An Improved Multi-Pulse Rectifier Circuit for Input Current Harmonic Suppression Using Passive Devices

Muhammad Ahmad Khurshid,Tahir Mahmood,Abdul Wahab

Abstract:Circuit

Engineering,Physics

What problem does this paper attempt to address?

An Effective Method to Suppress Resonance in Input LC Filter of a PWM Current-Source Rectifier

Y. W. Li,B. Wu,N. Zargari,J. Wiseman,D. Xu

DOI: https://doi.org/10.1109/ipemc.2006.4778161

2006-01-01

Abstract:The PWM current-source rectifier (CSR) is becoming a preferred choice to provide a DC current source for DC loads or current source fed drives. However the control of the resonance of the input LC filter is one of the main challenges. To dampen the LC resonance with minimum control and implementation efforts, a two-step Posicast controller for modulation signal shaping is first examined, which can be easily inserted into the existing CSR control loop. The parameters of the two-step Posicast controller are fixed by the lightly damped plant, which makes it unsuitable at high power levels due to the inaccurate compensation associated with the low switching frequency. A three-step compensator is then designed in this work. By selecting its parameters according to the existing control algorithm, the three-step compensator is very effective for the low switching frequency CSR with precise resonance compensation and easy implementation. Detailed design and analysis are presented. Simulation and experimental results are provided to verify the effectiveness of the proposed damping approach
Passive Harmonic Reduction for 12-Pulse Rectifier Using two Kinds of Unconventional Multi-tap Inter-Phase Reactors

Tianlong Yu,Chen Zhao,Jingfang Wang,Pengying Xiong,Teng Liu

DOI: https://doi.org/10.1109/IPEMC-ECCEAsia60879.2024.10567588

2024-05-17

Abstract:A passive harmonic reduction scheme using two kinds of unconventional multi-tap inter-phase reactors is proposed to reduce the input current harmonics of the 12pulse rectifier effectively, and a novel multi-pulse rectifier with an approximately sinusoidal input current is obtained. The proposed passive harmonic reduction circuit (PHRC) is mounted on the DC side of the rectifier and comprises four auxiliary diodes, a three-tap inter-phase reactor and a four-tap inter-phase reactor. The four auxiliary diodes in the PHRC alternate conduction which increases the number of steps of the input current from 12 to 30 and effectively suppresses the input current harmonics. The proposed scheme does not require the use of any active devices. Thus, the proposed scheme has the advantages of simple circuit structure, cost-effective and high reliability. A 20 kW simulation prototype is built, and the simulation results verify the accuracy and effectiveness of the theoretical analysis.

Engineering,Physics
Current Source PWM Rectifier Based on Indirect Current Control

Lin Ping

DOI: https://doi.org/10.3969/j.issn.1003-8930.2008.03.012

2008-01-01

Abstract:The electronic installation brings harmonic pollution to power system and descend power factor.In order to sovle the problem,mathematical model of 3-phase current-source PWM rectifiers are founded in abc stationary coordinate.The indirect current control strategy is adopted through controlling fundamental and phase of AC-side in 3-phase current-source PWM rectifiers.Computer simulation and experimental results show that unity power factor in network and stable current source in DC-link are obtained based on the control strategy.
Control of PWM Rectifier under Unbalanced Input Voltages

HE Ming-ming,HE Yi-kang,PAN Zai-ping

DOI: https://doi.org/10.3969/j.issn.1003-8930.2007.04.003

2007-01-01

Abstract:Pulse width modulation(PWM) rectifier is the best method for the AC-DC converting.But there exists harmonic power in the power grid under unbalanced voltages which can affect the output quality seriously.Positive and negative sequence separating method was presented to solve the problem,the key of which is to trace the positive and negative current.The current references under positive and negative sequence d-q axis were obtained using the relation of voltage,current and power,through which the control method was improved and simulation model was set up.The result shows that the new method can control the input current,decrease the harmonic power,keep the DC voltage steady and PWM rectifier working without interruption under unbalanced input voltages.
A Multipulse Pattern Modulation Scheme for Harmonic Mitigation in Three-Phase Multimotor Drives

