Abstract:The practical application of lithium-sulfur (Li-S) batteries is limited by the easy dissolution of polysulfides in the electrolyte, resulting in the lithium polysulfide (LPS) shuttle effect. Several two-dimensional (2D) materials with abundant active binding sites and high surface-to-volume ratios have been developed to prepare functional separators that suppress the diffusion of polysulfides. However, the influence of modified layer thickness on Li+ transport has not been considered. Herein, we synthesized individual and multilayered 2D Ti3C2Tx MXene nanosheets and used them to fabricate a series of Ti3C2Tx-PP modified separators. The separators had mass loadings ranging from 0.16 to 0.016 mg cm(-2), which is the lowest value reported for 2D materials to the best of our knowledge. The corresponding reductions in thickness ranged from 1.2 mu m to 100 nm. LPS shuttling was effectively suppressed, even at the lowest mass loading of 0.016 mg cm(-2). Suppression was due to the strong interaction between LPS intermediates and Ti atoms and hydroxyl functional groups on the separator surface. The lithium-ion diffusion coefficient increased with the reduction of Ti3C2Tx layers on the separator. Superior cycling stability and rate performance were attained when the separator with a Ti3C2Tx-PP mass loading of 0.016 mg cm(-2) was incorporated into a Li-S battery. Carbon nanotubes (CNTs) were introduced into the separators to further improve the electrical and Li+ ionic conductivity in the cross-plane direction of the 2D Ti3C2Tx layers. With the ultra-lightweight Ti3C2Tx/CNTs modified PP separator, the cell maintained a capacity of 640 mAh g(-1) after 200 cycles at 1 C with a capacity decay of only 0.079% per cycle. (C) 2019 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights reserved.

A 2D montmorillonite-carbon nanotube interconnected porous network that prevents polysulfide shuttling

Two-dimensional Molybdenum Nitride Nanosheets Modified Celgard Separator with Multifunction for LiS Batteries

Suppression Of Polysulfide Shuttling With A Separator Modified Using Spontaneously Polarized Bismuth Ferrite For High Performance Lithium-Sulfur Batteries

Porous Ionic Network/CNT Composite Separator as a Polysulfide Snaring Shield for High Performance Lithium‐Sulfur Battery

Multifunctional Lithium Phytate/Carbon Nanotube Double-Layer-Modified Separators for High-Performance Lithium-Sulfur Batteries

Carbon-coated Nitrogen, Vanadium Co-Doped MXene Interlayer for Enhanced Polysulfide Shuttling Inhibition in Lithium-Sulfur Batteries

Tg-C 3 N 4 -coated functional separator as polysulfide barrier of high-performance lithium-sulfur batteries

Carbon-Based Porous Bimetallic Phosphide in CNT Network As a Separator for Li–S Batteries

TiO2@Porous carbon nanotubes modified separator as polysulfide barrier for lithium-sulfur batteries

Nitrogen‐Deficient Graphitic Carbon Nitride/Carbon Nanotube as Polysulfide Barrier of High‐Performance Lithium‐Sulfur Batteries

Designing a Functional CNT+PB@MXene-Coated Separator for High-Capacity and Long-Life Lithium-Sulfur Batteries

An Interlayer Composed of a Porous Carbon Sheet Embedded with TiO2 Nanoparticles for Stable and High Rate Lithium-Sulfur Batteries.

Inhibiting polysulfide shuttling with a flexible "skin" for highly stable Lithium-Sulfur batteries

Three-dimensional P-doped carbon skeleton with built-in Ni2P nanospheres as efficient polysulfides barrier for high-performance lithium-sulfur batteries

Enhancing Lithium-Sulfur Battery Performance through Electronic/Ionic Co-Conductive MWCNTs/LLTO Separator Modification

Efficient polysulfides trapping and redox enabled by Co/N-carbon implanted Li+-montmorillonite for advanced lithium-sulfur batteries

Ultra-lightweight Ti3C2T MXene Modified Separator for Li–S Batteries: Thickness Regulation Enabled Polysulfide Inhibition and Lithium Ion Transportation

CoS 2 -MoS 2 -CNT composite modified separator with enhanced LiPS adsorption capacity for lithium-sulfur battery

Empowering polypropylene separator with enhanced polysulfide adsorption and reutilization ability for high-performance Li-S batteries

Multifunctional Interlayer Based on Molybdenum Diphosphide Catalyst and Carbon Nanotube Film for Lithium-Sulfur Batteries.

Modified separators boost polysulfides adsorption-catalysis in lithium-sulfur batteries from Ni@Co hetero-nanocrystals into CNT-porous carbon dual frameworks