Abstract:BACKGROUND: Many clinical observations have shown that immediate loading is indicated when the stabilization of the bone/implant is optimal and when the estimated loads are not excessively high. Nonetheless, more experimental studies are needed to consider the immediate loading protocol as a safe procedure. Mechanical analysis using the finite element (FE) method analysis has been employed by many authors to understand the biomechanical behavior around dental implants.PURPOSE: This study was to evaluate the effect of the diameter and length on the stress and strain distribution of the crestal bone around implants under immediate loading.MATERIALS AND METHODS: By an ad hoc automatic mesh generator, high-quality FE models of complete range mandible was constructed from computer tomography, with three Straumann (Straumann Institute, Waldenburg, Switzerland) implants of various sizes embedded in the anterior zone. The implant diameter ranged from 3.3 to 4.8 mm, and length ranged from 6 to 14 mm, resulting in seven designs. The implant-bone interface was simulated by nonlinear frictional contact algorithm. For each design, vertical and oblique loadings of 150 N were applied, respectively, to each implant, and stresses and strains in the surrounding cortical bone were evaluated.RESULTS: The biomechanics analysis provided results that the oblique loading would induce significantly higher interfacial stresses and strains than the vertical loading, while the intergroup stress difference significant levels was evaluated using t-tests method and the level of significance (.05) that was accepted for significance. Under both loadings, the maximal values were recorded in the 3.3 (diameter) x 10 (length) mm implant configuration, whose mean and peak values were both higher than that of others with significant statistical differences. The second maximal one is 4.1 x 6 mm configuration, and the minimal stresses were recorded in 4.8 x 10 mm configuration, whose strains were also near to lowest.CONCLUSIONS: Increasing the diameter and length of the implant decreased the stress and strain on the alveolar crest, and the stress and strain values notably increased under buccolingual loading as compared with vertical loading, but diameter had a more significant effect than length to relieve the crestal stress and strain concentration.

Differences in the biomechanical behaviors of natural teeth and dental implants

Three dimensional finite element analysis of biomechanical distribution of dental implants with immediate load and delayed load

Assessment of stress shielding around a dental implant for variation of implant stiffness and parafunctional loading using finite element analysis

Three-dimensional finite element analysis of the biomechanical behaviour of different dental implants under immediate loading during three masticatory cycles

Biomechanical evaluation of customized root implants in alveolar bone: a comparative study with traditional implants and natural teeth.

Biomechanical comparison of biomimetically and electrochemically deposited hydroxyapatite-coated porous titanium implants.

Assessing the implant/bone interface by using natural frequency analysis

Effect of different biocompatible implant materials on the mechanical stability of dental implants under excessive oblique load

Measurement of bone damage caused by quasi-static compressive loading-unloading to explore dental implants stability: Simultaneous use of in-vitro tests, μ-CT images, and digital volume correlation

Effect of Diameter and Length on Stress Distribution of the Alveolar Crest around Immediate Loading Implants

Biomechanical Fatigue Behavior of a Dental Implant Due to Chewing Forces: A Finite Element Analysis

Effects of material and coefficient of friction on taper joint dental implants

Influence of Different Abutment Designs on the Biomechanical Behavior of Dental Root-Analog Implant: A Three-Dimensional Finite Element Analysis

Mechano-adaptive Responses of Alveolar Bone to Implant Hyper-loading in a pre-clinical in vivo model

Predicting the holistic force-displacement relation of the periodontal ligament: in-vitro experiments and finite element analysis

Comparison of Dynamic Mechanical Properties of Dentin Between Deciduous and Permanent Teeth

Numerical simulation on the biomechanical interactions of tooth/implant-supported system under various occlusal forces with rigid/non-rigid connections

Investigation of the Effect of Abutment Angle Tolerance on the Stress Created in the Fixture and Screw in Dental Implants Using Finite Element Analysis

Dynamic analyses of a soft tissue–implant interface: Biological responses to immediate versus delayed dental implants

Effect of Short Dental Implant Material on Bone Stress: An In Vitro Finite Element Analysis

Comparative Analysis of Stress and Deformation between One-Fenced and Three-Fenced Dental Implants Using Finite Element Analysis