Pooya Davari,Yongheng Yang,Firuz Zare,Frede Blaabjerg

DOI: https://doi.org/10.1109/jestpe.2015.2461018

IF: 5.462

2016-01-01

IEEE Journal of Emerging and Selected Topics in Power Electronics

Abstract:A continuous improvement of power electronics technology has widely increased the applications of adjustable speed motor drives in many areas. Beyond the control flexibility, the power electronics devices (e.g., diode rectifiers) are also the main harmonic source to the grid due to their nonlinearity, which thus deteriorates the power grid quality and also lowers the conversion efficiency. Both degradations are apt to occur in motor drive applications. At present, many industrial drives are equipped with three-phase diode rectifiers and employ passive filtering techniques on the ac or the dc side of the rectifier. In such topologies, it is difficult to implement the priorart harmonic control strategies. Moreover, the total cost and complexity has become the main obstacle for these harmonic elimination approaches in multiple drive systems. Therefore, in this paper, a new cost-effective harmonic mitigation approach has been proposed for multiple drives. The proposed approach can control the generated current harmonics by benefiting of the nonlinearity of the drive units and through a novel current modulation scheme. The obtained results at the simulation and the experimental level validate the effectiveness of the proposed approach.
A Novel Series 24-Pulse Rectifier Operating in Low Harmonic State Based on Auxiliary Passive Injection at DC Side

Xiaoqiang Chen,Tun Bai,Ying Wang,Jiangyun Gong,Xiuqing Mu,Zhanning Chang

DOI: https://doi.org/10.3390/electronics13061160

IF: 2.9

2024-03-22

Electronics

Abstract:To reduce the current harmonics on the input side of a multi-pulse rectifier, this paper proposes a low harmonic current source series multi-pulse rectifier based on an auxiliary passive injection circuit at the DC side. The rectifier only needs to add an auxiliary passive injection circuit on the DC side of the series 12-pulse rectifier, which can change its AC input voltage from 12-step waves to 24-step waves. We analyzed the working mode of the rectifier, optimized the optimal turn ratio of the injection transformer from the perspective of minimizing the total harmonic distortion (THD) value of the input voltage on the AC side, and analyzed the diode open circuit fault in the auxiliary passive injection circuit. Test verification shows that, after using the passive harmonic injection circuit, the THD value of the input voltage of the AC side of the rectifier is reduced from 14.03% to 4.86%. The THD value of the input current is reduced from 5.30% to 2.16%. The input power factor has been increased from 98.86% to 99.83%, and the power quality has been improved.

engineering, electrical & electronic,computer science, information systems,physics, applied
A Harmonic Current Suppression Method for Single-Phase PWM Rectifier Based on Feedback Linearization

Jingzhu Deng,Yeshuang Lei,Ju-Song Kang,Miao Yu

DOI: https://doi.org/10.1109/icopesa54515.2022.9754411

2022-01-01

Abstract:This paper presents a harmonic current suppression method based on feedback linearization for single-phase voltage source pulse width modulation (PWM) rectifier, which can achieve fast dynamic response and low total harmonic distortion (THD). Starting from the state space model of single-phase PWM rectifier, by introducing feedback linearization method and by means of coordinate transformation and state feedback, a precise linearization model is attained and a feedback linearization based current controller is designed. Considering that the instantaneous power of the single-phase rectifier pulsates at twice the grid frequency, which results in a large number of harmonic currents, a notch filter is added in the voltage PI loop to reduce the second harmonic component of the inductor current amplitude reference. In addition, in order to further reduce the current harmonic, a sliding mode controller is designed for the inner loop. Finally, the simulation results prove the effectiveness of the proposed method.
Low harmonic 12-pulse rectifier with a circulating current shaping circuit

Jingfang WANG,Xuliang YAO,Qi GUAN,Changji DENG,Shiyan YANG

DOI: https://doi.org/10.3906/elk-1907-204

2020-05-08

Abstract:This paper proposes a four-star 12-pulse diode rectifier with a circulating current shaping circuit CCSC on the DC side to decrease the input current harmonics effectively. The type of circulating current that can eliminate the input current harmonics is analysed and its waveform parameters are derived. The effects of triangular circulating current on the harmonics of the input current are analysed, and the harmonic suppression mechanism of the triangular circulating current is revealed. This scheme has excellent harmonic suppression capability, and the capacity of CCSC is only 2.35% of output power of the 12-pulse rectifier. Thus, this scheme is cost effective for high power applications. The experimental results confirm the theoretical analysis and near sinusoidal input current is obtained.

