Modeling Corrosion in Suspension Bridge Main Cables

E. Karanci

DOI: https://doi.org/10.7916/D8RB7H05

Abstract:Modeling Corrosion in Suspension Bridge Main Cables

Engineering,Materials Science

What problem does this paper attempt to address?

Corrosion-Fatigue Analysis of Wires in Bridge Cables Considering Time-Dependent Electrochemical Corrosion Process

He Zhang,Linjie Yao,Xianglong Zheng,Mingjiang Shen,Xu Xie

DOI: https://doi.org/10.1061/jenmdt.emeng-6806

2023-01-01

Journal of Engineering Mechanics

Abstract:Environmental corrosion and cyclic dynamic loadings are the main causes of cable failures. In the degradation process of cables, the effects of corrosion and cyclic loading are coupled and the corrosion rate is time dependent. To consider the time-variant properties of the electrochemical corrosion process, the evolution curve of corrosion current density was proposed and introduced into a corrosion-fatigue model. Based on the model, we extracted in situ wires from a tied-arch bridge for the corrosion-fatigue analysis. The surface profiles of the wires from midregion and the anchored region were measured. We found that the corrosions in the anchored region of the wires distribute more uniformly than those in the midregion due to the different contact patterns among wires. And the corrosion characteristics of salt spray-corroded wires are close to those of wires from the anchored region. The corrosion-fatigue simulations considering the effect of environments, loadings, and contact patterns of wires show that the failure modes of wires are greatly affected by loadings; the lifetimes of wires and cables are particularly sensitive to environmental corrosivity; and due to different contact patterns, the lifetimes of cables from the midregion are shorter than those from the anchored region by 30%. The research on corrosion fatigue of cables provides a rational basis for the operation and maintenance of cable-supported bridges.
Estimation model for steel wire crack propagation and its application in calculation of pre-corrosion fatigue life

Zheng Xianglong,Xie Xu,Li Xiaozhang,Qian Liqin,Shen Yonggang

DOI: https://doi.org/10.15951/j.tmgcxb.2017.03.012

2017-01-01

Abstract:To provide practical parameters of crack propagation model for damage tolerance analysis of bridge cable steel wires,fatigue threshold (ΔKth) and data in crack propagation calculation were censused according to relevant experimental results of different kinds of steel.An empirical model suitable for different yield strength and stress ratios was established.Based on the proposed model,a method was proposed to predict the fatigue life of corroded steel wires according to the one-dimensional crack growth hypothesis.In addition,an example was given to analyze the fatigue life of corroded wires under constant-amplitude and variable-amplitude fatigue loads.The results show that the correlation between yield strength and fatigue threshold of pearlitic steel increase with the stress ratio.The crack propagation model and the proposed initial crack depth hypothesis can well simulate the fatigue discreteness and endurance limit property under constant-amplitude load.The results of fatigue assessment of corroded wires under variable-amplitude loads are very sensitive to the fatigue threshold.However,the residual life predicted by conservative threshold indicates that,steel wire cables with slight corrosion can serve normally during routine inspection period if the maintenance is conducted in time.
Probability-Based Performance Degradation Model and Constitutive Model for the Buckling Behavior of Corroded Steel Bars

Weipeng Weng,Xu Xie,Yanyun Lei

DOI: https://doi.org/10.3390/su15097532

IF: 3.9

2023-01-01

Sustainability

Abstract:The corrosion of steel bars significantly influences the safety running of concrete bridges. The current bridge design code always ignores the changes in mechanical properties of the materials during their service life which results in an overestimation of the seismic capacity of concrete bridges Therefore, a hysteretic constitutive model that considers the influence of reinforcement corrosion is necessary. This study established a probability-based model for the mechanical property degradation of corroded steel bars using statistical analysis to estimate the mechanical properties under specific corrosion rates. The validity of the proposed degradation model was verified by a series of monotonic tensile tests on corroded steel bars. Moreover, a constitutive model of corroded steel bars based on the Reinforcing Steel Model in OpenSees was obtained. This model considers the influence of corrosion on the slenderness ratio, yield strength, ultimate strength, and elongation. A comparison with the experimental data demonstrated the accuracy of the proposed model. The proposed model is straightforward because its parameters can be predicted using existing research data. The proposed model can provide a basis for the seismic performance evaluation of corroded reinforced concrete (RC) members.
Experimental Study and Residual Performance Evaluation of Corroded High-Tensile Steel Wires

