Optimal Resource Allocation for Joint Sensing and Communication: Multiple Targets and Clutters

Ali Kariminezhad,Soheil Gherekhloo,Aydin Sezgin
DOI: https://doi.org/10.48550/arXiv.1902.11117
2019-02-28
Abstract:We study a contactless target probing based on stimulation by a radio frequency (RF) signal. The transmit signal is dispatched from a transmitter equipped with a two-dimensional antenna array. Then, the reflected signal from the targets are received at multiple distributed sensors. The observation at the sensors are amplified and forwarded to the fusion center. Afterwards, the fusion center performs space-time post processing to extract the maximum common information between the received signal and the targets impulse responses. Optimal power allocation at the transmitter and amplification at the sensors is investigated. The sum-power minimization problem turns out to be a non-convex problem. We propose an efficient algorithm to solve this problem iteratively. By exploiting maximum-ratio transmission (MRT), maximum-ratio combining (MRC) of space-time received signal vector is the optimal receiver at sufficiently low signal-to-interference-plus-noise-ratio (SINR). However, zero-forcing (ZF) at the fusion center outperforms MRC at higher SINR demands.
Information Theory
What problem does this paper attempt to address?
The problem that this paper attempts to solve is to optimize resource allocation through joint sensing and communication in an environment with multiple targets and clutter, in order to achieve the identification of material properties. Specifically, the paper focuses on how to minimize the total power consumption of the transmitter and the amplification power of the sensor while ensuring the maximum common information extraction between the received signal and the target impulse response. This problem is transformed into a non - convex optimization problem, namely the total power minimization problem. The paper proposes an effective iterative algorithm to solve this problem and explores the performance comparison of two receiving strategies, maximum - ratio transmission (MRT) and zero - forcing (ZF), under different signal - to - noise ratio conditions. ### Specific description of the problem - **Background**: The paper studies a non - contact target detection technology based on radio - frequency (RF) signal stimulation. The transmitted signal is sent by a transmitter equipped with a two - dimensional antenna array, and the reflected signal is received by multiple distributed sensors. Then these signals are amplified and forwarded to the fusion center for processing. - **Objective**: By optimizing the power allocation of the transmitter and the amplification of the sensor, the total power consumption is minimized under the constraint of the signal - to - interference - plus - noise ratio (SINR) of the received signal. - **Challenge**: The total power minimization problem is a non - convex problem and is difficult to solve directly. In addition, the performance differences of different receiving strategies (such as MRT and ZF) under different SINR conditions need to be evaluated. ### Solution - **Method**: The paper proposes an iterative algorithm to solve the non - convex total power minimization problem. This algorithm uses the geometric programming method to gradually approximate the optimal solution through approximation and optimization. - **Receiving strategy**: The paper analyzes two receiving strategies: - **Maximum - ratio transmission (MRT)**: It performs better under low SINR conditions, but does not consider the influence of interference. - **Zero - forcing (ZF)**: It is superior to MRT under high SINR conditions and improves performance by eliminating interference. ### Main contributions - **Optimization algorithm**: An effective iterative algorithm is proposed to solve the non - convex total power minimization problem. - **Performance analysis**: Through simulation results, the performance differences between the two receiving strategies, MRT and ZF, under different SINR requirements are shown. - **Practical application**: The research results are of great significance for radar system design and material property identification in multi - target environments. ### Formula summary - **SINR expression**: \[ \rho_j=\frac{\delta_j Q_j\left(\sum_{k = 1}^K\alpha_k|g_{jk}|^2\|f_k\|^2\right)^2}{\Sigma_j^{\text{int}}+\Sigma_j^{\text{ns}}+\Sigma_j^{\text{nfc}}} \] where, \[ \Sigma_j^{\text{des}}=\delta_j Q_j\left(\sum_{k = 1}^K\alpha_k|g_{jk}|^2\|f_k\|^2\right)^2 \] \[ \Sigma_j^{\text{int}}=\sum_{i\neq j}\delta_i Q_i\left|\sum_{k = 1}^K\alpha_k g_{jk}g_{ik}^*\|f_k\|^2\right|^2 \] \[ \Sigma_j^{\text{ns}}=\sum_{k = 1}^K\sigma_k^2\alpha_k^2|g_{jk}|^2\|f_k\|^4 \] \[ \Sigma_j^{\text{nfc}}=\sigma_{\text{fc}}^2\sum_{k = 1}^K\alpha_k|g_{jk}|^2\|f_k\|^2 \] - **Optimization problem**: \[ \min_{p_j,\alpha_k,\forall j,k}\sum_{j = 1}^N p_j+\sum_{