computer science, artificial intelligence,engineering, electrical & electronic
Novel passive harmonic suppression method for series-connected multi-pulse rectifiers

Quanhui Li,Lei Gao,Fangang Meng

DOI: https://doi.org/10.1007/s43236-023-00738-5

IF: 0.913

2024-01-06

Journal of Power Electronics

Abstract:To improve the power quality and reliability of series-connected multi-pulse rectifiers (MPR), a passive harmonic suppression method is proposed in this paper. According to the topology of the rectifier, the operation modes are examined, and the operating waveforms are studied based on the operation modes. Based on the operating waveform of the rectifier, the relationship between the input voltage and the turns ratio of the auxiliary single-phase transformer (AST) is obtained, and the optimal turns ratio of the AST is calculated. The obtained results express that the input voltage THD is 4.4%, and that the input current THD is about 2.6%. The magnetic rating of the AST is only 1.72% of the output power. The proposed passive harmonic suppression method has the advantages of low loss and good harmonic suppression capability.

engineering, electrical & electronic
Input Current Step-Tripling for 12-Pulse Rectifier Using a Passive Four-tap Changer

Jingfang Wang,Yusheng Lv,Xuliang Yao,Lei Li,Qiming Chen

DOI: https://doi.org/10.1109/tie.2022.3146545

IF: 7.7

2022-01-01

IEEE Transactions on Industrial Electronics

Abstract:To effectively suppress the input line current harmonics of a 12-pulse rectifier under slightly complex hardware, this article proposed an input line current step-tripling scheme for a 12-pulse rectifier using a novel passive four-tap changer (FTC). The proposed FTC consists of a retrofitted four-tap interphase reactor (RFT-IPR) and four auxiliary diodes. Two auxiliary diodes are connected to the inner taps of the RFT-IPR, but the other two auxiliary diodes are connected to the outer taps of the RFT-IPR. The inner and outer auxiliary diodes modulate and increase the output current states of the rectifier bridges together first; then, the FTC extends the 12-step to 36-step input line current, and the near sinusoidal input current with 3 THD is obtained. The proposed FTC not only has a very low capacity (2.6 of the output power) but also does not require any active switching device aside from four auxiliary diodes; thus, the proposed scheme is a cost-effective, reliable, and efficient solution to harmonics pollution. An experimental prototype with an output power of 2.4 kW is built, and the correctness of the theoretical analysis is verified by the experimental results.

automation & control systems,engineering, electrical & electronic,instruments & instrumentation
A New Auxiliary Pulse Multiplication Scheme for Harmonic Suppression of the 12-Pulse Rectifier

Jingfang Wang,Anchen Chen,Xuliang Yao

DOI: https://doi.org/10.1109/pesgre52268.2022.9715755

2022-01-02

Abstract:To lower the voltage stress of auxiliary diodes and not increase the complexity of IPR, a new auxiliary pulse multiplication scheme for harmonic suppression of the 12-Pulse rectifier is presented in this paper. The proposed auxiliary pulse multiplication circuit (PMC) comprises a single-phase transformer and an auxiliary single-phase rectifier (ASR) connected in the load path. The ASR in PMC produces a square-wave circulating current on the dc-link, aiming at increasing the states of output current and voltage of the three-phase rectifier bridge, then the steps number of the input current of the rectifier is improved to 24-step, and the input current harmonics is validly mitigated. The 24-pulse output voltage is also obtained by using the 12-pulse rectifier in conjunction with ASR. The proposed PMC scheme is affordable and easy implementation because only a small-capacity PMC (only 2% of output power) is sufficient to double the pulse number. An experimental prototype is developed to verify the theoretical analysis.
Harmonic Mitigation in 12-Pulse Bridge Rectifier Using DC Current Imposition Technique

