Abstract:A novel micro/nanoscale rough structured superhydrophilic hybrid-coated mesh that shows underwater superoleophobic behavior is fabricated by spray casting or dipping nanoparticle–polymer suspensions on stainless steel mesh substrates. Water droplets can spread over the mesh completely; meanwhile, oil droplets can roll off the mesh at low tilt angles without any penetration. Besides overcoming the oil-fouling problem of many superhydrophilic coatings, this superhydrophilic and underwater superoleophobic mesh can be used to separate oil and water. The simple method used here to prepare the organic–inorganic hybrid coatings successfully produced controllable micro-nano binary roughness and also achieved a rough topography of micro-nano binary structure by controlling the content of inorganic particles. The mechanism of oil–water separation by the superhydrophilic and superoleophobic membrane is rationalized by considering capillary mechanics. Tetraethyl orathosilicate (TEOS) as a base was used to prepare the nano-SiO2 solution as a nano-dopant through a sol-gel process, while polyvinyl alcohol (PVA) was used as the film binder and glutaraldehyde as the cross-linking agent; the mixture was dip-coated on the surface of 300-mesh stainless steel mesh to form superhydrophilic and underwater superoleophobic film. Properties of nano-SiO2 represented by infrared spectroscopy and surface topography of the film observed under scanning electron microscope (SEM) indicated that the film surface had a coarse micro–nano binary structure; the effect of nano-SiO2 doping amount on the film’s surface topography and the effect of such surface topography on hydrophilicity of the film were studied; contact angle of water on such surface was tested as 0° by the surface contact angle tester and spread quickly; the underwater contact angle to oil was 158°, showing superhydrophilic and underwater superoleophobic properties. The effect of the dosing amount of cross-linking agent to the waterproof swelling property and the permeate flux of the film were studied; the oil–water separation effect of the film to oil–water suspension and oil–water emulsion was studied too, and in both cases the separation efficiency reached 99%, which finally reduced the oil content to be lower than 50 mg/L. The effect of filtration times to permeate flux was studied, and it was found that the more hydrophilic the film was, the stronger the stain resistance would be, and the permeate flux would gradually decrease along with the increase of filtration times.

The optimized microbial-induced calcium carbonate precipitation process to fabricate underwater superoleophobic mesh for efficient oil-water separation

Fabrication of a Novel Superhydrophobic and Superoleophilic Surface by One-Step Electrodeposition Method for Continuous Oil/water Separation

Superhydrophilic and underwater superoleophobic cement-coated mesh for oil/water separation by gravity

Robust superhydrophilic and underwater superoleophobic membrane optimized by Cu doping modified metal-organic frameworks for oil-water separation and water purification

Bio-inspired Fabrication of Superhydrophilic and Underwater Superoleophobic Mineralized Polypropylene Nonwoven Meshes for Oil/Water Separation

Micro/Nanoscale Structured Superhydrophilic and Underwater Superoleophobic Hybrid-Coated Mesh for High-Efficiency Oil/Water Separation

Fabrication of a superhydrophilic/underwater superoleophobic stainless steel mesh for oil/water separation with ultrahigh flux

Cubic MOF coated stainless steel mesh with underwater superoleophobicity for highly efficient oil/water separation

Mineral-Coated Polymer Membranes with Superhydrophilicity and Underwater Superoleophobicity for Effective Oil/Water Separation

High Flux Durability Underwater Superoleophobic Mesh Modified by Poly (maleic Acid Mono-(2-(dimethylamino)-ethyl Ester-Co-hydroxyethyl Acrylate) and Nanosilica Particles Hybrid

One-step in-situ fabrication of carbon nanotube/stainless steel mesh membrane with excellent anti-fouling properties for effective gravity-driven filtration of oil-in-water emulsions

A rapid two-step process to prepare a high-throughput, efficient, reusable superhydrophobic–superoleophilic stainless steel mesh for oil/water separation

Recyclable superhydrophilic meshes with scalable and robust coating for separating oily wastewater

Development of superhydrophilic Al foil with micropore arrays via mask electrochemical machining and chemical immersion for efficient oil/water separation

Surface Chemistry-Dominated Underwater Superoleophobic Mesh with Mussel-Inspired Zwitterionic Coatings for Oil/water Separation and Self-Cleaning

Facile preparation and modification of robust BiOCl/Bi 2 O 3 coated mesh with superwetting and anti-biofouling performance for oil/water separation and wastewater treatment

Robust Photopolymerized Superoleophobic/Superhydrophilic Mesh for Oil-Water Separation

Synthesis of Si-Based High-Efficiency and High-Durability Superhydrophilic-Underwater Superoleophobic Membrane of Oil–Water Separation

A self-cleaning TiO2 coated mesh with robust underwater superoleophobicity for oil/water separation in a complex environment

2D Nano-Mica Sheets Assembled Membranes for High-Efficiency Oil/Water Separation

Synergistic effect of nano-silica and eco-friendly hydrogel for the cost-effective and highly efficient oil-water separation