Abstract:Using discrete element method (DEM) modeling and near-infrared (NIR) spectroscopy, the feasibility of powder mixing in the initial pre-melting zones of a twin screw extruder using two independent feeders was studied. Previous work in the pharmaceutical and food industry has focused on mixing when materials are melted or on material homogeneity at the extruder's output. Depending on the formulation, ensuring a fully blended formulation prior to melting may be desired. Experiments were conducted using a Coperion ZSK-18 extruder to evaluate if blend uniformity can be achieved by exploring screw configuration, screw speed, and powder feed rate. As powder exited the extruder and deposited on a conveyor belt, an in-line NIR spectrophotometer measured spectra of material. Chemometric-based models predicted unknown concentrations to evaluate if blend uniformity was achieved. Using the EDEM software, Hertz-Mindlin contact model, and dimensions of the extruder, DEM simulations complemented the experimental work. The DEM computational models provided understanding of mixing patterns inside the extruder at particle scale and helped select the screw configuration before doing experimentation. The simulations showed good axial mixing for all the screw configurations studied, while good cross (radial) mixing was only observed for the screw configuration with 90-degree kneading elements. Therefore, the screw configuration with two 90-degree kneading elements was chosen for the experimental study. The RTD profiles when using a screw configuration with only conveying screw elements are comparable to a plug flow reactor (PFR), while the profiles when using kneading elements are more comparable to an ideal continuous stirred tank reactor (CSTR). For the screw configuration with 90 degrees kneading elements, the mean residence time (MRT) decreases with an increase in the screw speed. Experimental NIR spectra showed that concentrations can be predicted with an error of 2%. It was demonstrated that the twin screw extruder can provide proper dry powder mixing of two powder feed streams based on a unit dose scale, enabling continuous powder mixing prior to the melting zone in the extruder for the formulation studied with a cohesive API. This setup may also work for other types of formulations. These studies can help in developing lean hot melt as well as wet extrusion/granulation processes using twin screw extruders for the continuous manufacturing of oral solid dosage products.

The role of the kneading paddle and the effects of screw revolution speed and water content on the preparation of solid dispersions using a twin-screw extruder

Evolution of residence time distribution and fill degree in co-rotating twin-screw extruder

Hydrodynamics and Film Formation Characteristics in a Horizontal Self‐cleaning Twin‐shaft Kneader for Polymer Devolatilization

Numerical Simulation of Hydrodynamics and Mixing Characteristics of High-Viscosity Non-Newtonian Fluid in Twin-Shaft Kneaders

Novel Hot Melt Extruded Matrices of Hydroxypropyl Cellulose and Amorphous Felodipine–Plasticized Hydroxypropyl Methylcellulose As Controlled Release Systems

Effects of pitched tips of novel kneading disks on melt mixing in twin-screw extrusion

Melt-Mixing by Novel Pitched-Tip Kneading Disks in a Co-Rotating Twin-Screw Extruder

Molecular Mechanisms Involved in Supersaturation of Emodin Ternary Solid Dispersions Based on Bonding Agents.

Dry Powder Mixing Is Feasible in Continuous Twin Screw Extruder: Towards Lean Extrusion Process for Oral Solid Dosage Manufacturing

Understanding the mechanism for sodium tripolyphosphate in improving the physicochemical properties of low-moisture extrusion textured protein from rapeseed protein and soybean protein blends

Numerical Simulation and Experimental Validation of Mixing Performance of Kneading Discs in A Twin Screw Extruder

Preparation of Hot-Melt-Extruded Solid Dispersion Based on Pre-Formulation Strategies and Its Enhanced Therapeutic Efficacy

The Effect of Cooling on the Degree of Crystallinity, Solid-State Properties, and Dissolution Rate of Multi-Component Hot-Melt Extruded Solid Dispersions

Role of rheology in formulation and process design of hot melt extruded amorphous solid dispersions

Modelling drug degradation of amorphous solid dispersion during twin-screw extrusion

Hot Melt Extrusion Technology for Improved Dissolution, Solubility and "Spring-Parachute" Processes of Amorphous Self-Micellizing Solid Dispersions Containing BCS II Drugs Indomethacin and Fenofibrate: Profiles and Mechanisms.

A Miniaturized Extruder to Prototype Amorphous Solid Dispersions: Selection of Plasticizers for Hot Melt Extrusion

Dispersive Mixing Performance Evaluation of Special Rotor Segments in an Intermeshing Co-Rotating Twin-Screw Extruder by Using Weighted Probability Distributions

Impact of non-binder ingredients and molecular weight of polymer binders on heat assisted twin screw dry granulation

Recent studies on the processes and formulation impacts in the development of solid dispersions by hot-melt extrusion

The preparation, characterization, and application of porous core–shell composite particles produced with laboratory-scale spray dryer