Abstract:Shear-mode piezoelectric materials have been widely used to shunt the damping of vibrations where utilizing surface or interface shear stresses. The thick-shear mode (TSM) elastic constant and the mechanical loss factor can change correspondingly when piezoelectric materials are shunted to different electrical circuits. This phenomenon makes it possible to control the performance of a shear-mode piezoelectric damping system through designing the shunt circuit. However, due to the difficulties in directly measuring the TSM elastic constant and the mechanical loss factor of piezoelectric materials, the relationships between those parameters and the shunt circuits have rarely been investigated. In this paper, a coupling TSM electro–mechanical resonant system is proposed to indirectly measure the variations of the TSM elastic constant and the mechanical loss factor of piezoelectric materials. The main idea is to transform the variations of the TSM elastic constant and the mechanical loss factor into the changes of the easily observed resonant frequency and electrical quality factor of the coupling electro–mechanical resonator. Based on this model, the formular relationships are set up theoretically with Mason equivalent circuit method and they are validated with finite element (FE) analyses. Finally, a prototype of the coupling electro–mechanical resonator is fabricated with two shear-mode PZT5A plates to investigate the TSM elastic constants and the mechanical loss factors of different circuit-shunted cases of the piezoelectric plate. Both the resonant frequency shifts and the bandwidth changes observed in experiments are in good consistence with the theoretical and FE analyses under the same shunt conditions. The proposed coupling resonator and the obtained relationships are validated with but not limited to PZT5A.

Multimode piezoelectric shunt damping of thin plates with arrays of separately shunted patches, method, and experimental validation

A Numerical Approach for Modeling the Shunt Damping of Thin Panels with Arrays of Separately Piezoelectric Patches

Vibration Suppression of a Composite Prosthetic Foot Using Piezoelectric Shunt Damping: Implications to Vibration-Induced Cumulative Trauma

A Study of Segmentation of Distributed Piezoelectric Sensors and Actuators, Part I: Theoretical Analysis

A Study of Segmentation of Distributed Piezoelectric Sensors and Actuators, Part II: Parametric Study and Active Vibration Controls

Damping Enhancement of Composite Panels by Inclusion of Shunted Piezoelectric Patches: A Wave-Based Modelling Approach

Distributed piezoelectric sensor/actuator design for dynamic measurement/control of distributed parameter systems: A piezoelectric finite element approach

Experimental Study on Damping Characteristics of Piezoceramic Materials Shunted by Passive Electrical Circuits

Vibration Suppression on the Composite Laminated Plates Subjected to Aerodynamic and Harmonic Excitations Based on the Nonlinear Piezoelectric Shunt Damping

Theoretical analysis of a multi-layered thin shell coupled with piezoelectric shell actuators for distributed vibration controls

Finite Difference Based Electrical Modeling and Vibration Control Simulation of Piezoelectric Structronic Plate System

Distributed Modal Identification and Vibration Control of Continua: Piezoelectric Finite Element Formulation and Analysis

Distributed Multi-Flexoelectric Actuation and Control of Plates

Finite Difference Based Vibration Simulation Analysis of a Segmented Distributed Piezoelectric Structronic Plate System

Modeling Analysis and Tuning of Shunt Piezoelectric Damping Controller for Structural Vibration

Distributed Actuation Effectiveness of Flexible Parabolic Cylindrical Panels

Three-Dimensional Semianalytical Solutions For Piezoelectric Laminates Subjected To Underwater Shocks

Investigations of Thickness-Shear Mode Elastic Constant and Damping of Shunted Piezoelectric Materials with a Coupling Resonator

PARAMETRIC STUDY OF SEGMENTED TRANSDUCERS LAMINATED ON CYLINDRICAL SHELLS, PART 2: ACTUATOR PATCHES

Vibration Control of Toroidal Shells with Parallel and Diagonal Piezoelectric Actuators

Kirchhoff plate theory-based electromechanically-coupled analytical model considering inertia and stiffness effects of a surface-bonded piezoelectric patch