P Saravana Prakash,R Kalpana,B Mohankrishna,Bhim Singh

DOI: https://doi.org/10.1109/pesgre45664.2020.9070283

2020-01-01

Abstract:To enhance the ability of harmonic suppression in a 12-pulse diode bridge rectifier (DBR) using a DC side current imposition technique is proposed in this paper. The 12-pulse operation is achieved by a zigzag auto-connected transformer. The standard 12-pulse DBR does not satisfy the IEEE-519 standard and thus the current imposition technique can be used on the DC side to mitigate the input line current harmonic distortion. The current imposition circuit on DC side contains a doubler circuit along with the tapped interphase transformer (TIPT). The zigzag configured autoconnected transformer has the function to avoid zero sequence components and thereby expel the need for zero-sequence blocking transformer. When the multi-winding interphase reactor is designed optimally, the pulse number of load voltage can be increased from 12 to 24 and by using the TIPT the pulse number of output voltage can be further increased from 24 to 36. The proposed configuration is analyzed and simulated in the MATLAB Simulink and validated with hardware results. The results show that the proposed method improves the power quality by reducing the total harmonic distortion in the input line current.
New 24-Pulse Rectifier With Passive Current Injection Circuit Based on Dual Auxiliary Transformers

Jingfang Wang,Chen Zhao,Tianlong Yu,Teng Liu,Xuliang Yao,Qiming Chen

DOI: https://doi.org/10.1109/jestpe.2023.3308188

IF: 5.462

2023-01-01

IEEE Journal of Emerging and Selected Topics in Power Electronics

Abstract:To enhance the harmonic mitigation capacity of the 12-pulse rectifier, a series-connected 24-pulse rectifier with a passive current injection circuit based on dual auxiliary transformers (PCIC-DAT) is proposed. The proposed PCIC-DAT is installed on the dc side of the proposed rectifier in parallel. The PCIC-DAT generates a specific square-wave current first, then the square-wave current is injected into the connection point of the two three-phase bridge rectifiers (TPBRs) so that the working modes of two TPBRs can be increased, and the series-connected 12-pulse rectifier is converted into a new 24-pulse rectifier subsequently. The resulting rectifier draws an approximately sinusoidal input current (THD < 5%) and has a smaller ripple output voltage. The PCIC-DAT contains only a pair of low KVA rating (0.985% $P_{d}$ ) auxiliary transformers with identical construction. The maximum current through the diodes in PCIC-DAT is only 3.4% of the load current. The proposed scheme has the merits of simple circuit configuration, small kVA rating, and low conduction loss, and thus, it has better application potential in industrial occasions. A 1.5 kW output power experimental prototype is established for testing to verify the harmonic reduction performance and the theory analysis.

engineering, electrical & electronic
Active Harmonic Suppression in a Series 12-Pulse Rectifier

Y. Shuanglian,Ding Zexiang,Zhang Damin,Lin Zhiyong,Li Yonghu,Xu Weidong

DOI: https://doi.org/10.1109/PEAC56338.2022.9959232

2022-11-04

Abstract:Traditional DC-side active harmonic method has the problems of complex circuit structure and great power losses. This paper suggests an active harmonic suppression technique on the DC side to enhance the harmonic suppression capabilities of the input side of the series 12-pulse rectifier. This method uses an inverter circuit with a center-tapped transformer to generate a square wave voltage and inject it into the DC side, adjust the output current of the rectifier, and then adjust the rectifier’s input current so that it closely resembles a sine wave based on the relationships between the DC side’s injection voltage and the AC side’s current flow. The analysis and simulation structure show that when the load changes, the grid-side current’s overall harmonic distortion rate is below 3.5%, and this strategy can effectively suppress the harmonics of the rectifier input current.

Engineering
An Approach to Harmonic Suppression Based on Triple Harmonics Injection with Passive Circuit

LI Xiaoqing,CHEN Guozhu

DOI: https://doi.org/10.3321/j.issn:1000-1026.2007.14.011

2007-01-01

Abstract:A new passive approach to reducing the input current’s harmonics of a three-phase diode rectifier based on the injection of the third harmonic current is proposed in this paper. In contrast to previous approaches,the star-connected capacitor is adopted to substitute for a transformer as the injection circuit, which operates in the serial resonant state at third harmonic frequency to enhance the circulating harmonic current in amplitude. The principle of harmonic suppression and the implementation of the third injection current are described first. Then, the characteristics of the circuit including the condition for optimal injection, the effects of component parameters’ deviation, the load varying range as well as component parameters’ error are analyzed in detail. Experimental results show that the new approach has better harmonic suppression performance than passive filtration while simpler and more reliable than active filtration, which gives it broad prospects for future application.
Harmonic Suppression Strategy Of 12-Pulse Controlled Rectifier

