Abstract:A n-butanol/diesel spray test system was constructed to conduct common rail bench test and constant volume bomb experiments in present work to investigate the impact of different n-butanol blending ratios on spray characteristics and the spray evolution process. To be specific, the research was carried out under the n-butanol blending ratios ofwith 0, 10%, 20%and 40% respectively to study various n-butanol blending ratio effects and to analyze the variation of the physical and chemical characteristics of the fuel. Then, the fuel spray patterns data at 0.4 ms was carefully collected and analyzed to compar the effect of different n-butanol blending ratios on spray penetration and spray angle. In addition, an-butanol/diesel spray model in engine cylinder was also established, to analyze how spray penetration and SMD of blended fuel varied during spray process, , as well as the impacts of n-butanol blending ratios on evaporation characteristics of blended fuel. Furthermore the various changes in velocity field and number density field in spray processes with different blending ratios have been taken into consideration and discussed for more detailed problems. It can be observed from the research data that: in normal temperature and pressure region,as the n-butanol blending ratio increased,the spray penetration decreased and there was a moderate rise in spray angle during spray process; as blending ratios of n-butanol increased by 40%, the spray penetration slightly reduced by 4.95%while reversely the spray angle climbed by 16.7%. Also when the injection pressure ascended, there was obvious rise both in the spray penetration and spray angle, particularly, if injection pressure rose by 40 MPa , the spray angle increased by 28.43°. During the spray evolution process, the n-butanol blending ratios influenced the spray penetration slightly, while in the very initial step of fuel blending process, the higher the n-butanol blending ratio was, the smaller SMD of blended fuel became. Along with the development of the spray process, however, the ultimate spray penetrations of different blended fuel were basically the same. In the injecting duration period, with the increasing of n-butanol blending ratio, there was a substantial drop in the mass of the fuel injected into the cylinder, and the peak velocity value of the jet dropped distinctly. Moreover, as a result of the fall in the viscosity and surface tension, the volatilization of blended fuel was apparently enhanced and subsequently fuel evaporation mass was increased slightly. The n-butanol blending ratios had quite limited impact on number density of drops but obviously facilitated the spray period, that is, the larger the blend ratio was, the better the spray characteristics would be. Besides this, in the central region of the downstream jet the figure of number density reached the highest.

Sooting transition chemistry for iso-octane/n-butanol counterflow diffusion flames

Experimental and numerical study on sooting transition process in iso-octane counterflow diffusion flames: Diagnostics and combustion chemistry

Experimental and Numerical Investigation on Soot Volume Fractions and Number Densities in Non-Smoking Laminar N-Heptane/n-butanol Coflow Flames

Sooting Limits of Nonpremixed N-Heptane, N-Butanol, and Methyl Butanoate Flames: Experimental Determination and Mechanistic Analysis

Experimental and numerical study of soot volume fraction and number density in laminar co-flow diffusion flames of n-decane/n-butanol blends

Experimental investigation on soot formation characteristics of n-heptane/butanol isomers blends in laminar diffusion flames

Spray behavior of butanol-diesel and numerical simulation of mixture formation with engine

Understanding the Reaction Pathways in Premixed Flames Fueled by Blends of 1,3-Butadiene and N-Butanol

Study of soot formations in co-flow laminar diffusion flames of n-heptane and oxygenated aromatic biofuels from atmospheric condition to 2.3 bar

Effects of diluent gases on sooting transition process in ethylene counterflow diffusion flames

The Evolution of Soot Morphology and Nanostructure in Laminar Diffusion Flame of Surrogate Fuels for Diesel

Experimental study on ignition and combustion characteristics of biodiesel-butanol blends at different injection pressures

Comparative Research on Laminar Flame Propagation for Four C8 Fuels

Experimental Study Of The Effect Of Intake Oxygen Concentration On Engine Combustion Process And Hydrocarbon Emissions With N-Butanol-Diesel Blended Fuel

An experimental multiparameter investigation on the thermochemical structures of benchmark ethylene and propane counterflow diffusion flames and implications to their numerical modeling

Experiment Study on Major and Intermediate Species of Ethanol/N-Heptane Premixed Flames

A comparative study on soot and PAH formation of C10 naphthenic ring-containing species in laminar coflow diffusion flames

Non-premixed Ignition, Laminar Flame Propagation, and Mechanism Reduction of N-Butanol, Iso-Butanol, and Methyl Butanoate

Experimental and chemical kinetic study on the laminar flame characteristics of the blends of n-propanol and isooctane at elevated temperature and pressure

A comprehensive experimental study of low-pressure premixed C3-oxygenated hydrocarbon flames with tunable synchrotron photoionization

Simulation Study on the Combustion and Emissions of a Diesel Engine with Different Oxygenated Blended Fuels