Abstract:Despite boasting giant leaps in performance improvement over the years, the current commercial standard, Li-ion batteries, are fast approaching their theoretical limits. Meanwhile, Lithium-Sulfur (Li-S) batteries offering ultra-high theoretical energy density (~2600 Whkg -1 ), cost-effectiveness, and nontoxicity are being seen as promising alternatives. Despite their plentiful advantages, the practicality of Li-S batteries has been largely stymied by several challenges: a) deleterious polysulfide dissolution and ‘shuttle effect’, b) significant volume change of S cathodes during cycling, c) safety concerns with flammable traditional glyme-based electrolyte, and d) the instability of Li anode. To mitigate these challenges, researchers have explored all-solid-state electrolytes, but their poor Li-ion conductivity, high interfacial impedance, and need for expensive, exotic materials and complex fabrication procedures severely limit their practical application. To overcome these challenges, we propose an in-situ gelled polymer-ceramic hybrid silsesquioxane-based electrolyte system. The gelled matrix, thermally crosslinked post cell fabrication, immobilizes the glyme-based liquid electrolyte and exhibits high liquid-like ionic conductivities (1.03 mS.cm -1 ), low interfacial impedance, and high oxidative potential (>4.5V vs. Li/Li + ) . In this study, in addition to vastly decreased flammability, we report superior Li-ion conductivity compared to state-of-art solid-state Li-S electrolytes. This high ionic conductivity translated to a significantly improved specific capacity of 1050 mAh.gS -1 at 0.2 C, elevated Coulombic efficiencies (>98.5%), and elevated rate kinetics. The gelled electrolytes exhibited stable cycling in a large temperature range (-10 o C - 60 o C). Moreover, polysulfide permeation studies and subsequent DFT calculations revealed that the gelled electrolyte exhibited strong chemical absorptivity to lithium polysulfides due to the polar silsesquioxane core, which translated to superior capacity retention (>80% over 200 cycles). Further, post- mortem XPS characterization studies revealed the formation of stable SEI at the anode and cathode, and SEM of cycled anodes showed reduced dendritic formations. Finally, the electrolyte was tested in practical pouch cell architecture, and the cells demonstrated excellent reliability even under mechanical stress. This work successfully reports a robust, rationally designed gelled electrolyte system for developing safe and high-performance quasi-solid state Li-S batteries.

Quasi-Solid-State Electrolyte Synthesized Using a Thiol-Ene Click Chemistry for Rechargeable Lithium Metal Batteries with Enhanced Safety.

Polymer‐Ion Interaction Prompted Quasi‐Solid Electrolyte for Room‐Temperature High‐Performance Lithium‐Ion Batteries

Nonflammable Quasi-Solid-state Electrolyte for Stable Lithium-Metal Batteries

In Situ Fabricated Non‐Flammable Quasi‐Solid Electrolytes for Li‐Metal Batteries

Rationally Designed in-Situ Gelled Polymer-Ceramic Hybrid Electrolyte Enables Superior Performance and Stability in Quasi-Solid-State Lithium-Sulfur Batteries

Enhanced Ionic Conductivity and Interface Stability of Hybrid Solid-State Polymer Electrolyte for Rechargeable Lithium Metal Batteries

Ultrathin, Mechanically Robust Quasi-Solid Composite Electrolyte for Solid-State Lithium Metal Batteries

In Situ Polymerization Design of a Quasi-Solid Electrolyte Enhanced by NMP Additive for Lithium Metal Batteries

Solvent‐Free Electrolyte for High‐Temperature Rechargeable Lithium Metal Batteries

Deep Eutectic Solvent‐Based Solid Polymer Electrolytes for High‐Voltage and High‐Safety Lithium Metal Batteries

Novel Quasi Solid-State Succinonitrile-based Electrolyte with Low-flammability for Lithium-ion Battery

Solid-State Interphases Design for High-Safety, High-Voltage and Long-Cyclability Practical Batteries via Ethylene Carbonate-Free Electrolytes

Lithium Salt Catalyzed Ring-Opening Polymerized Solid-State Electrolyte with Comparable Ionic Conductivity and Better Interface Compatibility for Li-Ion Batteries

A Single‐Ion Conducting Borate Network Polymer as a Viable Quasi‐Solid Electrolyte for Lithium Metal Batteries

Ionic Plastic Crystal-Polymeric Ionic Liquid Solid-State Electrolytes with High Ionic Conductivity for Lithium Ion Batteries

Rational Design of an In-Build Quasi-Solid-state Electrolyte for High-Performance Lithium-Ion Batteries with the Silicon-Based Anode

Non-flammable solvent-free liquid polymer electrolyte for lithium metal batteries

Tuning the Solution Structure of Electrolyte for Optimal Solid-Electrolyte-interphase Formation in High-Voltage Lithium Metal Batteries

In-situ Fabricated Succinonitrile-Based Composite Electrolyte for High-Performance and Safe Solid-State Lithium Batteries

A Unique Hybrid Quasi-Solid-State Electrolyte for Li-O2 Batteries with Improved Cycle Life and Safety

Regulating Micro‐phase Structure in Plastic Crystal Gel Polymer Electrolyte for Quasi‐Solid‐State Lithium Metal Batteries