Fibrinolysis and coagulation abnormalities in systemic lupus erythematosus

A. Doria,A. Ghirardello,M. Boscaro,M. Viero,E. Vaccaro,G. Patrassi,P. Gambari

DOI: https://doi.org/10.1007/BF00262299

Rheumatology International

Abstract:

What problem does this paper attempt to address?

Glass Transition in Gels

Rui Xiao,Hai Li

DOI: https://doi.org/10.1103/physrevmaterials.5.065604

IF: 3.98

2021-01-01

Physical Review Materials

Abstract:Recent works have shown that gels with a large amount of solvents can still exhibit a glass transition behavior with the thermomechanical properties exhibiting tremendous change over a narrow temperature region. Similar to dry polymers, the rheological behaviors of gels also show a broad distribution of relaxation times. However, so far the effects of solvents on the relaxation spectrum have rarely been studied. In this work, we first develop a viscoelastic model to relate the rheological properties of gels and the corresponding properties in the dry state. We then apply the theoretical model to analyze the complex modulus of gels measured in the small strain dynamic tests. The results show that the breadth of relaxation spectrum has been expanded by increasing the swelling ratio. The physical mechanism behind this observation needs a deep investigation in further study and also raises a significant challenge for developing constitutive models for gels.
Competition among physical, chemical, and hybrid gelation mechanisms in biopolymers

Ricky Frank López-Santiago,Jorge Delgado,Rolando Castillo

DOI: https://doi.org/10.1039/d3sm01682j

IF: 4.046

2024-02-15

Soft Matter

Abstract:Depending on how they form their linkings, biopolymer gelatin gels are commonly classified as physical, chemical, or hybrid; in gelatin hybrid gels, the physical and chemical crosslinking mechanisms run simultaneously. Gels' viscoelastic behavior following different gelation processes was determined around the gel point. Their gel fractal dimensions were obtained using the BST-scaling model from large amplitude oscillatory shear results. Hybrid gels' fractal dimension is between 1.46 and 1.60, where the value depends on the dominant crosslinking process. The main features of the Lissajous-Bowditch curves were determined for maturated gels that follow different gelation processes, and it is possible to observe the dominant gelation mechanism. The gelation kinetics process is followed by measuring the mean squared displacement (MSD) of microspheres embedded in gelatin solutions using diffusion wave spectroscopy, which in turn allows evaluating G'(ω) and G"(ω), the persistence length, and the mesh size as a function of time along the gelation process. The MSD, as a function of the elapsed time from the starting gelation process, follows a behavior that depends on the gelation processes. As time elapses after gelation starts, the persistence length of the unstructured, non-bonded flexible polymer sections decreases due to the formation of bonds. In the hybrid case, it is not a mixture of both processes; they are not independent when running simultaneously. The time evolution of the gel network's mesh size roughly follows an exponential decay.

polymer science,chemistry, physical,materials science, multidisciplinary,physics
Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Dongdong Li,Baoqing Shentu,Zhixue Weng

DOI: https://doi.org/10.1080/00222348.2011.557617

2011-01-01

Abstract:Polylactide (PLA)/poly(ethylene-co-octene) (POE) blends containing ethylene-glycidyl methacrylate copolymer (EGMA) as a compatibilizer were prepared by melt blending. An immiscible, two-phase structure with POE dispersed in the PLA matrix was observed by scanning electron microscopy. It was found that the POE particle size was significantly decreased by the addition of EGMA, and the POE particle size and distribution decreased with the increase of the compatibilizer content up to 2% EGMA, beyond which the POE particle size and distribution remained unchanged. The reactions between the epoxy groups of EGMA and carboxylic or hydroxyl groups of PLA were elucidated by the Fourier transform infrared spectroscopy. Rheological results showed that the G'(omega), G "(omega), and complex viscosity of PLA/POE blends significantly increased at low frequencies with the addition of EGMA. The failure mode changed from brittle fracture of the neat PLA to ductile fracture of the PLA/POE blends.
Effect of Polymer Gel Elasticity on Complex Coacervate Phase Behavior