Xianglong Zheng,Xu Xie,Xiaozhang Li

DOI: https://doi.org/10.1061/(asce)be.1943-5592.0001114

2017-01-01

Journal of Bridge Engineering

Abstract:To evaluate the residual service performance of corroded high-tensile steel wires, a batch of in situ wires that had served for 13 years in the hangers of an arch bridge was investigated. Four types of corroded wires were derived from the in situ wires by placing them in the indoor environment for 1.5 years (Type A) or treating them in an alternate dry-wet environment for 0.25-1.5 years (Types B, C, and D). The mechanical properties of the corroded wires were investigated with tensile and fatigue tests, and the fracture characteristics were observed. Fatigue tests on Type A wires with different stress ranges were conducted, and the stress intensity factor range Delta K-p at the bottom of crack-initiation pits was analyzed. According to the S-N curve for Type A wires, the crack-propagation characteristics of steel wires were investigated. The linear elastic fracture mechanics (LEFM) approach was used to predict the residual life of corroded wires in two systems of arch bridges. The tests show that the ultimate strain of corroded wires decreased with an increase in degree of corrosion. The fatigue properties of wires were found to degrade significantly at the early corrosion stage, and the degradation rate slowed down with further development of corrosion. The correlation between the fatigue life and the stress intensity factor range DKp at the bottom of corrosion pits shows that larger pitting size tended to have shorter life under the same stress range, and fatigue cracks were difficult to initiate at the corrosion pits below the fatigue threshold. The crack-growth parameters of the Paris law identified from the S-N curve of Type A wires were m = 2.87, C = 8 x 10(-12) under the stress ratio R = 0.5. The residual life predicted by LEFM shows that in a dry environment, corroded wires with an initial pitting depth of 0.6 mm can serve for more than 30 years in arch-beam combination-system bridges, whereas they can only serve for 5 years in floating-system arch bridges.
Effect Of Corroded Surface Morphology On Ultra-Low Cycle Fatigue Of Steel Bridge Piers

Fangyuan Song,Tingting Zhang,Xu Xie

DOI: https://doi.org/10.3390/ma14030666

IF: 3.4

2021-01-01

Materials

Abstract:Corrosion is a common form of durability degradation of steel bridges. Corrosion morphology affects stress distribution under cyclic loads and causes strain concentrations in pits, thus affecting the mechanical properties of steel structures, including ultra-low cycle fatigue (ULCF). To precisely simulate corrosion morphology and investigate the ULCF failure mechanism of corroded steel piers, a sculpting method was applied to mesh units using three-dimensional surface morphology data of corroded steel specimens. Moreover, the ULCF crack-initiation life was numerically predicted using the finite element model based on the cyclic void growth model (CVGM). The cumulative equivalent plastic strain, cyclic void growth index, and critical void growth index of corroded steel piers with different corroded morphologies were compared. Results reveal that, regardless of whether the pier is corroded, fatigue cracks tend to initiate at the weld toe at corners when exposed to cyclic loads under an oblique direction at the pier top. Additionally, the ULCF crack-initiation life in a corroded pier is less than that in an uncorroded pier, and it is significantly affected by a reduction in the pier wall thickness. Corrosion pits affect the position of ULCF crack initiation in a steel pier and cracks tend to initiate at the bottom of pits with large depth-to-diameter ratios. In the case of minor corrosion, the corrosion morphology affects the seismic performance of piers to a small extent.
Simplified Structural Deterioration Model for Reinforced Concrete Bridge Piers under Cyclic Loading 1

