Abstract:Clarifying the influences of anchorage parameters on rock mass deformation and failure under impact dynamic load is the key to the control of surrounding rock in rock burst roadways. However, the existing research mainly focuses on the influence of anchorage parameters on rock mass deformation and failure under static load. However, the research on the dynamic failure mechanism of rock mass remains insufficient. According to the deformation and failure characteristics of anchor structure in practical engineering, the dynamic response law of the anchored rock mass under lateral impact load was studied through indoor similar physical model tests. Besides, the effects of anchor material, prestress and anchorage method on crack propagation mode and dynamic mechanical characteristics of anchored rock mass were analyzed. The lateral impact mechanical model of the anchored rock mass was established. Furthermore, rational suggestions on anchorage support in deep rock burst roadways were put forward based on the impact failure mechanism of prestressed anchored rock mass. The following research results were yielded: Under impact load, the cracks of the anchored rock mass are concentrated around the impact point, and the rock sample mainly undergoes shear failure and tensile failure. The size of cracks is controlled by the anchor material, the anchoring method and the prestress level. The axial force of the bolt increases with the increase of steel strength. The axial force platform segments of HRB400, HRB500, and CRM700 bolts are 20.84kN, 20.95kN, and 45.65kN, respectively. The material of the bolt has a significant impact on the impact resistance of the rock mass. The high strength of the bolt increases the stiffness of the anchored rock mass, and the impact force and axial force of the bolt are more sensitive to the impact load. When the pre-stress of the bolt increases from 15 to 45kN, the impact force action time decreases from 47 to 16ms, and the impact force platform value increases from 24.54 to 30.60kN. The impact force change is not significant, but the impact force action time changes more significantly. High pre-stress can improve the deformation resistance of the rock mass, but it will reduce the bearing capacity and impact resistance of the anchor structure. There is also a significant difference in the axial force of the bolt between the full length anchoring and end anchoring methods. The axial force of the bolt under the full-length anchoring method shows a slow increasing trend, and the axial force of the bolt under end anchoring is similar to its static load mechanical characteristic curve. compared with end anchorage, the rock mass is of greater stiffness and deforms less severely under full-length anchorage; meanwhile, the bolt can absorb massive energy through its elongation, but it tends to break under dynamic load. For deep rock burst roadways, it is suggested to choose "three-high" bolts (cables) as the supporting material, reduce the dynamic and static loads of surrounding rock and improve the mechanical properties of surrounding rock, to weaken the influence of dynamic load on the supporting structure of the anchored surrounding rock. The research results provide some theoretical guidance for the design of anti-burst bolt support in deep rock burst roadways.

A Numerical Model for the Bearing Capacity of Anchoring Interface in Composite Rock Mass by A Modified Nonlinear Bond-Slip Model

Models to Predict Shear Resistances of Anchor Bolts

Centrifuge Modelling of Suction Anchor Subjected to Inclined Load in Soft Clay

Numerical Simulation of the Interfacial Behaviour of Grouted Rockbolts in Tunnel Support Based on a Tri-Linear Bond-Slip Model

Strength and Failure Behaviors of a Jointed Rock Mass Anchored by Steel Bolts: A Numerical Modeling Study

Analytical studying the axial performance of fully encapsulated rock bolts

Laboratorial Tests and Numerical Modeling of Rock Bolts Bonded by Different Materials

Coupling model of jointed rock mass and rock bolt in offshore LPG underground storage

Tensile Bearing Performance and Mechanical Transfer Mechanism of Coal-Rock Composite Anchor Bodies Under Different Height Ratios of Rock to Coal

A novel constitutive law of confined grouted rock bolt under pull-out load based on a fully nonlinear bond-slip model

Mechanical Behaviour of Anchored Rock Containing Weak Interlayer under Uniaxial Compression: Laboratory Test and Coupled DEM–FEM Simulation

Coupling Rheological Behavior of Rock Mass Supported with Rockbolts Based on the Point Load Model

Study on reasonable anchorage length based on failure mechanism of the bolt anchorage system

An analytical analysis of the full-range behaviour of grouted rockbolts based on a tri-linear bond-slip model

Bearing Characteristics of Surrounding Rock of Deep Mining Roadway with Full and End Bolt Anchorages: A Comparative Numerical and Experimental Study

Experimental and Data-Driven Prediction for the Impact of Free/bond Lengths of Element Specimen on Interface Characterization of Ground Anchors

Shear behaviour of anchored jointed rock mass under different engineering conditions considering damage and joint surface morphology

In-Situ Test and Numerical Simulation of Anchoring Performance of Embedded Rock GFRP Anchor

Experimental study on lateral impact resistance of the prestressed anchored rock mass

State-of-the-art on the anchorage performance of rock bolts subjected to shear load

Study on the Force Transfer Process of Bolt–Slurry Interface of Full-Length Bonding Anchor System at Earthen Sites