Abstract:To realize the application potential of molybdenum disulfide (MoS2) in aqueous environments, scalable and efficient methods for the preparation of high-concentration and stable dispersions need to be developed. In this paper, ultrathin MoS2 successfully was synthesized using an in situ-exfoliated bulk MoS2 method in water using ionic liquid crystals (ILCs) as green exfoliating/dispersing agents. The ILCs containing hydrophobic cations and hydrophilic anions not only help to exfoliate bulk MoS2 into ultrathin MoS2 nanosheets but also prevent the re-agglomeration of the ultrathin MoS2 nanosheets in water. MoS2 nanosheets were confined by the ILCs through π–π and C–H···π interactions, preventing direct contact of MoS2 with water. The ILC–MoS2 dispersion exhibited remarkable dispersion stability exceeding 8 months at room temperature. Moreover, the ILC–MoS2 dispersion has been successfully proven to be an excellent water-based lubricant, where the ILCs form a lubricant film on the friction surface through electrostatic interactions and MoS2 increases the load-bearing capacity of the lubricant film due to its high modulus, resulting in an 84.9% reduction in the coefficient of friction compared to pure water. The method is expected to provide a new idea for the preparation and application of MoS2.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acssuschemeng.1c08434.Comparison with previous publications; photographs of bulk MoS2, ILC, and ILC–MoS2; photographs of the contact angle of ILCx on bulk MoS2; photographs and concentration of the ILCx–MoS2 dispersion; AFM image of ILC300–MoS2; digital images of the ILC300–MoS2 dispersion after being allowed to stand for different months; TSI index analysis of different parts of the ILC300–MoS2 dispersion; optical images for the wear track width of ILC300–MoS2 for different lateral sizes; average friction coefficient and wear rate of the ILC300–MoS2 dispersion with an average lateral size of 289 nm under different loads and different rotating speeds; optical images for the wear track width of water, ILCs, and ILC300–MoS2 with an average lateral size of 289 nm; and SEM images of the wear surface for pure water and ILCs in water(PDF)1 mL of the ILC300–MoS2 dispersion dropped into 200 mL of deionized water (AVI)This article has not yet been cited by other publications.

Systematic investigation on the surfactant‐assisted liquid phase exfoliation of MoS2 and WS2 in water for sustainable 2D material inks

Investigating the Exfoliation Behavior of MoS2 and Graphite in Water: A Comparative Study

High-yield exfoliation of MoS2 nanosheets by a novel spray technique and the importance of soaking and surfactants

Surface Tension Components Based Selection of Cosolvents for Efficient Liquid Phase Exfoliation of 2D Materials

Direct Exfoliation of High‐Quality, Atomically Thin MoSe2 Layers in Water

Sonochemical edge functionalisation of molybdenum disulfide

Steer the Rheology of Solvent with Little Surfactant to Exfoliate MoS<sub>2</sub> Nanosheet by Liquid Phase Exfoliation Method

Liquid Phase Exfoliation of Two-Dimensional Materials by Directly Probing and Matching Surface Tension Components.

Single-Molecule MoS2–Polymer Interaction and Efficient Aqueous Exfoliation of MoS2 into Single Layer

Surface Tension Components Ratio: an Efficient Parameter for Direct Liquid Phase Exfoliation

Large-scale Production of Defect-Free MoS2 Nanosheets Via Pyrene-Assisted Liquid Exfoliation

Exfoliation of 2D materials by saponin in water: Aerogel adsorption / photodegradation organic dye

Surfactant-free Exfoliation of Multilayer Molybdenum Disulfide Nanosheets in Water.

Surfactant-Free Polar-to-Non-Polar-Phase Transfer of Exfoliated MoS2 Two-Dimensional Colloids

Ionic Liquid Crystals Confining Ultrathin MoS 2 Nanosheets: A High-Concentration and Stable Aqueous Dispersion

Enhanced Exfoliation of Biocompatible MoS2 Nanosheets by Wool Keratin

Facile And Green Production Of Impurity-Free Aqueous Solutions Of Ws2 Nanosheets By Direct Exfoliation In Water

From Bulk Molybdenum Disulfide (MoS2) to Suspensions of Exfoliated MoS2 in an Aqueous Medium and Their Applications

High-efficiency exfoliation of layered materials into 2D nanosheets in switchable CO2/Surfactant/H2O system

Aqueous Phase Exfoliation of Two-Dimensional Materials Assisted by Thermoresponsive Polymeric Ionic Liquid and Their Applications in Stimuli-Responsive Hydrogels and Highly Thermally Conductive Films

Dimethyl 2‐Methylglutarate (Iris): A Green Platform for Efficient Liquid‐Phase Exfoliation of 2D Materials