Kathryn G Wilcox,Kai R Yamagami,Brittany K Roopnarine,Adam Linscott,Svetlana Morozova

DOI: https://doi.org/10.1021/acspolymersau.3c00027

2023-12-26

Abstract:Gels are key materials in biological systems such as tissues and may control biocondensate formation and structure. To further understand the effects of elastic environments on biomacromolecular assembly, we have investigated the phase behavior and radii of complex coacervate droplets in polyacrylamide (PAM) networks as a function of gel modulus. Poly-l-lysine (PLL) and sodium hyaluronate (HA) complex coacervate phases were prepared in PAM gels with moduli varying from 0.035 to 15.0 kPa. The size of the complex coacervate droplets is reported from bright-field microscopy and confocal fluorescence microscopy. Overall, the complex coacervate droplet volume decreases inversely with the modulus. Fluorescence microscopy is also used to determine the phase behavior and concentration of fluorescently tagged HA in the complex coacervate phases as a function of ionic strength (100-270 mM). We find that the critical ionic strength and complex coacervate stability are nonmonotonic as a function of the network modulus and that the local gel concentration can be used to control phase behavior and complex coacervate droplet size scale. By understanding how elastic environments influence simple electrostatic assembly, we can further understand how biomacromolecules exist in complex, crowded, and elastic cellular environments.
Oscillatory rheometry for elucidating the influence of non-network biopolymer aggregation on pectin-gelatin composite gels

Jiaxin Song,Sen Hu,Zhenjun Liu,Yimin Wang,Lin Lei,Guohua Zhao,Yun Zhou

DOI: https://doi.org/10.1016/j.ijbiomac.2023.128543

IF: 8.2

2023-12-10

International Journal of Biological Macromolecules

Abstract:Gel networks formed from biopolymers have intrigued rheological interest, especially in the food industry. Despite ubiquitous non-network biopolymer aggregation in real gel food systems, its fundamental rheological implications remain less understood. This study addresses this by preparing pectin-gelatin composite gels with dispersed or aggregated biopolymers and comparatively analyzing viscoelastic responses using rheometry. Subtle discrepancies in non-network biopolymer states were revealed through oscillatory shearing at different frequencies and amplitudes. Biopolymer aggregation in the network notably influenced loss tangent frequency dependency, particularly at high frequencies, elevating I 3 / I 1 values and sensitizing the yield point. Non-network biopolymers weakened Payne effects and gel non-linearity. A combination of strain stiffening and shear thinning nonlinear responses characterized prepared gel systems. Aggregation of pectin and gelatin enhanced shear thinning, while strain stiffening was notable in highly aggregated pectin cases. This study enhances understanding of the link between non-network structural complexity and viscoelastic properties in oscillatory rheometry of food gels.

polymer science,biochemistry & molecular biology,chemistry, applied
Link between morphology, structure and interactions of composite microgels

Rodrigo Rivas-Barbosa,José Ruiz-Franco,Mayra A. Lara-Peña,Jacopo Cardellini,Angel Licea-Claverie,Fabrizio Camerin,Emanuela Zaccarelli,Marco Laurati

DOI: https://doi.org/10.1021/acs.macromol.1c02171

2021-11-07

Abstract:We combine small angle scattering experiments and simulations to investigate the internal structure and interactions of composite Poly(N-isopropylacrylamide)-Poly(ethylene glycol) (PNIPAM-PEG) microgels. At low temperatures the experimentally determined form factors and the simulated density profiles indicate a loose internal particle structure with an extended corona, that can be modeled as a star-like object. Increasing temperature across the volumetric phase transition, the form factor develops an inflection which, using simulations, is interpreted as arising from a configuration in which PEG chains are incorporated in the interior of the PNIPAM network. In this configuration a peculiar density profile characterized by two dense, separate regions is observed, at odds with configurations in which the PEG chains reside on the surface of the PNIPAM core. The conformation of the PEG chains have also profound effects on the interparticle interactions: While chains on the surface reduce the solvophobic attractions typically experienced by PNIPAM particles at high temperatures, PEG chains inside the PNIPAM network shift the onset of attractive interaction at even lower temperatures. Our results show that by tuning the morphology of the composite microgels we can qualitatively change both their structure and their mutual interactions, opening the way to explore new collective behaviors of these objects.