Anirudh S. Rao,Michael D. Lepech,Anne S. Kiremidjian,Xiao-Yan Sun

DOI: https://doi.org/10.1080/15732479.2016.1198402

2017-01-01

Structure and Infrastructure Engineering

Abstract:Deterioration due to reinforcement corrosion represents a significant cause of damage to reinforced concrete bridges all over the world. Although numerous studies have identified the substantial influence that corrosion can have on the failure of concrete structures under seismic loads, there has been comparatively less work done on the modelling of structural vulnerability due to corrosion. Accurate and computationally efficient structural modelling of corrosion deterioration is an essential prerequisite for structural reliability or fragility prediction, or life cycle cost and impact estimation. In this paper, a simplified approach for modelling reinforced concrete bridge columns that have undergone deterioration due to chloride-induced reinforcement corrosion is presented. While several models of increasing complexity are evaluated, a simplified non-linear analytical model that accounts primarily for the reduction in the steel cross-section due to corrosion is the central focus of the paper. The accuracy of the simple model is validated by comparing analytical results with experimental tests on reinforced concrete columns subjected to accelerated corrosion. The model results show excellent agreement with the experimental tests, making it particularly suitable for applications in vulnerability or reliability analysis where numerous non-linear dynamic analyses are necessary, or for further downscale or upscale integration with materials-level or system-level models.
Corrosion Mechanism and Protection Methods for Suspension Bridge Cables

Kazuhiko Furuya,Makoto Kitagawa,Shun-ichi Nakamura,Keita Suzumura

DOI: https://doi.org/10.2749/101686600780481518

2000-08-01

Structural Engineering International

Abstract:The main cables of several Japanese suspension bridges were found to be corroded. To determine the corrosion mechanism, the environments inside the cables were investigated, and corrosion simulation tests of galvanised wires were carried out. These studies showed that the corrosion environment depends on the position within the cable, with the side parts being most susceptible to corrosion. A new anti-corrosion system was developed using S-shaped wrapping wires and improved pastes to overcome this problem. Cables protected by this system were compared in long-term exposure tests with cables protected by conventional systems, and showed improved anti-corrosion performance. Another new method, namely to pass dry air through the cables, is proposed. Preliminary tests showed this system to be promising in terms of improving the anti-corrosion properties of the cables.

construction & building technology,engineering, civil
Probabilistic Assessment of the Safety of Main Cables for Long-Span Suspension Bridges considering Corrosion Effects

Hao Tian,Jiji Wang,Sugong Cao,Yuanli Chen,Luwei Li

DOI: https://doi.org/10.1155/2021/6627762

IF: 1.843

2021-03-03

Advances in Civil Engineering

Abstract:This paper presents a reliability analysis to assess the safety of corroded main cables of a long-span suspension bridge. A multiscale probability model was established for the resistance of the main cables considering the length effect and the Daniels effect. Corrosion effects were considered in the wire scale by relating the test results from accelerated corrosion tests to the corrosion stages and in the cable scale by adopting a corrosion stage distribution of the main cable section in NCHRP Report 534. The load effects of temperature, wind load, and traffic load were obtained by solving a finite element model with inputs from in-service monitoring data. The so-obtained reliability index of the main cables reduces significantly after operation for over 50 years and falls below the design target value due to corrosion effects on the mechanical properties of the steel wire. Multiple measures should be taken to delay the corrosion effects and ensure the safety of the main cables in the design service life.

construction & building technology,engineering, civil
A Stochastic Modeling Method for Three-Dimensional Corrosion Pits of Bridge Cable Wires and Its Application

