Abstract:Abstract The field under study is located in the northern part of Oman where most of the fields have a tight carbonate oil reservoirs. Initially the field was produced under natural depletion for almost 15 years until 2005 when a line drive water flood development with horizontal wells took place and was deployed in the whole field. After more than 10 years of water injection, the water cut reached an average of 75% in the major producing blocks. The reservoir has a light oil with viscosity of 0.8 mPa.s, a downhole temperature of 87°C and average permeability of 10 mD. The calcium and magnesium concentration in formation water is high, about 4000 mg/L. Reservoir heterogeneity in tight carbonate reservoirs causes uneven water flood sweep efficiency and hence resulted in a lot of bypassed oil. The initial EOR methods screening in the field under study didn't recommend to use the conventional polymer flooding due to low reservoir permeability and hence injectivity challenge. However, a new unique nano-ploymer was recently developed in the market to be a potential EOR method for such tight formation reservoirs. Extensive laboratory experiments using the core and fluid samples from the studied reservoir followed by numerical simulation modeling work proved the technical feasibility for this new polymer. This was then followed by field testing pilot in one of the matured water flood sector and the performance is currently under monitoring. The new polymer is a particle-type and comes with various nanometer-micrometer sizes. This polymer has a low apparent viscosity of 1-4 mPa and when it is mixed with the injection water, the particles disperse in the water and the resultant mixture has a low viscosity making it easily to be injected. In addition, this nano-polymer has a high tolerance for both temperature and salinity. While the particles move into formation, they temporarily plug the preferential existing water paths and divert the injection water into the relatively small pores/throats and displace the remaining bypassed oil. The polymer particle has high deformation capacity, so it can deform and pass through the throat under certain pressure to plug even deeper parts of the formation. The process is repeated continuously so that it can inhibit water production and enhance oil production. For the lab experiments, 12 core plugs from the associated reservoir were collected, based on which, a series of experiments were conducted including: core thin section analysis, injectivity test for the nano-polymer and core flooding experiments on single plug and parallel double plugs. Subsequently, the lab results were utilized for numerical simulation and that was followed by economic evaluation. Based on the lab test results, a conceptual simulation model for the studiedfield's sector was used to estimate the incremental oil gain at different pore volume (PV) injection. The incremental oil gain was determined at different SMG PV injection starting from 0.05PV to 0.5 PV. The results showed that the best economic scenario is to go for PV injection of 0.3 which can be achieved in ~4 years'time. However, in order to expedite the field trail stage and reduce its cost, the lowest PV injection was selected which involves injection in two water injectors for one year only at 0.05 PV. The field pilot thus far has successfully completed the injection phase of the total planned volume (0.05 PV) of nano-ploymer. The injection was continuous for one year with no injectivity issue and the production performance is currently under monitoring.

Understanding Plugging Agent Emplacement Depth with Polymer Shear Thinning: Insights from Experiments and Numerical Modeling

Production Optimization under Injection of Biopolymer, Synthetic Polymer and Gels in a Heterogeneous Reservoir

A new method for plugging the dominant seepage channel after polymer flooding and its mechanism: Fracturing–seepage–plugging

Development and Application of Polymer Plugging Remover for Polymer Injection Well in Changqing Oilfield

Core- and pore-scale investigation on the migration and plugging of polymer microspheres in a heterogeneous porous media

Mechanistic Study on the Decrease in Injectivity during Salt-Resistant Polymer Flooding

Development and performance evaluation of hydrophobic association plugging agents for sealing formation prior to cementing

Pore-Scale Investigation on the Plugging Behavior of Submicron-Sized Microspheres for Heterogeneous Porous Media with Higher Permeability

Experimental Study of Synergy between Polymeric Microspheres and Nanoemulsions for Profile Control and Water Plugging

The Research of Polymer Film-Forming Plugging Agent for Drilling Fluid

Experimental Research on the Optimization and Evaluation of the Polymer/Chromium-Ion Deep Profile Control System for the Fractured Low-Permeability Reservoirs

Experimental Investigation of Polymer Injection in High Permeability Conduits for Material Sustainability and Behavior in Oil Reservoirs

Migration characteristics and plugging rules of self-aggregating nanoparticles in the porous media

A Submicron-Scale Plugging Agent for Oil-Based Drilling Fluid Synthesized Using the Inverse Emulsion Polymerization Method

Water Shutoff and Conformance Improvement for Lamadian Oilfield in Daqing Using a Novel Polymer System: Experimental Study, Simulation, and Pilot Tests

A New Polymer Flooding Technology for Improving Low Permeability Carbonate Reservoir Recovery--From Lab Study to Pilot Test--Case Study from Oman

Study on the Profile Control and Oil Displacement Mechanism of a Polymer Nano-microsphere for Oilfield

Polymer Injectivity: Investigation of Mechanical Degradation of EOR Polymers Using In-Situ Rheology

Micro-nano polymer microspheres as a plugging agent in oil-based drilling fluid

Simulation of Polymer Injection in Granular Media: Implications of Fluid-Driven Fractures, Water Quality, and Undissolved Polymers on Polymer Injectivity

Displacement Mechanism and Flow Characteristics of Polymer Particle Dispersion System Based on Capillary Bundle Model