Soft Condensed Matter
Effect of hydrocolloid and minerals content on the mechanical properties of gels

A. Nussinovitch,I.J. Kopelman,S. Mizrahi

DOI: https://doi.org/10.1016/s0268-005x(09)80202-6

IF: 10.7

1990-12-01

Food Hydrocolloids

Abstract:The mechanical behavior of agar, carrageenan and alginate gels was evaluated for a wide range of gum and setting agent concentrations as well as for different gel preparation methods. Two types of gel were defined based on their mode of mechanical response to a change in the concentration of the gel-forming components. The first type, which includes alginate set with glucono-D-lactone and carrageenan gels, is characterized by a maximum in the value of yield stress and of the deformability modulus at a certain gum and setting agent concentration. This phenomenon is attributed to the trend of formation of aggregates, at high reactants (gum and setting agent) concentration, rather than a strong gel having a uniform matrix of high density of cross-linkage bonds. Although on both sides of the maximum point one may get gels of apparently the same yield stress, these gels still differ in other aspects such as brittleness and extent of mechanical syneresis. The second type of gel, which includes agar and alginate set by a slow diffusion of calcium ions, is characterized by an increase in gel strength the higher the gum concentration.

food science & technology,chemistry, applied
Food Gel Emulsions: Structural Characteristics and Viscoelastic Behavior

Gabriel Lorenzo,Noemí Zaritzky,Alicia Califano

DOI: https://doi.org/10.1007/978-3-319-94625-2_18

2018-01-01

Abstract:If the continuous phase of an emulsion or foam is a semisolid system, these systems can be described as ‘filled gels’ or ‘composite solids’. Gel emulsions are widely used in different industries like cosmetic, pharmaceutical, and food, among others. Typical examples are cheese, many desserts, sausages, low-fat mayonnaises and bakery products. The aggregation and cross-linking of protein and polysaccharides molecules into three-dimensional solid-like networks (‘gels’) is one of the most important mechanisms for developing microstructure with desirable textural attributes. Due to their elastic characteristics, oil droplets can be kept in suspension avoiding creaming. The structure and the rheological properties of gel emulsions are dependent on the nature of the interactions between the emulsifiers adsorbed on the surface of the droplets that fill the emulsion and the biopolymeric network formed in the aqueous phase. The present chapter deals with the viscoelastic behavior of o/w gel emulsions containing either polysaccharides or proteins in the aqueous phase. Two case studies are discussed, i.e., emulsions with low lipid content, stabilized with bovine gelatin of different molecular weights and heat-induced gel emulsions containing high acyl gellan gum. Small amplitude oscillatory shear tests (stress and frequency sweeps) and transient studies (creep-recovery) were performed over the different matrices and modeled to interpret the structural characteristics of the gel emulsions. The Broadened Baumgaertel-Schausberger-Winter spectrum was used to represent the linear viscoelastic behavior of the continuous phase and the emulsified system. Relaxation spectra were validated using creep experiments.
Gelation as condensation frustrated by hydrodynamics and mechanical isostaticity

Hideyo Tsurusawa,Mathieu Leocmach,John Russo,Hajime Tanaka

DOI: https://doi.org/10.1126/sciadv.aav6090

2018-04-12

Abstract:Colloidal gels have unique mechanical and transport properties that stem from their bicontinous nature, in which a colloidal network is intertwined with a viscous solvent, and have found numerous applications in foods, cosmetics, construction materials, and for medical applications, such as cartilage replacements. So far, our understanding of the process of colloidal gelation is limited to long-time dynamical effects, where gelation is viewed as a phase separation process interrupted by the glass transition. However, this picture neglects two important effects: the influence of hydrodynamic interactions, and the emergence of mechanical stability. With confocal microscopy experiments, here we successfully follow the entire process of gelation with a single-particle resolution, yielding time-resolved measures of internal stress and viscoelasticity from the very beginning of the aggregation process. First, we demonstrate that the incompressible nature of a liquid component constrains the initial stage of phase separation, assisting the formation of a percolated network. Then we show that this network is not mechanically stable and undergoes rearrangements driven by self-generated internal stress. Finally, we show that mechanical metastability is reached only after percolation of locally isostatic environments, proving isostaticity a necessary condition for the stability and load bearing ability of gels rather than the glass transition. Our work reveals the crucial roles of momentum conservation in gelation in addition to the conventional purely out-of-equilibrium thermodynamic picture.

