Abstract:The finite element (FE) foot model can help estimate pathomechanics and improve the customized foot orthoses design. However, the procedure of developing FE models can be time-consuming and costly. This study aimed to develop a subject-specific scaled foot modelling workflow for the foot orthoses design based on the scanned foot surface data. Six participants (twelve feet) were collected for the foot finite element modelling. The subject-specific surface-based finite element model (SFEM) was established by incorporating the scanned foot surface and scaled foot bone geometries. The geometric deviations between the scaled and the scanned foot surfaces were calculated. The SFEM model was adopted to predict barefoot and foot-orthosis interface pressures. The averaged distances between the scaled and scanned foot surfaces were 0.23 ± 0.09 mm. There was no significant difference for the hallux, medial forefoot, middle forefoot, midfoot, medial hindfoot, and lateral hindfoot, except for the lateral forefoot region ( p = 0.045). The SFEM model evaluated slightly higher foot-orthoses interface pressure values than measured, with a maximum deviation of 7.1%. These results indicated that the SFEM technique could predict the barefoot and foot-orthoses interface pressure, which has the potential to expedite the process of orthotic design and optimization.

What problem does this paper attempt to address?

The problem that this paper attempts to solve is how to design custom orthotics by integrating 3D scanning technology and individualized finite element modeling processes to improve the design efficiency and accuracy of foot orthotics. Specifically, the research aims to develop an individualized scaled foot modeling workflow based on scanned foot surface data for the design of foot orthotics. This includes: 1. **Propose and validate the scanned - foot - surface - based finite element model (SFEM)**: By using four different custom - scaling methods, the researchers hope to validate the effectiveness and accuracy of these methods in generating individualized foot models. 2. **Evaluate the functional effect of SFEM in foot orthotic design**: By predicting the pressure at the interface of the bare foot and the foot orthotic, evaluate the performance of the SFEM model in practical applications. ### Research Background - **Prevalence of foot pain**: The prevalence of foot pain among adults is between 17% and 42% and is considered a risk factor affecting gait, balance, fall risk, and quality of life. - **Impact of foot pain**: Foot pain not only affects foot alignment, joint kinematics, and muscle activation but may also lead to dynamic instability and misalignment of the lower - limb joints, thereby accelerating the occurrence of lower - limb dysfunction and pain. - **Limitations of existing solutions**: Although pre - fabricated and custom - made foot orthotics are widely used to manage foot pain, the traditional custom - made orthotic production process is complex, time - consuming, and costly. Although 3D printing technology has simplified the production process, it is still difficult to modify the shape of the orthotic. ### Research Methods - **Participant information**: The study recruited 6 participants (12 feet), aged between 18 and 30 years old, with a BMI below 30 kg/m². - **Experimental protocol**: Use a 3D foot - surface scanner to collect foot geometry data and use the F - scan system to measure plantar pressure. - **Custom foot scaling**: Through a non - linear scaling method, match the template foot model with the scanned foot surface to generate an individualized foot bone geometry. - **Finite element model**: Use Abaqus software to construct a finite element model of the ankle - foot joint, including the skin layer, bone structure, and soft tissue. ### Main Results - **Geometric error analysis**: Among the four different scaling methods, the methods combining RBFPT and RBFST with the thin - plate basis function (THI) performed the best, with an average geometric error of 0.23 ± 0.09 mm. - **Bare - foot plantar pressure prediction**: There were no significant differences between the predicted and measured values in most areas, but there were significant differences in the lateral forefoot area (p = 0.045). - **Foot - orthotic - interface - pressure prediction**: The foot - orthotic - interface - pressure values predicted by the SFEM model were slightly higher than the measured values, with a maximum deviation of 7.1%. ### Conclusion The scanned - foot - surface - based finite element model (SFEM) proposed in this study can efficiently and accurately predict the foot - pressure distribution, providing guidance for the design of custom - made pressure - relieving foot orthotics. Through the non - linear scaling method, the researchers successfully generated individualized foot models, and their prediction results are in good agreement with the actual measured values.

Custom orthotic design by integrating 3D scanning and subject-specific FE modelling workflow

Biomechanical Design of Lightweight Full Contacted Insole Based on Structural Anisotropy Bespoke

Process Planning for the Fuse Deposition Modeling of Ankle-Foot-Othoses

Simplified versus geometrically accurate models of forefoot anatomy to predict plantar pressures: A finite element study

Customized Design for Ergonomic Products Via Additive Manufacturing Considering Joint Biomechanics

Footwear Design for Hallux Valgus: A Virtual Prototyping with Finite Element Modeling

Different Design Feature Combinations of Flatfoot Orthosis on Plantar Fascia Strain and Plantar Pressure: A Muscle-Driven Finite Element Analysis With Taguchi Method

Strategies Towards Rapid Generation of Forefoot Model Incorporating Realistic Geometry of Metatarsals Encapsulated into Lumped Soft Tissues for Personalized Finite Element Analysis

A three-dimensional finite element foot-ankle model and its personalisation methods analysis

A hybrid statistical morphometry free-form deformation approach to 3D personalized foot-ankle models

A Three-Dimensional Printed Foot Orthosis for Flexible Flatfoot: An Exploratory Biomechanical Study on Arch Support Reinforcement and Undercut

Finite Element Parametric Design of Hallux Valgus Orthosis Based on Orthogonal Analysis

In-silico techniques to inform and improve the personalized prescription of shoe insoles

Evaluation Fitness of Footwear Using Hybrid Simulation

Influence of arch support heights on the internal foot mechanics of flatfoot during walking: A muscle-driven finite element analysis

Effect of 3D printed foot orthoses stiffness and design on foot kinematics and plantar pressures in healthy people

Foot Orthosis and Sensorized House Slipper by 3D Printing

Advancing Lower Limb Prosthetics: Custom Design, Simulation, and Experimental Evaluation

Understanding the role of foot biomechanics on regional foot orthosis deformation in flatfoot individuals during walking

Parametric modeling and performance analysis of a personalized insole based on 3D scanning and selective laser sintering

3-D Foot Measurements Using Laser-Line Scanning