Abstract:In order to improve the wear and corrosion resistance of Ti-6Al-4V, a novel beta-Ta2O5 nanoceramic coating was synthesised using reactive sputter deposition enabled by double glow discharge plasma technique. The surface topography, chemical composition, and microstructure of the newly developed coating were characterised by a variety of surface analytical techniques. The coating microstructure was found to exhibit a compact striated pattern extending in a direction perpendicular to coating surface, which is composed of equiaxed beta-Ta2O5 grains with an average grain size of similar to 20 nm, well adhered to the Ti-6A1-4V substrate. The hardness and the Young's modulus of the as-deposited coating were obtained by nanoindentation, and the adhesion strength between the coating and substrate was determined by a scratch tester. The dry sliding wear behaviours of the coating were investigated at room temperature against Si3N4 ceramic balls at room temperature under applied loads ranging from 2.3 N to 5.3 N using a ball-on-disc tribometer. The specific wear rates of the coating exhibited only a slight increase with applied normal load, and were shown to be two orders of magnitude lower than that for Ti-6Al-4V under the same loading condition. Furthermore, the electrochemical behaviour of the coating immersed in 3.5 wt.% NaCl solution was systematically examined by using a range of complementary electrochemical techniques including potentiodynamic polarisation, electrochemical impedance spectroscopy (EIS), MottSchottky analysis as well as potential of zero charge (PZC). The results showed that the corrosion resistance of the beta-Ta2O5 nanoceramic coating was better than that of Ti-6Al-4V alloy in 3.5 wt.% NaCl solution. Hence, by possessing higher mechanical properties and good wear and corrosion resistance, the beta-Ta2O5 nanoceramic coating is considered to be a promising candidate for protection of engineering components operating under harsh conditions. (C) 2016 Elsevier B.V. All rights reserved.

Preparation, anticorrosion mechanism, and application of nano-Ti polymer-containing coating

Research on Nano-Titanium Modified Phenolic Resin Coating and Corrosion Resistance

Research on nano-Ti modified polymer by high energy milling

Vinyl Chloride-Co-Vinyl Isobutyl Ether Resin Coating Modified by Nano-TiO 2 Paste

TiO 2 Nanocontainers Coconstructed Using Polymers and Corrosion Inhibitors for Anticorrosion Reinforcement of Waterborne Epoxy Coatings

Nano-Composite Coatings with Improved Mechanical Properties and Corrosion Resistance by Thermal Spraying

Preparation and Properties of Nano-TiO2 Dispersion/Epoxy Coatings

Polydimethylsiloxane-titania nanocomposite coating: Fabrication and corrosion resistance

Functionalized Ti3c2tx-Based Nanocomposite Coatings for Anticorrosion and Antifouling Applications

Formation and Characterization of Water-repellent Nano TiO2 Coating and Studying its Anticorrosion Property

Nanostructured Superhydrophobic Titanium-Based Materials: A Novel Preparation Pathway to Attain Superhydrophobicity on TC4 Alloy

Preparation and Corrosion Resistance of AKT-Waterborne Polyurethane Coating

Corrosion and Wear Behaviours of a Reactive-Sputter-deposited Ta2O5 Nanoceramic Coating

Effects of TiO2 Nanoparticles on the Overall Performance and Corrosion Protection Ability of Neat Epoxy and PDMS Modified Epoxy Coating Systems

Impact Mechanism of Nano-Sized TiO2 and SiO2 on Corrosion Resistance of Electric Arc Spraying Sealing Coat

A Facile Nano-Tio2 Coating Effectively Enhancing the Microscopic Properties of Metal-Polymer Interface

Preparation and Protective Effects of Nano-Tio2 Composite Coatings on LY12 Aluminum Alloys

Preparation and characterization of TiO2/ZnO composite coating on carbon steel surface and its anticorrosive behavior in seawater

Preparation and Characterization of the Polymer-Metal Titanium Nanometer Flake

Modification of nano-hybrid silicon acrylic resin with anticorrosion and hydrophobic properties

STUDY ON A HYDROPHOBIC NANO-TIO2 COATING AND ITS PROPERTIES FOR CORROSION PROTECTION OF METALS