Preparation and Properties of Er-Doped ZrO2 Nanocrystalline Phase-Separated Preforms of Optical Fibers by MCVD Process

Anirban Dhar,Ivan Kasik,Ondrej Podrazky,Vlastimil Matejec,Bernard Dussardier
DOI: https://doi.org/10.1111/j.1744-7402.2011.00669.x
2011-12-01
Abstract:The fabrication of Er-doped ZrO2-based nanocrystalline phase-separated silica optical preforms by the MCVD and solution doping techniques is presented. Fabricated preform cores are nearly transparent and contain phase-separated rare-earth doped nanocrystalline particles with diameters mainly in a range from 20 to 80 nm. High concentrations of erbium and aluminium in preform cores of about 0.3 and 14 mol%, respectively have been achieved without defects on the core-cladding interface. Spectral losses in a range 800-1600 nm and fluorescence spectra of erbium ions around 1550 nm measured on a fibre drawn from the preform are reported.
Materials Science,Optics
What problem does this paper attempt to address?
The main problem that this paper attempts to solve is to develop a reliable and mature technology for preparing erbium (Er) - doped zirconia (ZrO2) - based nanocrystalline phase - separated fiber preforms containing nanocrystalline phase separation, and finally draw fibers with excellent performance. Specifically, the author hopes to achieve the following goals by improving the traditional modified chemical vapor deposition (MCVD) process and solution doping techniques: 1. **Increase the doping concentration of erbium ions**: Achieve high - concentration doping of erbium ions (about 0.3 mol%) and aluminum (about 14 mol%) while maintaining a defect - free core - cladding interface. 2. **Optimize the formation of nanocrystals**: Promote the nucleation and growth of nanocrystals by controlling the selection of dopants and heat - treatment conditions, so that the size of nanocrystals is mainly concentrated between 20 and 80 nanometers. 3. **Improve the optical properties of fibers**: Reduce the spectral loss of fibers in the wavelength range of 800 - 1600 nm, and optimize the fluorescence characteristics of erbium ions near 1550 nm to meet the application requirements of fiber amplifiers and lasers. To achieve these goals, the author carried out systematic experimental research, including preform preparation, heat - treatment, characterization, as well as fiber drawing and performance testing. By optimizing the MCVD process parameters and solution doping formulations, the author successfully prepared fiber preforms with the above - mentioned characteristics and carried out detailed characterization and performance evaluation on them. ### Key Technologies and Methods - **MCVD Process**: Used to deposit multi - layer - structured preforms. - **Solution Doping Technique**: Introduce dopants into the porous layer by the impregnation method. - **Heat - Treatment**: Conduct heat - treatment at a specific temperature to promote the formation of nanocrystals. - **Characterization Means**: Use electron probe micro - analysis (EMA), scanning electron microscope (SEM), transmission electron microscope (TEM), etc. to analyze the microstructure and composition of preforms and fibers. ### Main Results - Successfully prepared erbium - doped zirconia - based fiber preforms containing nanocrystalline phase separation. - Achieved high - concentration doping of erbium ions and aluminum, and there are no obvious defects at the core - cladding interface. - Observed nanocrystals with diameters in the range of 20 - 400 nm, most of which are in the range of 20 - 80 nm. - Preliminary tests show that the fiber exhibits good fluorescence characteristics at the wavelength of 1550 nm, but there is a relatively high background loss, which may be due to the scattering loss caused by nanocrystals. ### Future Work The author points out that it is necessary to further optimize the preparation process to reduce the background loss and improve the overall performance of the fiber, making it more suitable for applications in fields such as fiber amplifiers. In addition, more in - depth nano - scale analysis and spectroscopy studies are required to better understand the influence of nanocrystals on the optical properties of erbium ions.