Abstract:To meet the demands of both processing and serving, to the best of our knowledge, this is the first report exhibiting large range control of the yield ratio from 0.31 to 0.96 with decent elongations over 10% in the same alloy with low-cost thermal treatments. The yield ratio of the metastable Ti-30Zr-5Mo alloy was regulated via adjusting trigger stress of the stress-induced phase transformation and work-hardening ability through changing the α phase content. Materials with acicular α phase of different contents were successfully prepared via low-cost thermal treatment. The effects of the α phase content on the stress-induced α ' martensite phase transformation and work hardening behavior were then investigated. In the Ti-30Zr-5Mo alloy with dual phases, due to the crystal difference and element partitioning, the hardness of the α phase is higher than that of the β matrix, and the hardness difference between the phases increases with increasing α phase. In addition to Mo, Zr plays an important role in stabilizing the β phase in high-Zr-containing alloys. Deformation initiates in the β phase of both single-phase and duplex-phase alloys. The deformation mechanism of the β phase is dependent on both the β domain and β stability. Due to the low trigger stress and excellent work hardening ability, stress-induced α ' martensite phase transformation is helpful to lower the yield ratio. As the α phase content increases, the trigger stress increases, and when the α phase content increases to 40%, dislocation slip dominates rather than stress-induced α ' martensite phase transformation, and a high yield strength of 944 MPa is obtained. The α/β phase interfaces act as effective obstacles to hinder dislocation movement and provide working hardening, and the obstruction effect is more significant with an increase in the hardness difference between the α and β phases. The stress-induced α ' phase transformation and/or the deformation coordination between the α and β phases guarantee decent elongations of no less than 10% in the large control of the yield ratio from 0.31 to 0.96 with a yield strength from 254 to 1013 MPa. It paves the way to develop "Unititaniam" alloys for wide possible applications.

Coherent ω phase induced yield strength improvement in Ti-19Nb-1.5Mo-4Zr-8Sn alloy

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

The role of the ω phase on the microstructure evolution of precipitation and mechanical property in Ti-3Al-5Mo-4Cr-2Zr-1Fe

Mechanical properties and deformation mechanisms of Ti-15 Nb-5Zr-4Sn-1Fe alloy with varying α phase fraction

Electron Beam Welding and Post Heat Treatment of a New Near-Beta High-Strength Ti-4Al-5Mo-5V-5Cr-1Nb Alloy

A strategy to regulate the yield ratio of a metastable high Zr-containing β titanium alloy: Synergistic effects of the β domain, β stability and β/α interfaces by varying the α phase content

Natural aging of a metastable β-type titanium alloy to simultaneously enhance yield strength and uniform elongation

Precipitation behavior and strengthening-toughening mechanism of hot rolled sheet of Ti65 titanium alloy during aging process

Cold Rolling Deformation Characteristic of a Biomedical Beta Type Ti–25Nb–3Zr–2Sn–3Mo Alloy Plate and Its Influence on α Precipitated Phases and Room Temperature Mechanical Properties During Aging Treatment

Heterogeneous distribution of isothermal ω precipitates prevents brittle fracture in aged β-Ti alloys

Enhanced Mechanical Properties of Ti-5Al-5Mo-5V-3Cr-1Zr by Bimodal Lamellar Precipitate Microstructures Via Two-Step Aging

α" martensite engineering: A strategy to achieve high yield strength and low yield ratio synergy for dual-phase titanium alloy

Phase precipitation behavior and tensile property of a Ti–Al–Sn–Zr–Mo–Nb–W–Si titanium alloy

Improved mechanical properties of W-Zr-Ti-Nb alloys via adding Ti and Nb

Achieving super-high strength and acceptable plasticity for a near β-type Ti-4.5Mo-5.1Al-1.8Zr-1.1Sn-2.5Cr-2.9Zn alloy through manipulating hierarchical microstructure

Formation of intermediate phases and their influences on the microstructure of high strength near-β titanium alloy

Minor additions of Sn suppress the omega phase formation in beta titanium alloys

Microstructure Evolution and Phase Transformations in Ti-22Al-25Nb Alloys Tailored by Super-Transus Solution Treatment

Correspondence of the aging behaviors and the phase constituents of the Ti-Mo-based alloys tailored by the Al and Zr additions

Effect of Deformation Temperature on the Microstructure and Texture Evolution of Ti-6Al-4Zr-2Mo-6V Alloy

Enhancement of {110} Texture by Controlling α‐phase and Achievement of Low Young's Modulus and High Strength in Metastable β‐type Ti–Zr‐Based Alloys