Abstract:The advent of new materials and technologies in building materials has changed the way of building. New lighter materials with easier application methods and improved mechanical behaviors, have become necessary for the market. Moreover, the new environmental policy (2022) aims to transform the waste management into sustainable materials management to ensure the long-term protection and improvement of the environment. For the brick and tile industry, raw materials and the additives that compose the product mixture seem to be a key factor in this direction. Furthermore, every product type (solid or perforated brick) requires different additives to achieve the properties that are postulated by the international standards. For the study, the wide range of additives that were used have been assorted into three (3) categories: the inert materials, the lightweight materials, and the industrial remains. Totally, eight (8) different materials were used as additives into ceramic mass, in different proportions each time. Almost all additives used for this research were pore-forming agents. These burn out almost completely before reaching the full-fire temperature, and do not change the fired body. As a result of additives burnt out, the necessary pore volume is formed in the fired brick body, which, if combined with an appropriate percentage of voids, result in raw density readings. The pore structure is significant as long as the ultimate strength of lightweight bricks is acceptable. In this study, additives between 3 and 25% by weight were added to the clay mixture. The extrusion of specimens in solid form was carried out using the Laboratory’s vacuum press. Firstly, the extrusion of specimens from the original raw material was implemented. Secondly, it was made on the material mixed with the additives mentioned above. A series of experimental activities were followed to determine the variations of the mechanical and physical properties as well as their production procedures (extrusion, drying, and firing). According to five (5) key properties measured in the current study and compared with the mixture without additives, it was found that the variation in thermal conductivity improvement is between -11% and 19%. The bending strength of the fired products showed a decrease from 16% to 55% except for the addition of bauxite residue, which increased the strength by 8%. Bigot drying sensitivity decreased from 11% to 27%. The density in two cases increased from 2% to 7% while in the majority the mixtures with the additives showed a decrease in density from 1% to 14%. Finally, the addition of the necessary water for shaping during extrusion showed a variation from a 10% decreased to a 14% increased water.

Shortening of fast firing in the ceramic tile production by inorganic additives - an upscale to the industry

Efficient Recovery of Solid Waste Units as Substitutes for Raw Materials in Clay Bricks

Impact of Nanoparticle Additions on Life Cycle Assessment (LCA) of Ceramic Tiles Production

The Effect of a Carbon Additive on Compaction of Partially Stabilized Zirconia Powders upon Pressing and Sintering

Effect of Non-Plastic Raw Materials Particle Size on Technological Properties of the Single-Fired Wall Tile Bodies

PREPARATION AND APPLICATION OF CERAMICS FIRING ADDITIVE

The effects of fine fire clay sanitaryware wastes on ceramic wall tiles

Performance enhancing of porcelain insulators using low cost micro additives

Influence of additives and binder on the physical properties of dental silicate glass-ceramic feedstock for additive manufacturing

Effect of additives on sintering of zirconia ceramics

Enhancing 3D printed ceramic components: The function of dispersants, adhesion promoters, and surface-active agents in Photopolymerization-based additive manufacturing

Investigation of the effects of kiln roller waste addition on porcelain tile matte-opaque glazes

Experimental Investigation on Feasibility of utilizing Phosphogypsum in E-Glass Fiber-incorporated Non-fired Ceramic Wall Tile

Recycling of glass waste in ceramics—part I: physical, mechanical and thermal properties

Glazing effect for producing environmentally friendly ceramics for cladding applications

Evaluating pumice as a sustainable raw material in porcelain tile production: impact on technical properties

Modification of a Ceramic Brick Additives of Inorganic Technogenic Products of Water Treatment of Combined Heat and Power Plant

Enhancing thermal properties and surface quality of lappato glazed porcelain tiles through milling time optimization

Comparative analyses of the IV group oxides additives influence on the sintering kinetics of zirconia nanopowders

Effects of Additives on the Interfacial Microstructure of Cofired Electrode‐Ceramic Multilayer Systems

Study of the operative conditions and the optimum amount of municipal incinerator bottom ash for the obtainment of ceramic floor tiles