Abstract:Lithium–sulfur (Li–S) batteries are severely hindered by the low sulfur utilization and short cycling life, especially at high rates. One of the effective solutions to address these problems is to improve the sulfiphilicity of lithium polysulfides (LiPSs) and the lithiophilicity of the lithium anode. However, it is a great challenge to simultaneously optimize both aspects. Herein, by incorporating the merits of strong absorbability and high conductivity of SnS with good catalytic capability of ZnS, a ZnS-SnS heterojunction coated with a polydopamine-derived N-doped carbon shell (denoted as ) with uniform cubic morphology was obtained and compared with the ZnS-SnS2@NC heterostructure and its single-component counterparts ( and SnS2@NC). Theoretical calculations, ex situ XANES, and in situ Raman spectrum were utilized to elucidate rapid anchoring-diffusion-transformation of LiPSs, inhibition of the shuttling effect, and improvement of the sulfur electrochemistry of bimetal ZnS-SnS heterostructure at the molecular level. When applied as a modification layer coated on the separator, the cell with optimized lithiophilicity and sulfiphilicity enables desirable sulfur electrochemistry, including high reversibility of 1149 mAh g–1 for 300 cycles at 0.2 C, high rate performance of 661 mAh g–1 at 10 C, and long cycle life with a low fading rate of 0.0126% each cycle after 2000 cycles at 4 C. Furthermore, a favorable areal capacity of 8.27 mAh cm–2 is maintained under high sulfur mass loading of 10.3 mg cm–2. This work furnishes a feasible scheme to the rational design of bimetal sulfides heterostructures and boosts the development of other electrochemical applications.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsnano.1c00270?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsnano.1c00270</a>.Additional experimental sections (materials synthesis, characterizations, and DFT calculations); SEM, TEM, XRD, TG, XPS, BET, and XANES characterizations of the samples; CV curves; discharge–charge profiles and cycle performance of various electrodes; in situ Raman tests; optimized geometries of LiPSs; Tables S1–S6: Li+ diffusion rates, EIS fitting, and comparisons of electrochemical performance (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.1c00270/suppl_file/nn1c00270_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Nano high-entropy alloy with strong affinity driving fast polysulfide conversion towards stable lithium sulfur batteries

High-Entropy Alloy Electrocatalysts Bidirectionally Promote Lithium Polysulfide Conversions for Long-Cycle-Life Lithium-Sulfur Batteries

High‐Entropy Catalysis Accelerating Stepwise Sulfur Redox Reactions for Lithium–Sulfur Batteries

High Entropy Alloy Nanoparticles Dual-Decorated with Nitrogen-Doped Carbon and Carbon Nanotubes As Promising Electrocatalysts for Lithium-Sulfur Batteries

Modifying Electron Structure of FeCoNiZnCu High-Entropy Alloy with Introduction of Cu for Facilitating the Catalytic Effect in Lithium Sulfur Batteries

Superior-Performance Lithium-Sulfur Battery: Face-Centered-Cubic-Structure High-entropy Alloy Improves the Bidirectional Catalytic Conversion of Polysulfide/Sulfide

Modifying the electron structure of an FeCoNiZnCu high-entropy alloy with the introduction of Cu to facilitate the catalytic effect in lithium sulfur batteries

High-entropy perovskite oxide nanofibers as efficient bidirectional electrocatalyst of liquid-solid conversion processes in lithium-sulfur batteries

Atom-dominated relay catalysis of high-entropy MXene promotes cascade polysulfide conversion for lithium–sulfur batteries

ZnS-SnS@NC Heterostructure as Robust Lithiophilicity and Sulfiphilicity Mediator toward High-Rate and Long-Life Lithium–Sulfur Batteries

High‐Entropy Alloys to Activate the Sulfur Cathode for Lithium–Sulfur Batteries

Fast conversion and controlled deposition of lithium (poly)sulfides in lithium-sulfur batteries using high-loading cobalt single atoms

High-entropy Sulfides Enhancing Adsorption and Catalytic Conversion of Lithium Polysulfides for Lithium-Sulfur Batteries

High-Entropy Metal Nitride Embedded in Concave Porous Carbon Enabling Polysulfide Conversion in Lithium-Sulfur Batteries

A High-Entropy Metal Oxide As Chemical Anchor of Polysulfide for Lithium-Sulfur Batteries

In-situ Construction of an Alloy Hybrid Interface and Ultrathin ZnS Nanosheets Catalyst for Polysulfide by Trifunctional ZnI 2 Electrolyte Additive for Li-S Batteries

Synergistic effect of Li2S@Li3PS4 nanosheets and MXene for high performance lithium-sulfur batteries

An Entangled Cobalt–Nitrogen–Carbon Nanotube Array Electrode with Synergetic Confinement and Electrocatalysis of Polysulfides for Stable Li–S Batteries

Tuning Dual-Atom Mediator Toward High-Rate Bidirectional Polysulfide Conversion in Li-S Batteries

Enhanced Catalytic Conversion of Polysulfides Using Bimetallic Co7Fe3 for High-Performance Lithium-Sulfur Batteries

Synergistic effect of Co3Fe7 alloy and N-doped hollow carbon spheres with high activity and stability for high-performance lithium-sulfur batteries