Abstract:al. report an f -TEG featuring a mushroom-like structure that achieves high output power density on human skin without external heat sink via thermal design. The work provides an example of the design process of f -TEGs and paves the pathway toward scalable fabrication of low-cost and high-performance f -TEGs. SUMMARY Flexible thermoelectric generators ( f -TEGs) are promising solutions to power supply for wearable devices. However, the high fabrication costs and low output power density of conventional f -TEGs limit their applications. Here, we present a bulk-material-based f -TEG featuring multifunctional copper electrodes for heat concentration and dissipation and fabrics for comfort and heat-leakage reduction. When worn on the forehead, our f -TEG’s maximum output power density (based on the device’s area) reaches 48 m W/cm 2 at a wind speed of 2 m/s and an ambient temperature of 15 (cid:1) C. A light-emit-ting diode (LED) powered by our f -TEG headband with 100 pairs of thermoelectric pillars can illuminate a paper for reading in a dark room at 17.5 (cid:1) C without an external heat sink or forced convection at the cold side. This work provides a general design approach for high-performance f -TEGs at a low cost. The device-level perspectives ﬁll the critical knowledge gap between state-of-the-art material innovations and practical thermoelectric applications. In summary, we demonstrate strategies to achieve a higher performance, body-powered f -TEG. We use multifunctional thin copper disks as electrodes, heat concentrators and spreaders, spacers, and ﬂexibility enablers. Copper spacers and fabrics are used to suppress the heat loss between the hot and the cold sides through conduction and convection and provide good wearability and comfort even in sweating conditions. We develop an analytical model that predicts an f -TEG’s en-ergy-harvesting performance and helps determine the optimal geometries of the thermoelectric unit in a given thermal environment. In contrast to most reported f -TEGs using thicker thermoelectric pillars to get a larger temperature difference across the pillars (so a larger thermoelectric voltage), our mushroom-like f -TEG’s performance stands out despite the small thickness of thermoelectric pillars (1.9 mm), reducing weight and cost of thermoelectric materials. In indoor testing, our f -TEG’s maximum output power density (based on the device area) on human skin reaches 16 m W/cm 2 at the ambient temperature of 15 (cid:1) C when there is little wind (v air = 0.2 m/s), and the output power density goes up to 48 m W/cm 2 when the wind speed is increased to 2 m/s. An LED powered by our f -TEG headband with 100 pairs of thermoelectric units can illuminate a paper for reading in a completely dark room at 17.5 (cid:1) C without an external heat sink or forced air convection at the cold side. Our f -TEG headband with 50 pairs of thermoelectric units can generate 1.2 mW power during a jog at the ambient temperature of 25 (cid:1) C (little wind and running at a speed of 2.5 m/s) in outdoor testing. Our device-level perspectives are critical to bridging state-of-the-art material research and practical thermoelectric applications. Although this paper focuses on power generation, such devices can also be used for personalized cooling. We envision our low-cost and high-perfor-mance

Elastic aerogel thermoelectric generator with vertical temperature-difference architecture and compression-induced power enhancement

Vertically Designed High-Performance and Flexible Thermoelectric Generator Based on Optimized PEDOT:PSS/SWCNTs Composite Films

High-performance flexible thermoelectric generators with tunable in-plane and out-of-plane architectures

Initiating a Stretchable, Compressible, and Wearable Thermoelectric Generator by a Spiral Architecture with Ternary Nanocomposites for Efficient Heat Harvesting

Harness High-Temperature Thermal Energy via Elastic Thermoelectric Aerogels

Design and Fabrication of Wearable Thermoelectric Generator Device for Heat Harvesting

Stretchable Thermoelectric Generators Based on Bulk Bi2Te3 and Liquid Metals

3D Printed Gelatin Methacrylate Hydrogel‐Based Wearable Thermoelectric Generators

Structural Design for Wearable Self-Powered Thermoelectric Modules with Efficient Temperature Difference Utilization and High Normalized Maximum Power Density

Flexible micro thermoelectric generators with high power density and light weight

Tellurium-Nanowire-Doped Thermoelectric Hydrogel with High Stretchability and Seebeck Coefficient for Low-Grade Heat Energy Harvesting

Ionic Gelatin-Based Flexible Thermoelectric Generator with Scalability for Human Body Heat Harvesting

Flexible and Foldable Films of SWCNT Thermoelectric Composites and an S-Shape Thermoelectric Generator with a Vertical Temperature Gradient

A Wavy-Structured Highly Stretchable Thermoelectric Generator with Stable Energy Output and Self-Rescuing Capability

High-performance, ﬂexible thermoelectric generator based on bulk materials

Stretchable Thermoelectric Generators Metallized with Liquid Alloy

Recyclable, Healable, and Stretchable High‐Power Thermoelectric Generator

Wearable Thermoelectric Generator with Copper Foam As the Heat Sink for Body Heat Harvesting

A Novel PDMS-Based Flexible Thermoelectric Generator Fabricated by Ag2Se and PEDOT:PSS/Multi-Walled Carbon Nanotubes with High Output Performance Optimized by Embedded Eutectic Gallium–Indium Electrodes

High-Power-Density Wearable Thermoelectric Generators for Human Body Heat Harvesting

High-Performance Wearable Bi2Te3-Based Thermoelectric Generator