Abstract:This research focuses on the influences of the deposited layer thickness upon the material characteristics, dimensional accuracy, and also the surface roughness of AISI D2 tool steel processed by laser directed energy deposition (L-DED); while layer thickness was varied, the remaining L-DED system parameters were retained at fixed values. After laser deposition, the D2 specimens were assessed without applying any subsequent machining steps. Sample dimensional accuracy was assessed through both manual measurement and computational methods, with the latter using confocal laser scanning microscopy (CLSM). It was shown that increasing the layer thickness decreases the extent of sample overbuilding. The use of lower layer thicknesses reduced the top surface roughness. However, a monotonic effect was not observed for side surface roughness in relation to the deposited layer thickness. In addition, the microstructures of the L-DED samples were evaluated using a combination of scanning electron microscopy (SEM) with associated energy dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD). It is shown that a dendritic morphology is formed for the L-DED processed samples, with a columnar grain structure. Furthermore, the primary crystalline phase generated with the dendritic structure was found to be austenite. The indentation hardness values for the L-DED fabricated parts were noted to be larger for thinner deposited layer thicknesses. Cette recherche se concentre sur les influences de l'épaisseur de la couche déposée sur les caractéristiques du matériau, la précision dimensionnelle, ainsi que la rugosité de surface de l'acier à outils AISI D2 traité par dépôt d'énergie dirigé par laser (L-DED); tandis qu'on variait l'épaisseur de la couche, on a conservé à des valeurs fixes le reste des paramètres du système L-DED. Après le dépôt au laser, on a évalué les spécimens D2 sans appliquer d'étapes d'usinage subséquentes. On a évalué la précision dimensionnelle des échantillons à la fois par des méthodes de mesure manuelles et des méthodes informatiques, ces dernières utilisant la microscopie confocale à balayage laser (CLSM). Il a été montré que l'augmentation de l'épaisseur de la couche diminuait l'ampleur de la surconstruction de l'échantillon. L'utilisation d'épaisseurs de couche inférieures réduisait la rugosité de la surface supérieure. Cependant, on n'a pas observé d'effet monotone pour la rugosité des surfaces latérales en relation avec l'épaisseur de la couche déposée. De plus, on a évalué les microstructures des échantillons L-DED en utilisant une combinaison de microscopie électronique à balayage (MEB) associée à la spectroscopie de rayons X à dispersion d'énergie (EDS) et la diffraction des rayons X (XRD). On a montré qu'une morphologie dendritique se formait pour les échantillons traités par L-DED, avec une structure de grain en colonne. De plus, la phase cristalline primaire engendrée avec la structure dendritique s'est avérée être de l'austénite. On a noté que les valeurs de dureté par indentation des pièces fabriquées par L-DED étaient plus élevées pour les épaisseurs de couche déposées plus minces.

Directed Energy Deposition on Structurally Low-density Substrate and its Effects on Microstructural and Interfacial Bonding Characteristics

Effect of heat transfer in substrate on microstructure and tensile behavior of deposits built by directed energy deposition

The role of substrate preheating on the microstructure, roughness, and mechanical performance of AISI 316L produced by directed energy deposition additive manufacturing

Effect of ultrasonic vibration on microstructural evolution, clad defects, and surface properties in laser direct energy deposition of Inconel 625

Effect of Substrate Temperature on Bead Track Geometry of 316L in Directed Energy Deposition: Investigation and Regression Modeling

Comparison of properties at the interface of deposited IN625 and mixture of IN625 SS304L by laser directed energy deposition and SS304L substrate

The effects of deposited layer thickness on the material and geometrical properties of L-DED processed AISI D2 tool steel

Integrated Control of Thermal Residual Stress and Mechanical Properties by Adjusting Pulse-Wave Direct Energy Deposition

Effects of lead and lean in multi-axis directed energy deposition

Revealing the Evolution of Microstructure and Mechanical Properties with Deposition Energy and Shielding Gas to Achieve Phase-Balanced Directed Energy Deposition of 2205 Duplex Stainless Steel

Microstructure and crystallographic texture of direct energy deposition printed 316L stainless steel

Interlayer machining effects on microstructure and residual stress in directed energy deposition of stainless steel 316L

Strengthening mechanisms in directed energy deposited austenitic stainless steel

Effects of Laser-Powder Alignment on Clad Dimension and Melt Pool Temperature in Directed Energy Deposition

Influence of Interface on Microstructure and Mechanical Properties of Laser-Direct Energy Deposited Ti60 Alloy

The microstructural evolution and mechanical response of laser direct energy deposition Inconel 718 alloy based on simulation and experimental methods

Pore defects and corrosion behavior of AISI 316L stainless steel fabricated by laser directed energy deposition under closed-loop control

Process-induced Mechanical Property Heterogeneity along the Building Direction of Directed Energy Deposited IN718 Thin-walled Parts

The Effect of Interlayer Delay on the Heat Accumulation, Microstructures, and Properties in Laser Hot Wire Directed Energy Deposition of Ti-6Al-4V Single-Wall

Development of the molten pool and solidification characterization in single bead multilayer direct energy deposition

Directed energy deposition of PH 13–8 Mo stainless steel: microstructure and mechanical property analysis