Kun Fang,Zhenliang Liu,Xinyao Zhang,Xiaoqin Zha

DOI: https://doi.org/10.5006/4541

2024-06-12

CORROSION

Abstract:Cables have usually served as critical and vulnerable structural components in long-span cable-supported bridges. Cable inspections revealed that corrosion, fatigue, or coupled corrosion-fatigue were the ones of the main failure mechanisms. This paper proposed a stochastic modeling method for three-dimensional (3D) corrosion pits of high-strength bridge wires, which can be applied to rapid fatigue life evaluation according to mass loss caused by surface corrosion pits of bridge wires nondestructively. High-strength steel wire specimens dismantled from the cable-stayed bridge served for 15 y were scanned to obtain the original surface corrosion data. The spatial position coordinates of corrosion pits were considered as a random variable and can be well-fitted by uniform distribution. While the number of corrosion pits can be fitted with a generalized extreme value distribution. The uniform corrosion depth du, which can be equivalent to mass loss rate, was calculated as the input corrosion parameter for 3D corrosion pit modeling. The maximum pitting depth dmax for the steel wire was found to be associated with du. The geometric parameters for individual corrosion pits were recognized as pit depth d, depth-to-width ratio d/b, and aspect ratio b/a, which were fitted with different probability distributions. What follows is 3D spatial corrosion pits simulation based on the individual corrosion parameters that were sampled and combined from the corresponding probabilistic distributions. Hereafter, the fatigue life evaluation of corroded wires was conducted based on an equivalent surface defect method and compared with the experimental results, verifying the effectiveness of the proposed modeling approaches.

materials science, multidisciplinary,metallurgy & metallurgical engineering
THE INFLUENCES OF CORROSION DAMAGE ON THE FATIGUE CRACK DEVELOPMENT OF CONCRETE STRUCTURES

Xiaoyan Sun

2012-01-01

Abstract:Bridge members always work with damage.To study the influence of corrosion damage on the crack development of bridge members after reinforcement,a fatigue experiment is carried out to simulate the members under overloading.The results indicts that CFRP reinforcement can effectively improve the crack resistance of reinforced concrete members.However,corrosion cracks width increases quickly in serious state.It is suggested that corrosion cracks should be handled in seious state.
Probabilistic deterioration model of high-strength steel wires and its application to bridge cables

Shunlong Li,Yang Xu,Songye Zhu,Xinchun Guan,Yuequan Bao

DOI: https://doi.org/10.1080/15732479.2014.948462

2014-08-26

Structure and Infrastructure Engineering

Abstract:Bridge inspections reveal that severe corrosion and fatigue are the main failure mechanisms of bridge stay cables. This paper presents an empirical modelling of the long-term deterioration process of steel wires in cables with consideration of the simultaneous occurrence of uniform corrosion, pitting corrosion and fatigue induced by a combined action of environmental aggression and cyclic loading. Accelerated corrosion experiments are conducted to determine the different corrosion levels of high-strength steel wires, and time-dependent statistical models are developed to quantify uniform and pitting corrosion depth. Corrosion-fatigue process of steel wires is subsequently simulated using the corrosion models and cyclic stress obtained through cable force monitoring data. The mechanical properties of corroded steel wires, including yield stress, ultimate stress, ultimate strain and modulus of elasticity, are experimentally characterised, and the statistical models are established through regression analysis. Finally, the deterioration models of high-strength steel wires (including crack depth, ratio of broken wires, and remaining strength, among others) is extended to probabilistically assess the time-variant conditions of bridge cables (sectional area loss and remaining capacity). The presented study on the long-term deterioration of bridge cables would provide guidance to future decision-making regarding the maintenance and replacement of bridge cables.

engineering, mechanical, civil
Data-driven Corrosion Failure Probabilistic Assessment Model for Reinforced Concrete Structures

