Abstract:To reduce carbon emissions associated with substantial concrete usage in construction and achieve the objectives of green and low-carbon construction, this study innovatively develops a low-carbon binary material by adding limestone powder (LP) and silica fume (SF) into the conventional cement-based material, enhancing the comprehensive utility value of LP. The experimental results show that the addition of 15% LP and 5% SF increases the yield stress of the mortar yet substantially reduces the plastic viscosity to 2.84 Nmm·min, representing a 44.5% decrease compared to pure cement slurry. This reduction is conducive to long-distance pumping of the cement-based material. Moreover, the addition of 5% SF compensates for the 18.8% (mid-stage, 28-d) and 15.8% (late-stage, 90-d) strength loss in mortar caused by LP while simultaneously improving the strength of the co-mixed system by 10.4% (mid-stage) and 10.8% (late-stage). In the early-stage measurements of the LP-SF binary cement-based materials, it is observed that while SF slightly increases the hydration heat release, LP suppresses the early hydration heat release. Therefore, the total heat release observed in the 15% LP and 5% SF group after 72 h is only 254 J/g, demonstrating favorable temperature control and crack prevention effects. In addition, X-ray diffraction (XRD) and thermogravimetric/differential thermogravimetric (TG/DTG) phase analysis reveal a notable increase of 53.56% in CH consumption. Besides, the weight loss on ignition of C-S-H crystals increases, indicating that the secondary hydration of LP and the pozzolanic reaction of SF promote the production of C-S-H in the system. Combined with the late-stage strength and water absorption characteristics, it is concluded that the system exhibits good mechanical properties and compactness. This study presents a use of mixed proportion that enables excellent mechanical properties, good pumping performance, and low hydration heat. Moreover, the analysis indicates that the carbon emission of each cubic meter of the as-developed mortar is reduced by approximately 16.7–23.9%, promoting the efficient and clean utilization of LP and SF.

Seawater Mixed with One Part Alkali Activated Material: An Environmental and Cost Evaluation

Sustainable Building Material from CO2 Mineralization Slag: Aggregate for Concretes and Effect of CO2 Curing

Recent Advances in Alkali-Activated Materials with Seawater and Sea Sand

Early crack resistance and life cycle assessment of seawater-mixed sintered sludge cement paste

Effects of w/b ratio, fly ash, limestone calcined clay, seawater and sea-sand on workability, mechanical properties, drying shrinkage behavior and micro-structural characteristics of concrete

Effect of Seawater on Hydration and Sulfate Resistance of Noncement Mortars

Mechanical properties and hydration of ultra-high-performance seawater sea-sand concrete (UHPSSC) with limestone calcined clay cement (LC3)

Investigating the effects of seawater and sea sand aggregates and supplementary cementitious materials on the early shrinkage and crack resistance of concrete

Development of eco-friendly binder using metakaolin-fly ash–lime-anhydrous gypsum

Development of sustainable concrete incorporating seawater: A critical review on cement hydration, microstructure and mechanical strength

Microstructures and properties of alkali-activated slags with composite activator: Effects of Na2O equivalents

Alkali-Activated Binders as Sustainable Alternatives to Portland Cement and Their Resistance to Saline Water

Clinker-Free Cement Based on Calcined Clay, Slag, Portlandite, Anhydrite, and C-S-H Seeding: An SCM-Based Low-Carbon Cementitious Binder Approach

Waste-Based One-Part Alkali Activated Materials

Reuse of the soda sludge dealt with water washing as a supplementary material for the synthesis of clinker binders

Hydration of Portland cement with seawater toward concrete sustainability: Phase evolution and thermodynamic modelling

Examining the early-stage performance and mechanical performance of limestone powder-silica fume binary cement-based materials

Investigating embodied carbon, mechanical properties, and durability of high-performance concrete using ternary and quaternary blends of metakaolin, nano-silica, and fly ash

Effect of organic alkali on hydration of GGBS-FA blended cementitious material activated by sodium carbonate

Performance and life cycle of Portland limestone cement mixes admixed with gypsum

Alkali-Activated Slag as Sustainable Binder for Pervious Concrete and Structural Plaster: A Feasibility Study