Soft Condensed Matter
Thermoresponsive oil-continuous gels based on double-interpenetrating colloidal-particle networks

Braulio A Macias-Rodriguez,Roland Gouzy,Corentin Coulais,Krassimir P Velikov,Braulio Macias-Rodriguez,Krassimir Petkov Velikov

DOI: https://doi.org/10.1039/d3sm01582c

IF: 4.046

2024-02-10

Soft Matter

Abstract:Gels composed of multicomponent building blocks offer promising opportunities for the development of novel soft materials with unique and useful structures. While interpenetrating polymer networks have been extensively studied and applied in the creation of these gels, equivalent strategies utilizing colloidal particles have received limited scientific and technological attention. This study presents a novel class of thermo-responsive apolar double gels from interpenetrating networks of attractive colloidal silica and lipid particles. These double gels are easily assembled and suitable for the fabrication of 3D-printed edible soft constructs. Emphasis is focused on the rheological properties and structure emerging on the dilute regime (φ ≲ 0.1). Rheological investigations demonstrate that double gels exhibit greater stiffness and resilience to yielding compared to their single lipid gel counterparts. The scaling behavior of the oscillatory linear shear moduli and the critical strain for yielding with volume fraction remain comparable between single and double gels. Creep yielding in double gels exhibits two exponential decay regimes, suggesting the presence of thicker gel strands undergoing flow. Visualization and quantification of the quiescent microstructure confirms the existence of such denser aggregates devoid of larger clusters due to steric hindrance of interpenetrating networks in double gels. This is in stark contrast to lipid single gels where aggregates grow unrestricted into larger clusters. Our study constitutes the first demonstration on the assembly of double gel networks as a promising avenue for the design of novel soft materials and foods with tailored structure and mechanics.

polymer science,chemistry, physical,materials science, multidisciplinary,physics
Interfacial viscoelastic moduli in a weak gel

Ahmad Jaber,Thibault Roques-Carmes,Philippe Marchal,Tayssir Hamieh,Lazhar Benyahia

DOI: https://doi.org/10.1016/j.jcis.2022.04.047

2022-09-15

Abstract:Hypothesis: The measurement of interfacial viscoelastic moduli provides information on the ability of surface-active agents to texture the interface. However, the contribution of the bulk rheology cannot be ignored in particular when the continuous phase exhibits a gel-like behavior, even with low modulus. Experiments: Between 2 and 6 g/L, κ-carrageenan aqueous solutions have no significant activities at interfaces. At low concentrations or high temperatures, they behave like Newtonian liquids. Upon heating or cooling, a reversible liquid/gel transition appears with a hysteresis where the rheological behavior can be easily modulated by adjusting κ-carrageenan concentration. The frequency dependence of bulk and interfacial viscoelastic moduli are determined using a conventional shear rheometer and a drop tensiometer with a polyisobutene oil, respectively. Findings: The effect of concentration and temperature is analyzed and the frequency dependence of interfacial moduli is correlated with those of the bulk. In presence of a gelled κ-carrageenan solutions, an elastic behavior of the interface appears and strengthens as the elastic modulus of the suspended phase is high. It turns out that the oscillating pendant drop method could be a sensitive indicator of the presence of very weak gels, even hardly detected by a shear classical rheometry.
Rheology of protein-stabilised emulsion gels envisioned as composite networks. 1 -- Comparison of pure droplet gels and protein gels

