl Toluene to P-Tert Benzalde-Hyde

陈敏,袁贤鑫,周仁贤,郑小明

DOI: https://doi.org/10.3321/j.issn:1008-9497.2002.03.012

2002-01-01

Abstract:A series of catalysts for the vapor phase selective oxidation from p-tert butyl toluene to p-tert benzaldehyde were prepared by the impregnation method. The effects of the reaction conditions such as reaction temperature, space velocity, concentration of p-tert betyl toluene, and stability of catalysts were investigated. The results showed that under suitable conditions the selectivity of p-tert benzaldehyde can be as high as 80 mol% and the conversion of p-tert butyl toluene can reach 12 mol%. The catalyst retained excellent reaction properties after running for 365 hours. The catalyst showed broad application prospects both for industry and environmental protection.
Solvent-free catalytic oxidation of toluene over heterogeneous CeMnOx composite oxides

Gui Chen,Kuiyi You,Fangfang Zhao,Zhenpan Chen,Hean Luo

DOI: https://doi.org/10.1007/s11164-022-04727-4

IF: 3.134

2022-05-13

Research on Chemical Intermediates

Abstract:An inexpensive and controllable CeMnO x composite oxides catalyst for the liquid-phase catalytic oxidation of toluene was conveniently prepared by ultrasound-assisted co-precipitation method. The physical–chemical properties of CeMnO x composite oxides catalyst have been systematically characterized. MnO x as catalytic active species was highly dispersed in the cubic fluorite structure CeO 2 . The cooperation of CeO 2 and MnO x evidently improved the catalytic performance. CeMnO x composite oxides with a Ce/Mn molar ratio of 2:1 was showed the good catalytic performance. 7.0% of toluene conversion and 95.6% of overall selectivity to benzylalcohol, benzaldehyde and benzoic acid was acquired under optimal reaction conditions. The present catalyst has the advantages of low cost, good catalytic performance and stability. This work provides a simple, benign and controllable approach for the selective oxidation of toluene to valuable oxidation products.

chemistry, multidisciplinary

Effects of fructose-1,6-bisphosphate on morphological and functional neuronal integrity in rat hippocampal slices during energy deprivation

Low Temperature Oxidation of Toluene in an N-Heptane/toluene Mixture

Effect of ball milling on the catalytic activity of cryptomelane for VOC oxidation

Effect of ambient factors over spinel CuMn2O4 for toluene catalytic ozonation: Enhancement of the synergy and the generation of ROS

Catalytic Ozonation of Toluene over Spinel Cumn2o4: Influencing Factors, Reaction Mechanism and Pathways

Mechanistic Insight into the Mutual-Effect and Key Intermediate During Methanol Accelerating Toluene Decomposition over Co-spinel Catalyst Revealed by PTR-TOF-MS and DFT Calculation

Deep Catalytic Oxidation of Benzene, Toluene, Ethyl Acetate over Pd/Sba-15 Catalyst: Reaction Behaviors and Kinetics

Optimization of the preparation conditions of cordierite honeycomb monoliths washcoated with cryptomelane-type manganese oxide for VOC oxidation

Unraveling the opposite behaviors of Pt/MOx catalysts for toluene and o-xylene mixture oxidation: Modulating mixing effect by optimization supports

Performance and Reaction Mechanisms of Catalytic Combustion of Toluene and Ethyl Acetate Over Fe‐Mn Oxides

The Synergistic Effect of Benzyl Benzoate on the Selective Oxidation of Toluene to Benzaldehyde

Modulate synthesis of CeMn solid solution using various alcohols for toluene catalytic oxidation: synergistic effect of Ce-Mn and reaction mechanism

Efficient catalytic oxidation of VOCs by a Pd-Pt/SiO 2 catalyst: The cooperative catalysis of dual metal sites

Influences of different surface oxygen species on oxidation of toluene and/or benzene and their reaction pathways over Cu-Mn metal oxides

Partial Oxidation of Toluene in CH3COOH by H2O2 in the Presence of VO (acac)2 Catalyst

[Measles in Poland in 2009].

Catalytic ozonation of multi-VOCs mixtures over Cr-based bimetallic oxides catalysts from simulated flue gas: Effects of NO/SO 2 /H 2 O

Synergistic photothermal catalytic oxidation of methanol and toluene mixture over Co-MOFs-derived catalyst: Interfacial and promotion effects

Insight into the catalytic performance and reaction routes for toluene total oxidation over facilely prepared Mn-Cu bimetallic oxide catalysts

Study of the Catalyst for the Vapor Phase Selective Oxidation from P-Tert Butyl Toluene to P-Tert Benzalde-Hyde

Solvent-free catalytic oxidation of toluene over heterogeneous CeMnOx composite oxides