Abstract:Lithium-rich layered oxides have attracted much attention due to their high discharge capacity (>250 mA h·g–1). However, lithium-rich layered cathodes suffer from poor rate capabilities and voltage decay, which seriously limit their practical application. Herein, a unique @spinel double-spinel shell heterostructure is designed and successfully synthesized via coprecipitation and high-temperature solid-phase methods. In particular, lithium-rich layered oxides show good rate capabilities and high capacity retention when the molar amount of cobalt acetate and manganese acetate is 5%. After 100 cycles at 0.2 C, a discharge capacity of 232 mA h g–1 and a capacity retention of 92.7% can be obtained. The superior electrochemical performance of the in situ-transformed Li-rich layered cathode can be attributed to the unique three-dimensional diffusion channels for Li ions of the surface spinel phase. Besides, the in situ-transformed LiCoMnO4 shell can also improve the structural stability of the Li-rich layered oxides by reducing the side reactions and protecting the material from being corroded by the electrolyte. This study provides a strategy for surface modification, which can effectively improve the electrochemical performance of Li-rich layered cathode materials with high performance.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c01955.SEM image of the precursor Ni1/6Co1/6Mn4/6CO3 and the corresponding mapping spectrum; ex situ XRD spectra of the LLO and LSS-0.05 samples; EDS line scan of the selected area and the corresponding HTEM diagram of the LSS-0.05 sample; CV and dQ/dV curves of the first three cycles of the LLO, LSS-0.05, and LSS-0.1 samples; initial charge and discharge curves of LiCoMnO4, LSS-0.2, and LSS-0.4 samples; discharge curves of LLO, LSS-0.05, and LSS-0.1 samples at different rates and with different cycles; typical single titration curve of GITT measurements; equivalent circuit of half-cells; and EIS spectra of LLO, LSS-0.05, and LSS-0.1 samples in the initial cycle (PDF)This article has not yet been cited by other publications.

Artificial Post‐Cycled Structure Modulation Towards Highly Stable Li‐Rich Layered Cathode

Revealing Lithium Configuration in Aged Layered Oxides for Effective Regeneration

Single-crystal Li-rich Layered Cathodes with Suppressed Voltage Decay by Double-Layer Interface Engineering

Lattice and Local Electronic Structure Modulation Enables Ultra-Long-Life Li-Rich Cathode Materials

Structural self-reconstruction strategy empowering Ni-rich layered cathodes with low-strain for superior cyclabilities

Suppressing Bulk Strain and Surface O2 Release in Li-Rich Cathodes by Just Tuning the Li Content

Lattice Oxygen Redox Reversibility Modulation in Enhancing the Cycling Stability of Li‐Rich Cathode Materials

Improving the Electrochemical Performance of a Lithium-Rich Layered Cathode with an In Situ Transformed Layered@Spinel@Spinel Heterostructure

Optimizing Both Bulk and Surface Structure of Li‐Rich Layered Cathodes for Long‐Life and Safe Li‐Ion Batteries

Regulation of 3d‐Transition Metal Interlayered Disorder by Appropriate Lithium Depletion for Li‐Rich Layered Oxide with Remarkably Enhanced Initial Coulombic Efficiency and Stability

Manipulating the Local Electronic Structure in Li‐Rich Layered Cathode Towards Superior Electrochemical Performance

Enabling Long‐Term Cycling Stability Within Layered Li‐Rich Cathode Materials by O2/O3‐Type Biphasic Design Strategy

Facilitating structural stability of the Li-rich layered cathode materials by cation rearrangements and Li vacancies

In Situ Induced Lattice‐Matched Interfacial Oxygen‐Passivation‐Layer Endowing Li‐Rich and Mn‐Based Cathodes with Ultralong Life

Lattice Engineering toward Extraordinary Structural Stability of High‐Performance Single‐Crystal Li‐Rich Layered Oxides Cathodes

Highly stable surface and structural origin for lithium-rich layered oxide cathode materials

Enhancement on the Cycling Stability of the Layered Ni-Rich Oxide Cathode by In-Situ Fabricating Nano-Thickness Cation-Mixing Layers

In-situ surface chemical and structural self-reconstruction strategy enables high performance of Li-rich cathode

Imitating Architectural Mortise‐Tenon Structure for Stable Ni‐Rich Layered Cathodes

In-Situ Constructed Protective Bilayer Enabling Stable Cycling of LiCoO 2 Cathode at High-Voltage

<i>In</i><i>-situ</i> constructed protective bilayer enabling stable cycling of LiCoO<sub>2</sub> cathode at high-voltage