Abstract:A digital deconvolution method with pile-up reconstruction has been proposed for scintillator detectors for high rate photon-counting X-ray imaging applications. The detector signal was modeled as an exponential decay waveform convoluted with the single photon response of the SiPM detector. An impulse signal can be obtained by digital deconvolution (unfolding) with much shorter duration, which was then used for energy estimation followed by a trapezoid filter and pile-up discrimination The whole digital deconvolution algorithm has been synthesized and verified by both SIMULINK simulation and experimental tests. The prototype of the detector and the readout electronics were developed for demonstration, using 3 mm x 3 mm x 10 mm LYSO scintillator coupled with a 3 mm x 3 mm SenSL SiPM. A 14 bit, 100 MSPS ADC was used to sample the analog waveform and the digital filter was implemented in a Xilinx Kintex 7 FPGA. The signal width was shortened from similar to 250 ns to 10 similar to 20 ns and then was shaped into trapezoidal pulse with 100 ns width. The energy was estimated from the trapezoid top for better signal collection and noise rejection. The unfolded pulses were used for pile-up discrimination and to reconstruct two pile-up signals from the overlapped trapezoid outputs. The energy performance of the prototype system was firstly validated by measuring the energy spectrums of Am-241, Co-57, Na-22 and Cs-137 radiation sources. The energy resolutions were measured to be 36.9%, 29.9%, 13.9% and 12.9% respectively at 59.5 keV, 122 keV, 511 keV and 662 keV in FWHM. High rate performance was evaluated by an X-ray generator. The maximum output counting rate was measured to 5.36 Mcps without saturation, comparing with the saturated counting rate of 2.34 Mcps using the original LYSO signals The saturation counting rate using digital deconvolution was estimated to be up to similar to 7 Mcps fitted with the paralyzable dead time model, corresponding to similar to 20 Mcps input count rate.

Building of a 4-channel TTL scaler for counting detector signals

Design of A Programmable Multi Frequency Detector

A Fully Dynamic 4-Channel 13b Simultaneous Sampling Incremental ΔΣ ADC Using Cascoded Floating-Inverter-Amplifier and Code Division Multiplexing Technique

Performance Analysis of Chip Tracking Loop Using TDRC Waveform Pseudo-Number Code

A Novel Integrated Circuit for Semiconductor Radiation Detectors with Sparse Readout

NIM - TTL and TTL - NIM converters for single particle pulse counting experiments

Applications of Triggered Scaler Module for Accelerator Timing

Development of a novel scintillation-trigger detector for the MTV experiment using aluminum-metallized film tapes

Digital Deconvolution Of Scintillation Detector Signals For High Rate Photon-Counting X-Ray Imaging Applications

Cross-Detection and Dual-Side Monitoring Schemes for FPGA-Based High-Accuracy and High-Precision Time-to-Digital Converters

Design of a Programmable Gain Waveform Digitization Instrument for Detector Calibration

A Low-power Synthesizable Time-to-Digital Converter Using Amplification to Overcome Mismatch

Design of an integrated multiple-single-channel analyzer

Single Photon Counting Discrimination Voltage Software

Application of the DRS4 Chip for GHz Waveform Digitizing Circuit

A Versatile 16-Channel Front-End Integrated Circuit for Semiconductor Radiation Detectors

A Highly Linear FPGA-Based TDC and a Low-Power Multichannel Readout ASIC with a Shared SAR ADC for SiPM Detectors

A 19 ps Precision and 170 M Samples/s Time-to-Digital Converter Implemented in FPGA with Online Calibration

Performance comparison between signal digitizers and low-cost digital oscilloscopes: spectroscopic, pulse shape discrimination and timing capabilities for nuclear detectors

Design and Implementation of a Compact Analog Constant Fraction Discriminator for High-Resolution Timing in Gamma-Ray Spectroscopy

A 1.3mW 8-bit Two-step Time-to-Digital Converter