Ren-jie Wu,Wan-lin Min,Qing-feng Liu,Khant Swe Hein,Jin Xia

DOI: https://doi.org/10.1016/j.jobe.2024.111107

IF: 7.144

2024-01-01

Journal of Building Engineering

Abstract:The corrosion-induced failure of marine reinforced concrete structures, stemming from prolonged exposure to environments with elevated chloride content, poses a significant threat to structural integrity and serviceability. Traditional models predominantly depend on prior information to estimate the spatial stochastic degradation of aging structures, leading to a lack of comprehensiveness and accuracy in evaluation results. To address these limitations, a data-driven probabilistic assessment model for corrosion failure is proposed. This model incorporates a pre-training phase that integrates electrochemical simulations with long-term exposure data to establish the spatiotemporal distribution of corrosion failures, thereby facilitating a thorough assessment of overall damage by quantifying the corrosion failure proportion while propagating epistemic uncertainty. Subsequently, a multivariate function is derived using the non-dominated sorting genetic algorithm to elucidate the relationship between input and output variables. The efficacy of the data-driven model is evaluated through experimental observations and model predictions. The Hangzhou Bay Bridge project serves as a case study, wherein this model is demonstrated using actual data obtained from exposure experiments and field detection. Furthermore, the proposed model enables a rapid prejudgment of corrosion failure proportion, significantly reducing diagnostic time compared to conventional procedures.
Development of Corrosion-Fatigue Analysis Method of Cable Hangers in Tied-Arch Bridges Considering Train-Bridge Interaction

Y. F. Duan,S. K. Wu,H. M. Zhang,R. Zhang,C. B. Yun,J. J. R. Cheng,S. M. Wang

DOI: https://doi.org/10.1016/j.engstruct.2024.118484

IF: 5.582

2024-01-01

Engineering Structures

Abstract:This study proposes an integrated corrosion-fatigue analysis method for bridge hangers by combining the dynamic bridge-train interaction analysis for random train arrivals with various speeds and the linear elastic fracture mechanics (LEFM)-based crack propagation analysis considering the corrosion-fatigue effects. Accordingly, a three-stage process, namely, zinc coating corrosion, pit-crack transition, and corrosion-fatigue crack propagation for wires in hangers, was proposed to simulate the total service life. A train-bridge-interaction analysis was conducted on a tied-arch bridge with multiple cable hangers using the vector form intrinsic finite element method, where the stresses in the hangers were generated under high-speed train loads. The pit-crack transition was analyzed based on the pit growth and fatigue growth; whose rates compete to dominate the transition phenomenon. The fatigue crack growth rate was estimated using a LEFM approach considering the equivalent stress ranges and number of stress cycles. The effects of reducing the cable cross-section and updating the internal stress of the multi-layered wires were investigated. The present method was compared with the continuum damage mechanics model for validation. A relatively short remaining corrosion-fatigue life was found in the cables under the train loads, after corrosion of the zinc coating and pit-crack transition in the steel wires were developed.
Modeling of cable-stayed bridge and modal analysis

Serhii Krasnikov

DOI: https://doi.org/10.30977/bul.2219-5548.2022.97.0.122

2022-09-05

Bulletin of Kharkov National Automobile and Highway University

Abstract:Problem. The considered Characteristics of the own forms of a cable-stayed bridge according to several of its schemes. The analysis of the influence of the type of resistance on the characteristics of the own forms of resistance for different sets was carried out. Among the types of resistance, full rigidity, hinge and no resistance were taken. Goal. The purpose of the study is to determine the causes of registered traffic accidents and emergencies associated with them. To do this, it is proposed to analyze the own forms of the cable-stayed bridge for various types of its contact (resistance) with the columns. The object of the study is a cable-stayed bridge with a service life of about 50 years. The bridge is a system of three types of elements: pylon, span and columns. The subject of the study is the forms of natural oscillations of the bridge according to its various models. Methodology. The study was carried out by using oscillation and finite element methods. It should also be noted that the original methods for constructing models of complex machine-building systems were used, which were developed directly by the author. Results. Based on the results of the research, three-dimensional finite element models of parts and the entire bridge as a single system for various types of resistance were built, and their own forms were obtained for each model of the system. The study allows us to draw conclusions on specifying the causes of road traffic accidents and ways to prevent them. Originality. Regarding the methods of constructing models of a cable-stayed bridge, we note their uniqueness. Taking into account the features of modeling, it became possible to create several states of interaction between the parts of the system. To conduct reliable research for a real model of a structure, it is necessary to have reliable data about the real state of the connections of its elements. This state can range from absolutely rigid to free. Accounting for these features is possible with the help of a unique author's methodology for building models using the universal capabilities of the finite element method. Previous studies of the bridge by other methods did not allow us to solve the tasks set for the occurrence of traffic accidents. Practical value. The results of the work have direct practical application. Based on the results of the work, conclusions were drawn about ways to improve the reliability of the system and the measures to prevent traffic accidents.
A data-driven model for damage evolution of bridge stay cable