Y. Shuanglian,Cheng Jianxiong,Ding Zexiang,R. Xiaoqing,Zhang Damin

DOI: https://doi.org/10.1109/CIEEC54735.2022.9846619

2022-05-27

Abstract:In order to improve the harmonic suppression ability of 12-pulse controlled rectifier, a DC-side harmonic suppression scheme based on predictive current control strategy is studied. The control strategy improves the input current waveform of the rectifier by adding a boost converter circuit on the DC-side to meet the requirements of input current harmonic suppression under different load conditions. According to the current relationship between AC and DC sides of 12-pulse rectifier and the ideal current waveform at DC side, this paper analyzes and gives the input current waveform of boost converter circuit, and uses PWM method to adjust the input current of boost converter. Simulation results show that this method can effectively suppress the input current harmonics of 12-pulse controlled rectifier.

Engineering
Harmonic Suppression Technology of Three-Phase Diode Rectifier Based on Third Harmonic Current Injection

Xiaoqing Li,Guozhu Chen

DOI: https://doi.org/10.1109/epe.2007.4417760

2007-01-01

Abstract:The approaches to reduce input current's harmonics of three-phase diode rectifier based on injection of third harmonic current is studied in this paper. Two ways, the passive and the active, of implementation of injection are introduced. The mechanism of THD reduction and the structure of star-connected capacitors are introduced. Because it tunes at frequency of third harmonics with serial resonance, the passive circuit enhances the efficiency of circulating current with limited voltage source. Optimal injection conditions and characteristics of the circuit are also given in details. While the active method, which adds an ac voltage regulation circuit to the passive and based on Pulse-Width Modulation (PWM) technology is investigated too. It acts as a controllable resistor so that the third injection current can be controlled according to the optimal condition. Results of simulation and experiments show: the passive approach has acceptable harmonic suppression performance in certain cases, while the active one is more suitable for the application of wide-range variable loads or higher performance required.
A Simple 24-Pulse Rectifier Employing an Auxiliary Pulse-Doubling Circuit

Jingfang Wang,Anchen Chen,Xuliang Yao,Lei Li,Yusheng Lv,Qiming Chen

DOI: https://doi.org/10.1109/tpel.2022.3141705

IF: 5.967

2022-07-01

IEEE Transactions on Power Electronics

Abstract:A simple 24-pulse rectifier that provides low-harmonic utility power interface is proposed in this article. The proposed 24-pulse rectifier consists of a 12-pulse rectifier using a zigzag phase-shifting transformer and an auxiliary pulse-doubling circuit (APDC). Two auxiliary diodes in the APDC extract specific rectangular currents from the dc side of the rectifier to modulate and increase the output states of three-phase rectification bridges first, and then the 12-pulse rectifier is extended to a 24-pulse rectifier in accordance with the current relationship between ac and dc sides. The main low-order harmonics, such as 11th and 13th, are reduced markedly from the input line current and the proposed rectifier draws near-sinusoidal input line currents with less than 5 THD from the utility. The maximum current flowing through the two auxiliary diodes in APDC is only 3.4 of the load current and the capacity of APDC is only 3.06 of the output power. Thus, the proposed scheme is inexpensive and easy to implement and has a simple circuit configuration. Theoretical analyses were experimentally verified using a 1.7-kW experimental prototype.

engineering, electrical & electronic
A modified 72-pulse rectifier for harmonic suppression in more electric aircraft applications

