Abstract:To have a better understand of film cooling technique, many experiments to investigate parameters affecting the film cooling effectiveness and heat transfer have been conducted. In this kind of experiments, different sorts of coolant (CO2, N-2 and etc.) are often applied to match coolant-to-mainstream properties or use some measuring techniques. However, the application of those coolant probably leads to a similarity problem, as the properties of them are different from air coolant in real engine conditions. This study investigates the accuracy of six criteria for the film cooling effectiveness scaling which changes the coolant from air to CO2 based on both experimental and numerical method, to promote the similarity to air coolant of film cooling experiments using CO2 as coolant. The study conducted on the pressure side of 1st stage stator from E-3 aero engine. The mainstream inlet pressure and temperature of the experiment was 112kPa and 312K, respectively. Numerical simulations were conducted by solving the Reynolds Averaged Naiver-Stokes (RANS) equations and Re-Normalization Group (RNG) k-epsilon turbulence model. The effect of CO2 coolant on pressure side film cooling effectiveness was initially investigated, followed by the analysis of the accuracy for six scaling criteria. Finally, reasons leading to the deviation of scaling was studied. Both numerical and experimental results indicate that the application of CO2 coolant leads to an obvious reduction of eta(APS) at relatively low coolant mass flow rate. That effect almost disappears at high coolant mass flow rate. In the experiment, eta with the variation in VR has the highest Pearson correlation coefficient (R-p) between air and CO2 coolant at almost all measuring points on pressure side, illustrating VR criterion has the highest accuracy in the scaling which the coolant is changed from air to CO2. The cooling effectiveness deviation of VR criterion is lower than 3% at all coolant CO2 percentage(obtained from CFD results). The low specific heat capacity of CO2 will lead to a relatively faster decay of injection temperature compared with air, producing an adverse influence on cooling effectiveness. The high density of CO2 can increase attachment ability of injections(especially on mid-span of the blade) and form a similar cooling film state to the air coolant at higher coolant mass flow rate. The results of this study can be used to promote the accuracy of the experiment using CO2 as coolant at relatively low temperature conditions in terms of film cooling effectiveness and injection state(attachment or separation). (c) 2021 Elsevier Ltd. All rights reserved.

Comparison of using air, CO2 and helium for the cooling of square-shaped electronic parts: CFD study with entropy generation analysis

Numerical Study on the Working Performance of a G-M Cryocooler with a Mechanically Driven Displacer

Analytical Modeling of Forced-Air Cooling Heatsink by Considering Air Temperature Rise in Channel and Coupling of Multiple Heat Sources

Active cooling of hot integrated circuits using a rotating cylinder and NEPCM-water mixture: Numerical analysis of the impact of phase change and Magnetohydrodynamics on double-diffusive mixed convection

Numerical simulation of microchannel heat exchanger using CFD

A Comparative Numerical Analysis of Cold Plates for Thermal Management of Chips With Hotspots

The optimum computational simulation of MHD natural convection for improved cooling efficiency and entropy performance inside Ϻ-shaped cabinet

Study on Forced Air Convection Cooling for Electronic Assemblies

Three-dimensional fluid-thermal–mechanical coupling numerical modeling of elastocaloric cooler for electronic chip

Numerical investigation of the effect of thermophysical properties of liquids on convective heat transfer in devices

Numerical and Experimental Study of Scaling Criteria Accuracy for Film Cooling Using CO2 Coolant

A computational fluid dynamics study by conjugate heat transfer in OpenFOAM: A liquid cooling concept for high power electronics

Numerical Investigation on Thermal Performance of Two-Phase Immersion Cooling Method for High-Power Electronics

Numerical and Experimental Investigations of Electronic Evaporative Cooling Performance with a Coiled Channel

Experimental And Numerical Study On Natural Air Cooling Of A Remote Radio Unit

Comparison of the Effect of Five Different Entrance Channel Shapes of a Micro-Channel Heat Sink in Forced Convection with Application to Cooling a Supercomputer Circuit Board

Numerical evaluation on the heat dissipation capability of liquid metal based chip cooling device

Numerical Simulation of a Novel Energy-Efficient Dew-Point Evaporative Air Cooler

Thermal Modeling and Comparative Analysis of Jet Impingement Liquid Cooling for High Power Electronics

Numerical Study of Condensation Heat Transfer Performance and Liquid Film Distribution Characteristics in Small-Scale Helium Liquefiers

Experimental and numerical investigation on thermoelectric coolers for comparing air-to-water to air-to-air refrigerators