Guowen Yao,Qianling Wang,Fengmin Chen,Li Ying,Xuanbo He,Shengbao Zhen,Xuanrui Yu

DOI: https://doi.org/10.1016/j.cscm.2024.e03209

IF: 4.934

2024-05-02

Case Studies in Construction Materials

Abstract:Chloride ion concentration is crucial for the reliability of stay cables, particularly when their protective covers are compromised. Previous studies have focused on the corrosion of single wires or cables over time, proposing estimation models that primarily consider corrosion duration while neglecting other significant factors. Addressing this gap, this paper establishes a corrosion damage model for stay cables considering time, temperature, humidity and inclination angle based on the diffusion characteristics of chloride ions. Firstly, We conducted accelerated corrosion experiments on stay cables in different environments to assess the characteristics of the spatial distribution of chloride ion concentrations within the cables and the mass loss characteristics of the wires. Secondly, a three-dimensional diffusion model for chloride ions in stay cables is proposed based on Fick's second law. A pivotal innovation of our research is the application of diverse machine learning techniques to explore how the diffusion coefficient of chloride ions is influenced by factors like time and environmental temperature, leading to the formulation of a sophisticated chloride ion diffusion model. Finally, by amalgamating this diffusion model with the established corrosion law for steel reinforcement, we devised a comprehensive corrosion damage evolution model for the steel wires of stay cables. The result demonstrates the anisotropic diffusion of chloride ions and its substantial correlation with the corrosion damage observed in steel wires. Notably, the PSO-BPNN method emerged as a highly accurate predictor for the diffusion coefficient of chloride ions. The model established in this paper considers a variety of influencing factors and accurately predicts the corrosion damage characteristics of stay cables, which makes an important contribution to improving the reliability of stay cables.

materials science, multidisciplinary,engineering, civil,construction & building technology
Effect of fatigue load on the bending tribo-corrosion-fatigue behaviors between the main cable wires

Bo Wang,Dagang Wang,Jihong Ye,Liang Tang,Hailang Chong,Wei Xu,Xinxin Zhang,Jianhao Chen,Haiyan Deng,Jie Zhang,Guowen Yao,Magd Abdel Wahab

DOI: https://doi.org/10.1007/s40544-023-0830-y

IF: 4.924

2024-04-03

Friction

Abstract:Abstract The main cable bent around the saddle of the suspension bridge is subjected to the wind, the vehicle, the bridge’s own weight and the corrosive media. The coupling of the three loads and the environments causes the friction, the corrosion, and the fatigue (tribo-corrosion-fatigue) among the wires inside the main cable. In this paper, a wire bending tribo-corrosion-fatigue test rig was designed and developed. The effect of fatigue load on the bending friction behaviors between the cable wires in ultrapure water and 3.5% NaCl solution was explored. The tribological properties and electrochemical corrosion behaviors under different fatigue loading ranges were investigated. The tribo-corrosion-fatigue interaction between the cable wires was quantitatively characterized, and the mechanism of the interaction was analyzed. The results demonstrate that the increasing fatigue load exacerbates the coupling damage of the cable wires attributed to the enhanced interaction. The findings carry theoretical importance when assessing the main cable’s deterioration and the load-bearing safety of a suspension bridge.

