Abstract:The recently developed tough and self-healing hydrogels, containing a large number of physical bonds, have found widespread applications in bioengineering and soft electronics. Owing to the sophisticated physical interactions and organization, these hydrogels often demonstrate structural heterogeneities, which strongly influence their mechanical performances. Using poly(N,N-dimethyl acrylamide-co-methacrylic acid) hydrogels (P(DMAA-co-MAAc)) with dynamic hydrogen bonds (H-bonds) as a model system, the structural characterization has been carried out in this study using small-angle X-ray scattering (SAXS) and small-angle neutron scattering (SANS) analyses, along with exploring the influence of the structure on the mechanical properties. By systematically tuning the polymer composition, including the monomer fraction and chemical cross-linking density, two different hydrogel regions with distinct mechanical properties were observed: the swollen regions and shrunk regions. The former was mechanically weak, whereas the latter exhibited a tough behavior. Both types of hydrogels were noted to be highly heterogeneous, which results from the nanoscale spatial polymer concentration fluctuations at ∼100 nm scale. Combined with the contrast variation utilizing SANS, the structure parameters, including the polymer volume fraction of the dense and sparse regions, volume fraction occupied in the space, and average correlation length of the long-range and short-range heterogeneous structures, were explored using a scaling model based on a two-phase system composed of the densely and sparsely cross-linked regions. Using in situ SAXS, the microscopic deformation of the tough and shrunk hydrogels was noted to follow the affine deformation, while a significantly non-affine deformation was observed in the swollen hydrogels, which might have led to the different mechanical performances of these materials.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.macromol.1c01064.Swelling volume ratio of hydrogels 0.14-0.2% during the drying–swelling cycle (Figure S1); FT-IR spectra of PDMAA, PMAAc, and P(DMAA-co-MAAc) and temperature dependence of FT-IR spectrum of P(DMAA-co-MAAc) (Figure S2); semi-empirical quantum chemical calculations for revealing the conformation features and their interaction in water (Figure S3); tensile stress–strain curves of P(DMAA-co-MAAc) hydrogels f-0.1% with various f values (0.12, 0.13, and 0.15) and P(DMAA-co-MAAc) hydrogels 0.14-x with various x values (0.05, 0.1, and 0.15%) (Figure S4); 1D scattering intensity as a function of the scattering vector q under various stretch ratios for the hydrogels f-0.1% with the molar fraction of DMAA varying from 0.12 to 0.15 and hydrogels 0.14-x with the chemical cross-linking density ranging from 0.05 to 0.15% (Figures S5 and S6); stretch-induced structure evolution of the swollen hydrogel 0.14-0 (Figure S7); tensile stress–strain curve of hydrogel 0.14-1% and the corresponding Mooney–Rivlin plot (Figure S8); and structural parameters of the swollen and shrunk hydrogels (Table S1) (PDF)This article has not yet been cited by other publications.

Assessment of three-dimensional large-scale deformations during drying of hydrogels via a structure from motion photogrammetry

Dimethyl Sulfoxide Mediated High-Fidelity 3D Printing of Hydrogels

Slippery Hydrogel with Desiccation-Tolerant ‘skin’ for High-Precision Additive Manufacturing

Photo-crosslinking speckle patterns for large deformation measurement of hydrogels using digital image correlation

Microstructure and Full-Field Deformation Measurement of Compound Porous Hydrogels Using Digital Speckle Correlation Method

Micro/nanofabrication of Brittle Hydrogels Using 3D Printed Soft Ultrafine Fiber Molds for Damage-Free Demolding.

Modeling Mass Transport Dynamics in Deformable Hydrogels during Evaporation

A Digital Volume Correlation Technique for 3-D Deformation Measurements of Soft Gels

Application of Digital Image Correlation (DIC) to the Measurement of Strain Concentration of a PVA Dual-Crosslink Hydrogel Under Large Deformation

The potential of Brillouin Spectroscopy for investigating the mechanical properties of hydrogels during dehydration

Modeling and Simulation of Swelling Behavior of Thermosensitive Hydrogels

Rate-dependent fracture of hydrogels due to water migration

Drying of agarose gels monitored by in-situ interferometry

Tough Hydrogels with Dynamic H-Bonds: Structural Heterogeneities and Mechanical Performances

Scaling laws to predict humidity-induced swelling and stiffness in hydrogels

Sequentially Controlled Deformations of Patterned Hydrogels into 3D Configurations with Multilevel Structures.

Characterizing hydrogel behavior under compression with gel-freezing osmometry

High-strain sensitive zwitterionic hydrogels with swelling-resistant and controllable rehydration for sustainable wearable sensor

Mechanical properties soft hydrogels: assessment by scanning ion-conductance microscopy and atomic force microscopy

Centrosymmetric 3D Deformation Measurement Using Grid Method with a Single-Camera

Molecular dynamic simulations of the water absorbency of hydrogels