Abstract:SnO2 has the advantages of excellent photostability and can be prepared at low-temperature below 200 degrees C.It is regarded as one of the excellent materials for the electron transport layer, and widely used in efficient andstable planar heterojunction perovskite solar cells. In this work, the low-cost, dense and uniform SnO2 electrontransport layer is prepared by spin coating at low temperature (150 degrees C) for perovskite solar cells with astructure of FTO/SnO2/CH3NH3PbI3 (MAPbI3)/Spiro-OMeTAD/Au. The crystallization and photoelectricproperties of SnO2 electron transport layers prepared at different concentrations (2.5%-10%) at 150 degrees C, and theinfluences of SnO2 electron transport layers on the formation of perovskite films and the performances ofperovskite solar cells are discussed. By analyzing the scanning electron microscope (SEM), ultraviolet-visiblelight absorption spectrum (UV-Vis) and transmission spectrum of the SnO2 film, it is found that the coverageand light transmittance of the substrate and band gap of the SnO2 film increase as the SnO2 content increases,while the absorbance decreases. By analyzing the SEM, UV-Vis, X-ray diffraction (XRD) and steady-statephotoluminescence spectrum (PL) analysis of the SnO2/MAPbI3 thin film, it is found that the MAPbI3deposited on the SnO2 layer with a concentration of 7.5% is uniform and pinhole-free, has the largest particlesize and the best crystallinity, as well as more effective charge extraction capability and transport capability.By analyzing the electrochemical impedance (EIS) and external quantum efficiency (EQE) of the device, theSnO2 electron transport layer with a concentration of 7.5% has better interface contact and lower interfaceresistance, which is beneficial to reducing the recombination of carriers and improving the photoelectricconversion capability, The perovskite solar cells based on SnO2 layer prepared with a concentration of 7.5%reaches a photoelectric conversion efficiency of 15.82% (Voc = 1.06 V, Jsc = 21.62 mA/cm2, FF = 69.40%), Afterstoring for 600 h in ambient air ((25 +/- 5) degrees C, RH>70%) without encapsulation, its efficiency remains 92% of theinitial efficiency. At the same time, we prepare flexible devices on flexible substrates (TIO/PEN) by using SnO2precursor with a concentration of 7.5%, which exhibits good photovoltaic performance and achieves aphotoelectric conversion efficiency of 13.12%, and storage time for 84 d in ambient air ((30 +/- 5) degrees C, RH>70%)without encapsulation, its efficiency remains 48% of the initial efficiency. The PCE retains 78% of the initialefficiency after 1000 bending cycles with a bending radius of 3 mm. The study of optimizing the concentrationof SnO2 has laid a foundation for improving the performance of flexible perovskite solar cells.

Chemical bath deposition of mesoporous SnO2 to improve interface adhesion and device operational stability

Low-temperature preparation of SnO2 electron transportlayer for perovskite solar cells

Multifunctional Regulation of Chemical Bath Deposition Based SnO2 for Efficient Perovskite Solar Cells.

Modification of SnO2 by Acidic FAAc-HI Solution for Efficient and Stable Perovskite Solar Cells with a Multifunctional Interface

Low-temperature Preparation of SnO<sub>2</sub> Electron Transport Layer for Perovskite Solar Cells

Optimized SnO2 preparation and coherent interlayers for enhanced charge dynamics and efficient perovskite photovoltaics

Superior SnO2 Electron Transport Layer Via Bifunctional Interfacial Regulation Using Cesium Sulfate for Efficient Perovskite Solar Cell

Bifunctional SnO 2 Colloid Offers No Annealing Effect Compact Layer and Mesoporous Scaffold for Efficient Perovskite Solar Cells

Polyelectrolyte-Doped SnO<sub>2</sub> as a Tunable Electron Transport Layer for High-Efficiency and Stable Perovskite Solar Cells

Vacuum Thermal-Evaporated SnO2 As Uniform Electron Transport Layer and Novel Management of Perovskite Intermediates for Efficient and Stable Planar Perovskite Solar Cells

Aromatic carboxyl acid regulated nanoparticle deposition and passivation of tin oxide for high performance perovskite solar cells

Multifunctional Compound‐Regulated SnO2 for High‐Efficiency and Stable Perovskite Solar Cells under Ambient Air

SnO2 modified mesoporous ZrO2 as efficient electron-transport layer for carbon-electrode based, low-temperature mesoscopic perovskite solar cells

Electrochemical Reduction and Ion Injection of Annealing‐Free SnO2 for High Performance Perovskite Solar Cells

Ultralow‐temperatureSnO2 Electron Transport Layers Fabricated by Intermediate‐controlled Chemical Bath Deposition for Highly Efficient Perovskite Solar Cells

Organic molecule and inorganic salt synergistic modified SnO2 for efficient perovskite solar cells

Periodic Acid Modification of Chemical‐Bath Deposited SnO2 Electron Transport Layers for Perovskite Solar Cells and Mini Modules

Non-toxic and rapid chemical bath deposition for SnO2 electron transporting layers in perovskite solar cells

Modification of SnO2 Buried Interface with Thiourea to Enhance the Performance of Perovskite Solar Cells

Low-temperature Preparation of Tin Dioxide Electron Transport Layer in Perovskite Solar Cells

Modification Engineering in SnO 2 Electron Transport Layer toward Perovskite Solar Cells: Efficiency and Stability