Abstract:This study investigated how water-soluble extractives of silver birch (Betula pendula Roth) wood interact with the most common adhesives used for producing engineered wood products (EWPs), i.e., melamine-urea-formaldehyde (MUF) and one-component polyurethanes (PUR). Therefore, the extractives were characterized via various chromatographic techniques and mass spectrometry. The effects of extractives on the curing kinetics were investigated using rheometry. The impact of extractives on the chemical and mechanical properties of the cured adhesives was investigated with FTIR spectrophotometry and tensile stress-strain measurements, respectively. Moreover, a comparative study on the shear strength of birch wood with and without extractives was performed. The organic fraction of the water extractives of birch mainly consisted of phenolic glycosides, carboxylic (fatty) acids, and saccharides. The extractives decelerated the curing process of MUF, as observed in a rheological small-angle oscillatory shear experiment using wood substrates as the lower plate. This was indicated by a reduced gel time from 5 to 3.8 h on pristine vs. extracted wood. When measuring MUF on extracted wood, this deceleration was also reached by adding ∼1% (W/W) of the isolated extractives into the MUF resin. Similar experiments with PUR showed a slight acceleration when dispersing extract into the adhesive, indicated by a reduction of vitrification time of −0.9 ± 0.3 h per percent of extractives added. However, measurements with pure PUR on pristine and extracted wood showed no significant difference in curing kinetics due to the extractives’ limited mobility and solubility in PUR. Both PUR and MUF cured adhesive films showed a reduced stiffness, elastic stress limit and tensile strength in uniaxial tensile stress-strain measurements of adhesive films upon increasing the amount of hydrophilic birch extractives concentration. Comparative standard tensile shear strength measurements on pristine and extracted wood indicate a 7–19% strength increase due to extraction when bonding with MUF, while the bond strength of PUR bond lines was less affected by the extraction procedure.

Effects of Heartwood Extractives on Mechanical Properties of Larch

Effects of different incising pretreatments in improving permeability in two refractory wood species

Characterization and Prediction of Mechanical and Chemical Properties of Luanta Fir Wood with Vacuum Hydrothermal Treatment

Colour of larch heartwood and relationships to extractives and brown-rot decay resistance

Extractive distribution in Pseudotsuga menziesii: effects on cell wall porosity in sapwood and heartwood

Compressive Mechanical Properties of Larch Wood in Different Grain Orientations

Effect of thermo-vacuum modification on selected chemical, physical, and mechanical properties of Siberian larch (Larix sibirica L.) wood

Characterization of Larix decidua Mill. (Pinaceae) oleoresin's essential oils composition using GC-MS

Variation in selected mechanical properties of Japanese larch (Larix kaempferi, [Lamb.] Carr.) progenies/provenances trials in Eastern Canada

Contribution of lignin to the strength properties in wood fibres studied by dynamic FTIR spectroscopy and dynamic mechanical analysis (DMA)

Effects of thermal treatment on the mechanical properties of larch (Larix gmelinii) and red oak (Quercus rubra) wood cell walls via nanoindentation

Adhesion-related properties of silver birch (Betula Pendula Roth) wood as affected by hydrophilic extraction

Interactions of hydrophilic birch wood (Betula pendula Roth) extractives with adhesives for load-bearing timber structures

Effects of removal of extractives on the chemical composition and mechanical properties of wood

The influence of extractives on the sorption characteristics of Scots pine (Pinus sylvestris L.)

Measurements of the mechanical properties of larch at elevated and high temperature under nitrogen conditions

Effect of Growth Ring Width and Latewood Content on Selected Physical and Mechanical Properties of Plantation Japanese Larch Wood

Mechanical and morphological bond line properties of silver birch wood pretreated by aqueous extraction

The effect of wood extractives on the thermal stability of different wood species

Structural differences of cell walls in earlywood and latewood of Pinus sylvestris and their contribution to biomass recalcitrance

Short-term hygro-mechanical behaviour of lime wood ( Tilia cordata ) in principal anatomical directions