Abstract:In many applications, viscoelastic properties of reinforced composites need to be determined prior to their real service life. Such properties can be assured by destructive and non-destructive tests. In this paper, a novel non-destructive test (NDT) method based on flexural free vibration is introduced to investigate the viscoelastic properties of fiber-reinforced composites. Three different types of industrial fibers (carbon, glass, and hemp) and an unsaturated polyester resin were selected to produce bar-shaped composites via pultrusion technique. These composite bars were used in a simple NDT method which just required a wooden hammer, two elastic jaws, a microphone and a recorder software program to perform the experiment. The composite bars were mounted on elastic jaws and hit by a wooden hammer at one end of the specimen as a perpendicular impulse. The produced sound at the other side of the bars was recorded. By analyzing the recorded sounds by means of fast Fourier transform (FFT), viscoelastic properties such as flexural elastic modulus and the loss parameter (Tan {\delta}) were calculated for the fiber-reinforced composites. For determination of flexural elastic modulus, the first three modes of vibration in FFT graphs were analyzed using Temuschenco theory. Also, Tan {\delta} was determined by analyzing the drop in the intensity of vibrational energy as a function of time. Although there was a slight discrepancy between the calculated values from the NDT method and the actual data from dynamic mechanical thermal analysis (DMTA) approach, a good agreement was achieved between NDT and DMTA results.

What problem does this paper attempt to address?

The problem that this paper attempts to solve is how to evaluate the viscoelastic properties of fiber - reinforced polymer composites in the bending direction, especially the flexural modulus of elasticity and the loss factor (Tan δ), through a new non - destructive testing (NDT) method. Specifically, the paper aims to: 1. **Introduce a non - destructive testing method based on free - bending vibration**: This method can be used to evaluate the viscoelastic properties of polyester composites reinforced with carbon fiber, glass fiber, and flax fiber in the bending direction. Traditionally, these properties are usually determined by destructive tests such as dynamic mechanical thermal analysis (DMTA), but these methods will cause irreversible damage to the samples. 2. **Verify the effectiveness and accuracy of the new method**: By comparing the results obtained by the NDT method based on free - bending vibration with the traditional DMTA method, the reliability and accuracy of the new method are verified. Although there are some differences between the two methods, the overall trend is consistent, indicating that the new method is feasible. 3. **Explore the differences between different testing methods and their reasons**: The paper analyzes in detail why the modulus of elasticity obtained by the NDT method is about 23% higher than that obtained by the DMTA method, and why there are significant differences in the loss factor (Tan δ) between the two methods. These differences are mainly attributed to different theoretical assumptions, the influence of experimental conditions, and the viscoelastic behavior of materials. ### Main research content - **Sample preparation**: Three different types of fiber - reinforced composites (carbon fiber, glass fiber, and flax fiber) were prepared using the pultrusion molding technique. - **Destructive testing (DMTA)**: The composites were tested using a three - point bending DMTA model, and the changes in their viscoelastic properties with temperature were recorded. - **Non - destructive testing (NDT)**: An NDT method based on free - bending vibration was designed. The vibration sound of the sample was recorded by simple devices (wooden hammer, elastic clamp, microphone, and recording software), and the elastic modulus and loss factor (Tan δ) were calculated by analyzing the sound signal through fast Fourier transform (FFT). ### Results and discussion - **Elastic modulus**: The elastic modulus obtained by the NDT method is about 23% higher than that obtained by the DMTA method. This difference may be due to the different sample preparations during the testing process and the viscoelastic behavior of the materials. - **Loss factor (Tan δ)**: The loss factor obtained by the NDT method is significantly different from that obtained by the DMTA method. Especially in carbon fiber - and glass fiber - reinforced composites, the loss factor obtained by the DMTA method is significantly higher. This may be due to the stress concentration and increased energy dissipation caused by the mechanical treatment of the sample before the DMTA test. ### Conclusion The paper successfully introduced and verified a non - destructive testing method based on free - bending vibration for evaluating the viscoelastic properties of fiber - reinforced polymer composites. Although there are some differences from the traditional DMTA method, the overall trend is consistent, indicating that this method has high reliability and practicality. Future research will further optimize this method and explore other non - destructive testing applications.

Flexural free vibration as a non-destructive test for evaluation of viscoelastic properties of polymeric composites in bending direction

A comparative study on viscoelastic properties of polymeric composites measured by a longitudinal free vibration non-destructive test and dynamic mechanical thermal analysis

Non-Destructive Acoustic Test (NDAT) to Determine Elastic Modulus of Polymeric Composites

Features of Laser-Vibrometric Nondestructive Testing of Polymer Composite Materials Using Air-Coupled Ultrasonic Transducers

Measurement of the Flexural Modulus of Chopped Carbon Fiber Tape Reinforced Thermoplastic with Short Beams

Nondestructive testing and evaluation techniques of defects in fiber-reinforced polymer composites: A review

Characterization of the flexural behavior of a reactive graphitic nanofibers reinforced epoxy using a non-linear damage model

Ultrasonic and vibration methods for the characterization of pultruded composites

Nondestructive testing of composite T-Joints by TNDT and other methods

Investigating the flexural behavior of nanomodified multi-delaminated composites using acoustic emission technique

Strain Measurement for Composite Materials During Mechanical Testing Based on Fiber Bragg Grating Monitoring

Specific Features of Nondestructive Testing of Polymer and Composite Materials Using Air-Coupled Ultrasonic Excitation and Laser Vibrometry

Accelerated estimation of the very high cycle fatigue strength and life of polymer composites under ultrasonic cyclic three-point bending

Flexural progressive damage and failure behavior of carbon-aramid/epoxy hybrid woven composites

Nondestructive evaluation of carbon-fiber composites using digital image correlation, acoustic emission, and optical based modal analysis

Virtual Tests of Elastodynamic Response of Natural Fiber-Reinforced Orthotropic Plates

Acoustic Emission-Based Analysis of Damage Mechanisms in Filament Wound Fiber Reinforced Composite Tubes

Damage Detection Of Composite Laminates Based On Vibration Testing

Damage Sensing in Natural Fiber/Epoxy Composites

In Situ Non-Destructive Stiffness Assessment of Fiber Reinforced Composite Plates Using Ultrasonic Guided Waves