Marion Roullet,Paul S. Clegg,William J. Frith

DOI: https://doi.org/10.1016/j.jcis.2020.05.004

2020-07-09

Abstract:Protein-stabilised emulsion gels can be studied in the theoretical framework of colloidal gels, because both protein assemblies and droplets may be considered as soft colloids. These particles differ in their nature, size and softness, and these differences may have an influence on the rheological properties of the gels they form. Pure gels made of milk proteins (sodium caseinate), or of sub-micron protein-stabilised droplets, were prepared by slow acidification of suspensions at various concentrations. Their microstructure was characterised, their viscoelasticity, both in the linear and non-linear regime, and their frequency dependence were measured, and the behaviour of the two types of gels was compared. Protein gels and droplet gels were found to have broadly similar microstructure and rheological properties when compared at fixed volume fraction, a parameter derived from the study of the viscosity of the suspensions formed by proteins and by droplets. The viscoelasticity displayed a power law behaviour in concentration, as did the storage modulus in frequency. Additionally, strain hardening was found to occur at low concentration. These behaviours differed slightly between protein gels and droplet gels, showing that some specific properties of the primary colloidal particles play a role in the development of the rheological properties of the gels.

Soft Condensed Matter,Materials Science
Eye Examination Testability in Children with Autism and in Typical Peers

R. Coulter,A. Bade,Y. Tea,G. Fecho,Deborah M. Amster,E. Jenewein,Jacqueline Rodena,K. K. Lyons,G. Mitchell,Nicole Quint,S. Dunbar,M. Ricamato,Jennie S. Trocchio,B. Kabat,C. García

DOI: https://doi.org/10.1097/OPX.0000000000000442

2014-12-22

Optometry and Vision Science

Abstract:Purpose To compare testability of vision and eye tests in an examination protocol of 9- to 17-year-old patients with autism spectrum disorder (ASD) to typically developing (TD) peers. Methods In a prospective pilot study, 61 children and adolescents (34 with ASD and 27 who were TD) aged 9 to 17 years completed an eye examination protocol including tests of visual acuity, refraction, convergence (eye teaming), stereoacuity (depth perception), ocular motility, and ocular health. Patients who required new refractive correction were retested after wearing their updated spectacle prescription for 1 month. The specialized protocol incorporated visual, sensory, and communication supports. A psychologist determined group status/eligibility using DSM-IV-TR (Diagnostic and Statistical Manual of Mental Disorders, Fourth Edition, Text Revision) criteria by review of previous evaluations and parent responses on the Social Communication Questionnaire. Before the examination, parents provided information regarding patients’ sex, race, ethnicity, and, for ASD patients, verbal communication level (nonverbal, uses short words, verbal). Parents indicated whether the patient wore a refractive correction, whether the patient had ever had an eye examination, and the age at the last examination. Chi-square tests compared testability results for TD and ASD groups. Results Typically developing and ASD groups did not differ by age (p = 0.54), sex (p = 0.53), or ethnicity (p = 0.22). Testability was high on most tests (TD, 100%; ASD, 88 to 100%), except for intraocular pressure (IOP), which was reduced for both the ASD (71%) and the TD (89%) patients. Among ASD patients, IOP testability varied greatly with verbal communication level (p < 0.001). Although IOP measurements were completed on all verbal patients, only 37.5% of nonverbal and 44.4% of ASD patients who used short words were successful. Conclusions Patients with ASD can complete most vision and eye tests within an examination protocol. Testability of IOPs is reduced, particularly for nonverbal patients and patients who use short words to communicate.
Structural and mechanical properties of biopolymer gels

Allan H. Clark,Simon B. Ross-Murphy

DOI: https://doi.org/10.1007/bfb0023332

2024-01-31

Biopolymers

Abstract:The structural and mechanical properties of gels formed from biopolymers are discussed both in terms of the techniques used to characterise these systems, and in terms of the systems themselves. The techniques included are spectroscopic, chiroptical and scattering methods, optical and electron microscopy, thermodynamic and kinetic methods and rheological characterisation. The systems considered are presented in order of increasing complexity of secondary, tertiary and quaternary structure, starting with gels which arise from essentially ‘disordered’ biopolymers via formation of ‘quasicrystalline’ junction zones (e.g. gelatin, carrageenans, agarose, alginates etc.), and extending to networks derived from globular and rod-like species (fibrin, globular proteins, caseins, myosin) by a variety of crosslinking mechanisms. Throughout the text, efforts are made to pursue the link (both from experiment and from theory) between the structural methods and mechanical measurements. As far as we are aware this is the first major Review of this area since that of J. D. Ferry in 1948 — The interest shown by polymer physicists in more complex biochemical systems, and the multi-disciplinary approaches now being applied in this area, make the format adopted here, in our opinion, the most logical and appropriate.