engineering, mechanical
Prevention of main cable corrosion by dehumidification

Matthew L. Bloomstine,Ove Sørensen

DOI: https://doi.org/10.1201/9781315106618-16

2017-12-14

Abstract:Corrosion of main cables on suspension bridges is a major problem on a worldwide basis. The load carrying wires are covered by wrapping wire and corrosion is therefore hidden and often progresses to a very serious level before it is detected. Many examples have illustrated that traditional corrosion protection systems for main cables do not prevent corrosion, but merely slows it down. This has led to the development and application of dehumidification of main cables, which truly prevents corrosion. A dehumidification system blows dry air through the main cables and keeps the atmosphere in the cables so dry that corrosion can not occur. This paper describes the details of such a system, design considerations, results of Life Cycle Cost Analysis and experience from systems in operation. Corrosion of main cables on suspension bridges is a major problem on a worldwide basis. The load carrying wires are covered by wrapping wire and corrosion is therefore hidden and often progresses to a very serious level before it is detected. This chapter describes the details of such a system, design considerations, results of Life Cycle Cost Analysis and experience from systems in operation. The chapter presents a description of the dehumidification concept, a description of systems for main cables, considerations for designing a system, results of Life Cycle Cost Analysis demonstrating that dehumidification is much more economical than a traditional system and Case stories/experience from systems in service. Many of the main components of major bridges are steel structures. In order to ensure a long service life and provide an appropriate level of safety, these structures must be protected from corrosion.
Corrosion fatigue analysis of suspenders on continuous suspension bridge under combined action of wind and traffic

Zhijie Yuan,Hao Wang,Rou Li,Lingxiao Wang,Jianxiao Mao,Hai Zong

DOI: https://doi.org/10.1016/j.engfailanal.2024.109037

IF: 4

2024-11-04

Engineering Failure Analysis

Abstract:Suspenders and displacement-controlled device (DCD) are crucial force transmission components connecting the girder and the main cable in the continuous suspension bridge. These two structures will be subjected to environmental corrosion and fatigue loading simultaneously after the protection system fails. To investigate the safety of structure during the service, a comprehensive framework for corrosion fatigue analysis of continuous suspension bridge under the combined effects of wind and traffic flow was proposed. Taking a three-span continuous suspension bridge with DCD as engineering background, the wind-traffic combined load model was established and the fatigue life of the corroded suspenders was examined. Based on the Multilayer Perceptron algorithm, the impact of load form, environmental grade and DCD type on the corrosion fatigue performance of suspenders was analyzed. The results indicate that the fatigue life of suspender is significantly reduced due to uniform and pitting corrosion of the internal steel wires. The early failure mechanism of suspender is extremely sensitive to corrosion factors. Traffic load is the primary cause of fatigue damage to suspenders. Setting up DCD is beneficial for improving the corrosion fatigue life of the suspenders, and the selection of DCD type mainly depends on the topographical factors of the bridge site.

engineering, mechanical,materials science, characterization & testing
Numerical Simulation of Airflow in the Main Cable of Suspension Bridge with FPM Model

Wenhao Sui,Zhihang Guo,Hua Guan,Pei Peng,Qun Liu,Xiaochen Zhang,Xiangdong Cheng

DOI: https://doi.org/10.3390/buildings13061422

IF: 3.324

2023-05-31

Buildings

Abstract:The main cable of suspension bridges is subject to corrosion and requires advanced anti-corrosion technology. Consequently, the internal airflow of the main cable has become a significant research focus. This study employs image processing and machine learning to analyze the cross-sectional images of the main cable and reveals the distribution characteristics of pores and fractures within the main cable cross-section. The numerical simulation model of the main cable is divided into inner and outer parts based on porosity, with porosity levels of 18.16% and 32.11%, respectively. Fractures randomly occurred in the inner part, with a probability of 31.37%. A simulation model based on fractured porous media (FPM) is developed, which innovatively incorporates the fracture flow model into the numerical simulation of the internal airflow of the main cable. The numerical simulation clearly explores the intricate details of the internal flow field of the main cable, revealing that the existence of fractures has a great impact on the internal flow field of the main cable. Additionally, the relative deviation of specific frictional head loss between the field experiment and numerical simulation is about 6.83%, indicating that the numerical simulation results are relatively reliable.

