Abstract:This investigation considered the usability of ceramic waste powder (CWP) in altered quantities in reinforced concrete beams (RCBs). In this way, it was aimed to reduce the environmental impacts of concrete by using CWP as a raw material in RCBs. 12 small-scale shear RCBs with the dimensions of 100 × 150 × 1000 mm were tested in this study. The variations of stirrups spacing and CWP ratio were examined in these specimens. The percentages of CWP by weight utilized in RCBs were 10%, 20%, and 30%, and stirrups spacings were adopted as 270 mm, 200 mm, and 160 mm. At the end of the study, it was determined that more than 10% CWP additive negatively affected the RCBs' compressive strength. The load-carrying capacity reduced between 30.3% and 59.4% when CWP increased from 0% to 30% as compared to RCB with stirrups spacing of 270 mm without CWP. However, compared to RCB with stirrups spacings of 200 mm and 160 mm without CWP, there were decreases in the load-carrying capacity as 21.4%–54.3% and 18.6%–54.6%, respectively. While the CWP ratio increased, the specimens with 160 mm, 200 mm, and 270 mm stirrups spacings obtained a lower maximum load value. However, with the increase of the CWP ratio in the specimens with 160 mm stirrups spacing, RCBs reached the maximum load-carrying capacity at an earlier displacement value. When stirrups spacing was selected as 270 mm, it was observed that the maximum load-carrying capacity of RCBs reached at a similar displacement value as the CWP ratio increased. Besides, it was resulted that the bending stiffness of RCBs reduced as the quantity of CWP enhanced. The bending stiffness decreased by 29.1% to 66.4% in the specimens with 270 mm stirrups spacing, 36.3% to 20.2% with 200 mm stirrups spacing, and 10.3% to 36.9% with 160 mm stirrups spacing. As an implication of the experiments, the use of CWP up to 10% in RCBs was realized as an economical and environmental approach and is suggested. There is some evidence to report that making use of CWP may be considered to be ecologically benign. This is due to the fact that reusing CWP may significantly reduce CO 2 emissions, save energy, and reduce total power consumption. Furthermore, the experimental results were compared to the analytical calculations.

Ductility and strength of reinforced concrete beams strengthened with aluminum CNC waste

Improvement in Bending Performance of Reinforced Concrete Beams Produced with Waste Lathe Scraps

Influence of ceramic waste powder on shear performance of environmentally friendly reinforced concrete beams

Investigation on Improvement in Shear Performance of Reinforced-Concrete Beams Produced with Recycled Steel Wires from Waste Tires

Feasibility of using aluminum alloy bars as near‐surface mounted reinforcement for flexural strengthening of reinforced concrete beams

Strengthening of Reinforced Concrete Beams with Textile-Reinforced Concrete

Shear Improvement of Defected RC Beams with Sustainable Aluminum Boxes Incorporating High Performance Concretes

Shear and flexural strength of reinforced concrete beams made with recycled coarse aggregate concrete

Performance Assessment of Fiber-Reinforced Concrete Produced with Waste Lathe Fibers

Experimental and Numerical Investigation of the Flexural Behavior of Reinforced-Concrete Beams Utilizing Waste Andesite Dust

Behavior of reinforced concrete ring beams strengthened with sustainable materials

Mechanical behavior in terms of shear and bending performance of reinforced concrete beam using waste fire clay as replacement of aggregate

A preliminary study on the development of the normal concrete-UHPC composite beam via wet casting

Experimental Investigation of Properties of Concrete Containing Recycled Construction Wastes

Use of recycled coal bottom ash in reinforced concrete beams as replacement for aggregate

Flexural behaviour of recycled reinforced concrete beams strengthened/ repaired with CFRP laminates

Stiffening Performance of Cold-Formed C-Section Beam Filled with Lightweight-Recycled Concrete Mixture

Experimental and Numerical Evaluation for Hybrid Reinforced T-Beam with Different Ratios of Recycled Rubberized Concrete

Influence of shear strengthening of reinforced normal concrete beams incorporating sustainable materials

The shear and flexural behavior of cold-formed steel composite I and U beams

Using ultra-high performance fiber reinforced concrete in improvement shear strength of reinforced concrete beams