Abstract:A digital deconvolution method with pile-up reconstruction has been proposed for scintillator detectors for high rate photon-counting X-ray imaging applications. The detector signal was modeled as an exponential decay waveform convoluted with the single photon response of the SiPM detector. An impulse signal can be obtained by digital deconvolution (unfolding) with much shorter duration, which was then used for energy estimation followed by a trapezoid filter and pile-up discrimination The whole digital deconvolution algorithm has been synthesized and verified by both SIMULINK simulation and experimental tests. The prototype of the detector and the readout electronics were developed for demonstration, using 3 mm x 3 mm x 10 mm LYSO scintillator coupled with a 3 mm x 3 mm SenSL SiPM. A 14 bit, 100 MSPS ADC was used to sample the analog waveform and the digital filter was implemented in a Xilinx Kintex 7 FPGA. The signal width was shortened from similar to 250 ns to 10 similar to 20 ns and then was shaped into trapezoidal pulse with 100 ns width. The energy was estimated from the trapezoid top for better signal collection and noise rejection. The unfolded pulses were used for pile-up discrimination and to reconstruct two pile-up signals from the overlapped trapezoid outputs. The energy performance of the prototype system was firstly validated by measuring the energy spectrums of Am-241, Co-57, Na-22 and Cs-137 radiation sources. The energy resolutions were measured to be 36.9%, 29.9%, 13.9% and 12.9% respectively at 59.5 keV, 122 keV, 511 keV and 662 keV in FWHM. High rate performance was evaluated by an X-ray generator. The maximum output counting rate was measured to 5.36 Mcps without saturation, comparing with the saturated counting rate of 2.34 Mcps using the original LYSO signals The saturation counting rate using digital deconvolution was estimated to be up to similar to 7 Mcps fitted with the paralyzable dead time model, corresponding to similar to 20 Mcps input count rate.

Waveform Digitizing for LaBr$_3$/NaI Phoswich Detector

Waveform Digitizing for LaBr_3/NaI Phoswich Detector

A Large Area LaBr3/NaI Phoswich for Hard X-ray Astronomy

Design Of A High Resolution Phoswich Pet Detector

A Phoswich Composed Of Csi:Na And Labr3:Ce To Improve The Low Energy Response Of Labr3:Ce

Design of a Portable Phoswich Detector for Simultaneous Α, Β, and Γ Identification

Design of digital pulse shape discriminator for phoswich detector

Crystal Identification Electronics And Algorithm Applied to Phoswich Detectors for PET

Optimal Design of Waveform Digitisers for Both Energy Resolution and Pulse Shape Discrimination

Scintillation detectors constructed with an optimized 2x2 silicon photomultiplier array

Three-detector Setup for PAL Spectrometer Based on DRS4 Waveform Digitizing Board

A Side-by-side LYSO/GAGG Phoswich Detector Aiming for SPECT Imaging

Digital Deconvolution Of Scintillation Detector Signals For High Rate Photon-Counting X-Ray Imaging Applications

Performance of Linear PSD Methods on Α/γ Discrimination for LaBr3 : Ce Scintillation Detectors with Different Sampling Properties

Performance of Linear Classification Algorithms on Α/γ Discrimination for LaBr3:Ce Scintillation Detectors with Various Pulse Digitizer Properties

Waveform Simulation for Scintillation Characteristics of NaI(Tl) Crystal

Development of a Phoswich Detector System for Radioxenon Monitoring

n/? discrimination of SiPM array-based CLYC detector

Logistic regression-time–frequency algorithm for α/β discrimination in silicon photomultiplier–based Phoswich detectors

1064-Μm-band Up-Conversion Single-Photon Detector

Pulse shape discrimination in an organic scintillation phoswich detector using machine learning techniques