Abstract:Inorganic CsPbIBr2 perovskite has been considered as a promising light-absorbing material for solar cells due to its high stability and suitable bandgap. Although the remarkable improvement of CsPbIBr2 PSC has been achieved, the efficiency of this cell is still lower than those of other analogues and far below its theoretical limit. This is mainly due to the serious charge recombination in the as-fabricated CsPbIBr2 cells derived from the poor-quality CsPbIBr2 perovskite film with a large quantity of defects and numerous grain boundaries. Therefore, fabricating high-quality CsPbIBr2 perovskite film is a key factor for the further efficiency improvement of CsPbIBr2 PSCs. Herein, phenylthiourea (PTU) additive is introduced into the CsPbIBr2 precursor to tailor the crystallization of CsPbIBr2 perovskite for fabricating high-quality CsPbIBr2 perovskite. The C=S group of PTU can coordinate with PbBr2 in the precursor owing to the lone-pair electrons on S and the empty orbits of Pb2+. The strong interaction between PTU and the CsPbIBr2 precursor components can form PTU·Pb···Br(I) intermediate phase in the precursor upon PTU introduction. The PTU·Pb···Br(I) intermediate phase can reduce the nucleation rate of perovskite and modulate the perovskite crystal growth because the extra energy is required to break the strong coordination bond in the intermediate phase, resulting in a low crystallization rate of CsPbIBr2 perovskite. Such a retardation of perovskite crystallization is conducive to the formation of high-crystallinity perovskite film with smooth surface, large crystal grains, high crystallization, and low density of defect. Meanwhile, the decomposition of PTU during thermal annealing makes the S2– inserted into interstitial of CsPbIBr2 crystal lattice, which greatly enhance the stability of CsPbIBr2 perovskite. The carbon-based PSCs with a normal n-i-p structure of FTO/compact-TiO2 layer/meso-TiO2 layer/perovskite film/carbon layer are fabricated, and their photovoltaic performances are measured under a simulated AM1.5 illumination (100 mW·cm–2). The PSC based on PTU-CsPbIBr2 perovskite delivers a high power conversion efficiency of 10.09%, which is much higher than that of the control device. This great improvement of photovoltaic performance can be attributed to the largely promoted perovskite quality, which enhances the charge collection and suppresses the charge recombination in the device. In addition, the unencapsulated device preserves 82% of the initial efficiency after being stored under ambient condition for 35 days, suggesting excellent stability. Therefore, this work provides an effective complementary strategy for effectively improving the performance of inorganic PSCs.

3‐Hydrazinylpyridine Hydrochloride Regulating Crystallization Kinetics of Tin‐Lead Perovskite Prepared by Two‐Step Method

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

Managing Crystallization and Phase Distribution Via 2D Perovskite Seed Crystals for 2D-3D Tin-based Perovskite Solar Cells

Bifunctional additive 2-amino-3-hydroxypyridine for stable and high-efficiency tin–lead perovskite solar cells

Importance of tin (II) acetate additives in sequential deposited fabrication of Sn-Pb-based perovskite solar cells

Synergistic Modulation of Sn2+ Oxidation and Perovskite Crystallization Induced by 4-Hydroxypyridine for Stable Lead-Free Solar Cells

The Molecular Additive N-Acetyl-L-Phenylalanine Delays the Crystallization and Suppresses the Phase Impurity for Achieving Triple-Cation Perovskite Solar Cells with Efficiency over 25.

Synergic Solventing-out Crystallization with Subsequent Time-Delay Thermal Annealing of PbI2 Precursor in Mesostructured Perovskite Solar Cells

Regulation of Lead Iodide Crystallization and Distribution for Efficient Perovskite Solar Cells

Crystallization Kinetics Modulation of FASnI3 Films with Pre‐nucleation Clusters for Efficient Lead‐Free Perovskite Solar Cells

Efficient and Stable Tin‐Lead Mixed Perovskite Solar Cells Using Post‐Treatment Additive with Synergistic Effects

Hydroxyl‐Rich d ‐Sorbitol to Address Transport Layer/Perovskite Interfacial Issues toward Highly Efficient and Stable 2D/3D Tin‐Based Perovskite Solar Cells

Preferentially Coordinating Tin Ions to Suppress Composition Segregation for High-performance Tin-lead Mixed Perovskite Solar Cells

Reactive Inhibition Strategy for Triple‐cation Mixed‐halide Perovskite Ink with Prolonged Shelf‐life

Tailoring of CsPbIBr2 Perovskite Crystallization Via Phenylthiourea for Stable and Efficiency Perovskite Solar Cells

Precrystallized‐Heterojunction Strategy on Precursor Solution Enables High‐Performance Semitransparent Perovskite Solar Cells

Colloidal Zeta Potential Modulation as a Handle to Control the Crystallization Kinetics of Tin Halide Perovskites for Photovoltaic Applications

Multifunctional anion-cation modulation engineering for Sn-Pb perovskite solar cells

Improving Crystallization and Stability of Perovskite Solar Cells Using a Low-Temperature Treated A-Site Cation Solution in the Sequential Deposition

Modulation of Nucleation and Crystallization in PbI2 Films Promoting Preferential Perovskite Orientation Growth for Efficient Solar Cells

Multidentate Coordination Induced Crystal Growth Regulation and Trap Passivation Enables over 24% Efficiency in Perovskite Solar Cells