biochemistry & molecular biology,biophysics
Synergistic gelation of xanthan gum with locust bean gum: a rheological investigation

G Copetti,M Grassi,R Lapasin,S Pricl

DOI: https://doi.org/10.1023/a:1018523029030

Abstract:Many industrial products often include in their formulation more than one polysaccharide to achieve the desired properties during and after processing. Many such mixed systems behave as would be expected from the known properties of the individual polymers. In others, however, their properties are superior to those of either component alone, or may be qualitatively different. In many polysaccharide systems, the combination of a gelling polymer with a nongelling one gives rise to strong synergistic effects, as a consequence of interaction among different chain polymers and formation of mixed junction zones. Probably, the most exploited mixed gels, especially by the food industry, are those involving the microbial polysaccharide xanthan gum (XG) and the plant galactomannans, like locust bean gum (LBG). Concentrated aqueous systems of LBG and XG display quite different rheological properties: the former show the behaviour typical of hyperentangled macromolecular solutions, whereas the flow and viscoelastic properties of XG systems correspond to those of tenuous, weak-gel networks. Interestingly, when mixed together these macromolecules interact to form a firm, thermoreversible gel with synergistic effects. In the present paper we report the results of a thorough investigation of both polymer concentration and temperature effects on the rheological properties of mixed LBG-XG systems in 20 mM KCl under continuous and oscillatory flow conditions. Under continuous shear at 25 degrees C, pure LBG shows the flow properties of a macromolecular solution, with a shear-thinning behaviour and a Newtonian region at low shear rates, whereas the rheological behaviour of XG and all LX mixed systems is that typical of weak-gels. Furthermore, in the mixed systems the viscosity values do not increase monotonically with increasing xanthan concentration, but the synergistic effect has a maximum in accordance with the XG:LBG ratio 1:1. As the temperature is increased from 25 degrees C to 85 degrees C, whilst the LBG system do not show any qualitative change but there is only a parallel, downward shift of viscosity values, in the case of xanthan there is a dramatic change in the corresponding curve profiles, due to the thermally induced helix-coil conformational transition. The differences in the rheological behaviour of the systems examined can be better shown through dynamic tests at 25 degrees C. The strain sweeps performed at constant frequency of oscillation reveal that the mixed systems show higher sensitivity to strain amplitude, and lower strain values must be attained to ensure linear viscoelastic properties. The mechanical spectra clearly show the influence of composition on the viscoelastic properties of these biopolymer systems. All LX systems show the mechanical spectra typical of polysaccharide gels: G' is always much greater than G" and is nearly independent of the applied frequency over a wide frequency range. In addition, the marked gap between the elastic responses of the pure LBG and the LX 1:3 systems demonstrates the strong effect of the initial addition of xanthan to the pure LBG, especially in the low frequency range, whereas the highest synergistic effect is attained for the LX 1:1 system. A comprehensive description of the frequency dependence of both moduli can be suitably obtained through the four-parameter Friedrich model, which belongs to the class of fractional derivative approaches viscoelasticity. The same thermal effect is observed for the XG and all LX mixed systems considered, indicating a progressive change from the behaviour of a typical gel to that of a quasi-solution state, when temperature is increased from 25 degrees C to 85 degrees C. Among all mixed systems, the LX 1:1 has the highest values of the moduli at any temperature considered, and is characterized by the highest gel-sol transition temperature. (ABSTRACT TRUNCATED)
Special Section on the 2011 IEEE International Symposium on Medical Measurements and Applications

