Abstract:In order to improve the full utilization of wheat straw, to enhance the mechanical properties of gypsum board and to increase the fire resistance of wood-based gypsum board, a new preparation process of gypsum-based composites with wheat straw was put forward in this study. The thick and small wheat straw fiber were used as the reinforcing materials in gypsum-based composites, and their dimension were in the range of 0.30-0.60 and 0.18-0.30 mm, respectively. The gypsum was employed as the continuous phase in the composites. The ambient temperature curing structural adhesive was used to replace the traditional gypsum retarder in the new preparation process of gypsum-based composites. The preparation process consisted of an initial forming stage for initial strength and a curing stage, where the objectives were gypsum hydration and the strength further increased, respectively. Compared with the conventional gypsum composites with Chinese fir fiber and Chinese fir particle, the mechanical properties and fire resistance of gypsum-based composites by adding wheat straw fiber with different dimension were tested and analyzed. The results showed that the physical and mechanical properties of gypsum-based composites with small wheat straw fiber were lower than those of gypsum-based composites with Chinese fir fiber, but were better than gypsum-based composites with thick wheat straw fiber. The internal bond strength, modulus of rupture, modulus of elasticity and thickness swelling of gypsum-based composites with small wheat straw fiber were 0.33 MPa, 7.1 MPa, 2 370 MPa and 2.82%, respectively, and could meet the requirements of gypsum particleboard standard. According to the lower thermal conductivity and higher ash content of wheat straw than wood materials, the time to ignition of gypsum-based composites with wheat straw was higher than that of gypsum-based composites with Chinese fir fiber, and there was no obvious peak heat release rate in the fire resistance test. Compared with the gypsum-based with Chinese fir fiber and Chinese fir particle, the total heat release of gypsum-based composites with small wheat straw fiber was 48.18% and 35.87% lower, respectively. The main peak of CO2 production rate was 42.25% and 38.81% lower than that of Chinese fir fiber and particle gypsum composites, respectively. The main peak of CO production rate was comparable to wood-gypsum composites. The weight percent retains of small wheat straw fiber gypsum composites was slightly higher than that of Chinese fir gypsum composites, and the appearance after burning test was more complete and the degree of carbonization was lighter obviously. Due to the smooth outer surface of the wheat straw, the gypsum was mainly attached to the internal surface of the wheat straw by microscopic observation using scanning electron microscope. Therefore, the small straw fiber could increase the contact area between the internal surface and the gypsum, which indicated the inherent reason for the better physical and mechanical properties of small wheat straw fiber gypsum composites. The smooth outer surface of the wheat straw was almost covered with SiO2, which also explained the superior fire resistance of wheat straw gypsum composites. The study can be a reference for the performance improving on the gypsum-based composites with wheat straw fiber and its application in project.

Eco-friendly lightweight composite prepared with geopolymer and wheat straw

Synthesis of Geopolymers Using Municipal Solid Waste Incineration Fly Ash and Construction and Demolition Waste: Mechanical and Thermal Activation

Impacts of Alkaline Washing Pretreatment on Municipal Solid Waste Incineration Fly Ash (MSWI FA) and Resulting Geopolymers

Utilization of Municipal Solid Waste Incineration (MSWIFA) in Geopolymer Concrete: A Study on Compressive Strength and Leaching Characteristics

Wheat straw fibre based semi-IPN composite: Preparation and evaluation as a matrix for water and fertilizer release and in slope reinforcement

Synthesis of geopolymer using municipal solid waste incineration fly ash and steel slag: Hydration properties and immobilization of heavy metals

Utilization of municipal solid waste incineration fly ash with red mud-carbide slag for eco-friendly geopolymer preparation

Synchronous recycling of multi-source solid wastes for low-carbon geopolymer preparation: Primary factors identification and feasibility assessment

Preparation and Properties of Lightweight Geopolymer by Bio-Based Foaming Agent

Effect of fly ash cenospheres on properties of multi-walled carbon nanotubes and polyvinyl alcohol fibers reinforced geopolymer composites

Physical and mechanical properties and micro characteristics of fly ash-based geopolymer paste incorporated with waste Granulated Blast Furnace Slag (GBFS) and functionalized Multi-Walled Carbon Nanotubes (MWCNTs)

Effect of Single and Synergistic Reinforcement of PVA Fiber and Nano-SiO2 on Workability and Compressive Strength of Geopolymer Composites

Hybrid Composites from Wheat Straw, Inorganic Filler, and Recycled Polypropylene: Morphology and Mechanical and Thermal Expansion Performance

Utilizing waste geopolymer powder as partial cement replacement for sustainable cement mortar: Micro-macro properties and modification

Synthesis and Characterization of Red Mud and Rice Husk Ash-Based Geopolymer Composites

Sustainable packaging biocomposites from polylactic acid and wheat straw: Enhanced physical performance by solid state shear milling process

Immobilization of MSWI Fly Ash Through Geopolymerization: Effects of Water-Wash

Synthesis of metakaolin-based geopolymer foamed materials using municipal solid waste incineration fly ash as a foaming agent

Synergistic utilization of industrial waste red mud and rice husk ash for eco-friendly geopolymer preparation: enhancing strength and mitigating hazardous leaching

Mechanical properties and fire resistance of gypsum-based composites with wheat straw

Preparation of functional geopolymers from municipal solid waste incineration fly ash: An approach combining experimental and computational simulation studies