construction & building technology,engineering, civil
In-service performance assessment of fire-corrosion damaged cables of bridges

Jinpeng Feng,Jinglun Li,Kang Gao,Yi Li,Tao Li,Gang Wu,Weigang Zhao

DOI: https://doi.org/10.1016/j.engstruct.2023.117221

IF: 5.582

2023-12-02

Engineering Structures

Abstract:Cable-supported bridges are prone to fire hazards , and the corrosion within further compromises their structural integrity. The present study provides a novel framework for assessing fire-corrosion damage of steel wires currently in use. The relations and failure modes of steel wires under coupled effects of fire-corrosion are established by conducting the tensile test utilizing the replaced steel wires after the fire. Experimental studies found that the deterioration tendency of in-service steel wires after the fire is consistent with that of intact ones, while the corrosion level and position of steel wire have a significant impact on its ultimate strain. To predict the residual mechanical properties of cables after the fire-corrosion coupled damage, a comprehensive database of steel wires properties after the fire is established, and then a data-driven surrogate model is proposed. Finally, four grades are suggested to evaluate various damage degrees of in-service cables under corrosion and fire. The findings can provide bridge owners with guidance on how to replace or repair the damaged components after accidents or natural disaster, thereby increasing the reliability and lifespan of bridges and decreasing the costs associated with maintenance, reconstruction, and replacement.

engineering, civil

Modeling Corrosion in Suspension Bridge Main Cables

Corrosion-Fatigue Analysis of Wires in Bridge Cables Considering Time-Dependent Electrochemical Corrosion Process

Estimation model for steel wire crack propagation and its application in calculation of pre-corrosion fatigue life

Probability-Based Performance Degradation Model and Constitutive Model for the Buckling Behavior of Corroded Steel Bars

Experimental Study and Residual Performance Evaluation of Corroded High-Tensile Steel Wires

Effect Of Corroded Surface Morphology On Ultra-Low Cycle Fatigue Of Steel Bridge Piers

Simplified Structural Deterioration Model for Reinforced Concrete Bridge Piers under Cyclic Loading 1

Corrosion Mechanism and Protection Methods for Suspension Bridge Cables

Probabilistic Assessment of the Safety of Main Cables for Long-Span Suspension Bridges considering Corrosion Effects

A Stochastic Modeling Method for Three-Dimensional Corrosion Pits of Bridge Cable Wires and Its Application

THE INFLUENCES OF CORROSION DAMAGE ON THE FATIGUE CRACK DEVELOPMENT OF CONCRETE STRUCTURES

Probabilistic deterioration model of high-strength steel wires and its application to bridge cables

Data-driven Corrosion Failure Probabilistic Assessment Model for Reinforced Concrete Structures

Development of Corrosion-Fatigue Analysis Method of Cable Hangers in Tied-Arch Bridges Considering Train-Bridge Interaction

Modeling of cable-stayed bridge and modal analysis

A data-driven model for damage evolution of bridge stay cable

Effect of fatigue load on the bending tribo-corrosion-fatigue behaviors between the main cable wires

Prevention of main cable corrosion by dehumidification

Corrosion fatigue analysis of suspenders on continuous suspension bridge under combined action of wind and traffic

Numerical Simulation of Airflow in the Main Cable of Suspension Bridge with FPM Model

In-service performance assessment of fire-corrosion damaged cables of bridges