Rohollah Abdollahi,Ahmad Salemnia,Gevork B. Gharehpetian

DOI: https://doi.org/10.1109/tte.2023.3315140

IF: 6.519

2023-01-01

IEEE Transactions on Transportation Electrification

Abstract:A parallel-connected 72-pulse rectifier (72PR) based on a 36PR with a passive harmonic mitigation method (PHMM) is proposed for harmonic mitigation in more electric aircraft applications. The PHMM is connected to the 36PR DC-side and consists of two harmonic reduction circuits (HRCs) and contains a four-tapped interphase reactor (FTIR) and four auxiliary diodes. Since the proposed design only requires a low-capacity PHMM (about 0.23% of the load power) and does not need any switching and control circuits, therefore; the proposed 72PR is a modified and low-cost solution. On the other hand, by using the proposed circuit, the input current is almost sinusoidal and its input current total harmonic distortion (THD) is less than 1%, which meets the IEEE-519 standard. In addition, the input current harmonic components at 400Hz-800Hz are less than the requirements mentioned in the DO-160G standard without using any input and output filters. Also, in all types of diode open-circuit faults, the proposed improved 72PR shows more fault-tolerant behavior and better performance in THD reduction. In the paper, the effectiveness of the proposed 72PR in reducing harmonic distortion is confirmed, using simulation and experimental results.

engineering, electrical & electronic,transportation science & technology
Multi-Pulse Rectifier Based on an Optimal Pulse Doubling Technique

Rohollah Abdollahi,Gevork B. Gharehpetian,Fazel Mohammadi,Saravana Prakash P

DOI: https://doi.org/10.3390/en15155567

IF: 3.2

2022-07-31

Energies

Abstract:This paper presents pulse multiplication technology based on an optimal Pulse Doubling Technique (PDT) to upgrade a 28-Pulse Rectifier (28-PR) to a 56-PR. The optimal PDT comprises a Tapped Interphase Reactor (TIPR) with a low kVA-rating and two diodes. The number of pulses can be increased from 28 to 56 using the PDT so that the input current harmonics are reasonably mitigated. Additionally, the 14-phase Polygon-Connected Autotransformer (PCA) is designed in such a way that it can be used for retrofit applications. A detailed simulation analysis in the MATLAB/Simulink environment is carried out, and the results show that the improved quality indices of the final AC input and DC output power are equivalent to the IEEE 519-2014 standard and meet sensitive industrial application requirements with an input current Total Harmonic Distortion (THD) lower than 3%. Moreover, the power factor also maintained unity for a wide operating range. The optimal PDT scheme is affordable and easy to implement as only a small-capacity PDT (only 1% of the output power) is needed to double the pulse number. An experimental prototype is developed to verify the simulation results.

energy & fuels

An Improved Multi-Pulse Rectifier Circuit for Input Current Harmonic Suppression Using Passive Devices

An Effective Method to Suppress Resonance in Input LC Filter of a PWM Current-Source Rectifier

Passive Harmonic Reduction for 12-Pulse Rectifier Using two Kinds of Unconventional Multi-tap Inter-Phase Reactors

Current Source PWM Rectifier Based on Indirect Current Control

Control of PWM Rectifier under Unbalanced Input Voltages

A Multipulse Pattern Modulation Scheme for Harmonic Mitigation in Three-Phase Multimotor Drives

A Novel Series 24-Pulse Rectifier Operating in Low Harmonic State Based on Auxiliary Passive Injection at DC Side

A Harmonic Current Suppression Method for Single-Phase PWM Rectifier Based on Feedback Linearization

Low harmonic 12-pulse rectifier with a circulating current shaping circuit

Novel passive harmonic suppression method for series-connected multi-pulse rectifiers

Input Current Step-Tripling for 12-Pulse Rectifier Using a Passive Four-tap Changer

A New Auxiliary Pulse Multiplication Scheme for Harmonic Suppression of the 12-Pulse Rectifier

Harmonic Mitigation in 12-Pulse Bridge Rectifier Using DC Current Imposition Technique

New 24-Pulse Rectifier With Passive Current Injection Circuit Based on Dual Auxiliary Transformers

Active Harmonic Suppression in a Series 12-Pulse Rectifier

An Approach to Harmonic Suppression Based on Triple Harmonics Injection with Passive Circuit

Harmonic Suppression Strategy Of 12-Pulse Controlled Rectifier

Harmonic Suppression Technology of Three-Phase Diode Rectifier Based on Third Harmonic Current Injection

A Simple 24-Pulse Rectifier Employing an Auxiliary Pulse-Doubling Circuit

A modified 72-pulse rectifier for harmonic suppression in more electric aircraft applications

Multi-Pulse Rectifier Based on an Optimal Pulse Doubling Technique