S. Rapuano,W. Moer

DOI: https://doi.org/10.1109/TIM.2012.2193169

IF: 5.6

2012-05-01

IEEE Transactions on Instrumentation and Measurement

Abstract:The six papers in this special section were originally presented at the 2011 IEEE International Symposium on Medical Measurements and Applications (MeMeA 2011), held on May 30-31, 2011 in Bari, Italy.
Mechanical Properties and Failure Behavior of Physically Assembled Triblock Copolymer Gels with Varying Midblock Length

Satish Mishra,Rosa M. Badani Prado,Song Zhang,Thomas E. Lacy,Xiaodan Gu,Santanu Kundu

DOI: https://doi.org/10.1002/polb.24860

2019-01-01

Abstract:ABSTRACTMechanical properties including the failure behavior of physically assembled gels or physical gels are governed by their network structure. To investigate such behavior, we consider a physical gel system consisting of poly(styrene)‐poly(isoprene)‐poly(styrene)[PS‐PI‐PS] in mineral oil. In these gels, the endblock (PS) molecular weights are not significantly different, whereas, the midblock (PI) molecular weight has been varied such that we can access gels with and without midblock entanglement. Small angle X‐ray scattering data reveals that the gels are composed of collapsed PS aggregates connected by PI chains. The gelation temperature has been found to be a function of the endblock concentration. Tensile tests display stretch‐rate dependent modulus at high strain for the gels with midblock entanglement. Creep failure behavior has also been found to be influenced by the entanglement. Fracture experiments with predefined cracks show that the energy release rate scales linearly with the crack‐tip velocity for all gels considered here. In addition, increase of midblock chain length resulted in higher viscous dissipation leading to a higher energy release rate. The results provide an insight into how midblock entanglement can possibly affect the mechanical properties of physically assembled triblock copolymer gels in a midblock selective solvent. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019, 57, 1014–1026
Relationship between Rheology and Structure of Interpenetrating, Deforming and Compressing Microgels

Gaurasundar M. Conley,James L. Harden,Frank Scheffold

DOI: https://doi.org/10.1038/s41467-019-10181-5

2018-11-05

Abstract:Thermosensitive microgels are widely studied hybrid systems combining properties of polymers and colloidal particles in a unique way. Due to their complex morphology their interactions and packing, and consequentially the viscoelastcity of suspensions made from microgels, are still not fully understood, in particular under dense packing conditions. Here we study the frequency-dependent linear viscoelastic properties of dense microgel suspensions in conjunction with an analysis of the local particle structure and morphology based on superresolution microscopy. By identifying the dominating mechanisms that control the elastic and dissipative response, we propose a unified framework that can explain the rheology of these widely studied soft particle assemblies from the onset of elasticity deep into the overpacked regime. Our results clarify the transition and coupling between the regime dominated by fuzzy shell interactions and the one controlled by the densely cross-linked core.

Soft Condensed Matter
Mechanical properties of agarose hydrogels tuned by amphiphilic structures

Martin Kadlec,Miloslav Pekař,Jiří Smilek

DOI: https://doi.org/10.1016/j.colsurfa.2024.134791

IF: 5.518

2024-07-19

Colloids and Surfaces A Physicochemical and Engineering Aspects

Abstract:Agarose is a biocompatible polysaccharide that is capable to form physically cross-linked hydrogels in aqueous dispersion. These materials offer a wide range of applications and are commonly used in the food industry or electrophoresis. Moreover, due to their favourable characteristics (biocompatibility, high water absorption, porosity), agarose hydrogels have recently also found applications also in drug delivery systems, wound dressing, and extracellular matrix (ECM) modelling. This paper presents a comprehensive rheological characterization of agarose hydrogels with various self-assembled amphiphilic structures (CTAB, TTAB, SDS, Tween 20) acting as simple membrane structure models. These findings demostrated that the presence of surfactants of diverse charge above their critical micellar concentration (CMC) can enhance hydrogel mechanical properties. Moreover, pronounced enhancement was observed for cationic surfactant, and even concentrations below CMC resulted in a higher stiffness of the hydrogel. Therefore, both the electrostatic effect and the amphiphilic structure effect can have a significant impact on the rheological properties on agarose hydrogels. These findings are of a significant interest in the field of polymer and surfactants interactions, since agarose is widely considered essentially uncharged. However, it is assumed, that traces of negatively charged groups on the agarose backbone can have a significant impact when interacting with oppositely charged surfactants. Moreover, these findings could be beneficial for better understanding of interaction of polysaccharides (e.g. agarose) and self-assembled amphiphilic structures and can also be considered as a crude model of ECM in which membrane structures are embedded.

chemistry, physical
Small and large oscillatory shear behaviors of gelatin/starch system regulated by amylose/amylopectin ratio

Dongling Qiao,Yuchun Huang,Guohua Zhao,Yuyan Zhang,Xinran Hou,Binjia Zhang,Fatang Jiang

DOI: https://doi.org/10.1016/j.foodhyd.2023.108780

IF: 10.7

2023-04-17

Food Hydrocolloids

Abstract:This work explores the influence of starch amylose/amylopectin ratio on the gel-related features of gelatin/starch system using small and large amplitude oscillation shear methods. The higher self-aggregation and self-entanglement ability of amylose reduced the miscibility of gelatin and starch, and increases zero-shear viscosity ( ŋ 0 ) and reduces sol-gel transition temperature ( T gel ) by enhancing the difficulty of molecule movement and thus the difficulty of gel formation. The gelatin/amylopectin-rich system has higher gel hardness and wider linear viscoelastic region, which are related to the higher integrity and uniformity of network structure. The gelatin/amylose-rich system shows enhanced ability to resist deformation against external shear forces (suggested by higher storage and complex modulus) under small amplitude oscillatory shear (SAOS), which is ascribed to the larger rigidity and entanglement degree of amylose. At strain amplitude up to 50% (middle amplitude oscillatory shear, MAOS), gelatin/amylose-rich system exhibits reduced structure recovery ability (reflected by larger semi-minor axis of ellipse, and lower strain amplitude for inflexion of elastic stress) under MAOS, but enhances restructuring capacity at strains of 500% and 1000% (large amplitude oscillatory shear, LAOS) (indicated by occurrence of secondary loop) than gelatin/amylopectin-rich system. Those seemingly contradictory phenomena are correlated with the preference of hydrogen bond forming ability among amylose rather than with gelatin. This weakens interactions between amylose and gelatin and thus inhibits recovery of bulk structure under MAOS, but is favor for the formation of amylose aggregations, which is helpful for the local structure restructuring and thus enhances structure restructuring capacity under LAOS. The results help us comprehensively understand the gel-related properties of gelatin/starch system and are valuable for rational design of gelatin/starch systems with improved gel-related features.

food science & technology,chemistry, applied

Fibrinolysis and coagulation abnormalities in systemic lupus erythematosus

Glass Transition in Gels

Competition among physical, chemical, and hybrid gelation mechanisms in biopolymers

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Effect of Polymer Gel Elasticity on Complex Coacervate Phase Behavior

Oscillatory rheometry for elucidating the influence of non-network biopolymer aggregation on pectin-gelatin composite gels

Link between morphology, structure and interactions of composite microgels

Effect of hydrocolloid and minerals content on the mechanical properties of gels

Food Gel Emulsions: Structural Characteristics and Viscoelastic Behavior

Gelation as condensation frustrated by hydrodynamics and mechanical isostaticity

Thermoresponsive oil-continuous gels based on double-interpenetrating colloidal-particle networks

Interfacial viscoelastic moduli in a weak gel

Rheology of protein-stabilised emulsion gels envisioned as composite networks. 1 -- Comparison of pure droplet gels and protein gels

Eye Examination Testability in Children with Autism and in Typical Peers

Structural and mechanical properties of biopolymer gels

Synergistic gelation of xanthan gum with locust bean gum: a rheological investigation

Special Section on the 2011 IEEE International Symposium on Medical Measurements and Applications

Mechanical Properties and Failure Behavior of Physically Assembled Triblock Copolymer Gels with Varying Midblock Length

Relationship between Rheology and Structure of Interpenetrating, Deforming and Compressing Microgels

Mechanical properties of agarose hydrogels tuned by amphiphilic structures

Small and large oscillatory shear behaviors of gelatin/starch system regulated by amylose/amylopectin ratio