Abstract:This review article describes the performance of the magnetic field measuring and monitoring systems for the Compact Muon Solenoid (CMS) detector. To cross-check the magnetic flux distribution obtained with the CMS magnet model, four systems for measuring the magnetic flux density in the detector volume were used. The magnetic induction inside the 6 m diameter superconducting solenoid was measured and is currently monitored by four nuclear magnetic resonance (NMR) probes installed using special tubes outside the barrel hadron calorimeter. Two more NRM probes were installed at the faces of the tracking system. The field inside the superconducting solenoid was precisely measured in 2006 in a cylindrical volume of 3.448 m in diameter and 7 m in length using 10 three-dimensional (3D) B-sensors based on the Hall effect. These B-sensors were installed on each of the two propeller arms of an automated field-mapping machine. In addition to these measurement systems, a system for monitoring the magnetic field during the CMS detector operation has been developed. Inside the solenoid in the horizontal plane, 4 3D B-sensors were installed at the faces of the tracking detector. Twelve 3D B-sensors were installed on the surfaces of the flux-return yoke nose disks. Seventy 3D B-sensors were installed in the air gaps of the CMS magnet yoke. A specially developed flux loop technique was used for the most complex measurements of the magnetic flux density inside the steel blocks of the CMS magnet yoke. The flux loops are installed in 22 sections of the flux-return yoke blocks. The areas enclosed by these coils varied from 0.3 to 1.59 m$^{2}$ in the blocks of the barrel wheels and from 0.5 to 1.12 m$^{2}$ in the blocks of the yoke endcap disks. The development of these systems and the results of the magnetic flux density measurements across the CMS magnet are presented and discussed in this review article.

Analysis of Eddy Current Distributions in the CMS Magnet Yoke During the Solenoid Discharge

Flux Loop Measurements of the Magnetic Flux Density in the CMS Magnet Yoke

Measuring the Magnetic Flux Density in the CMS Steel Yoke

Developing the Technique of Measurements of Magnetic Field in the CMS Steel Yoke Elements With Flux-Loops and Hall Probes

Electric Probe Measurements at Edge Region During H‐Mode Discharges in KSTAR

Measuring the Magnetic Flux Density with Flux Loops and Hall Probes in the CMS Magnet Flux Return Yoke

Using the Standard Linear Ramps of the CMS Superconducting Magnet for Measuring the Magnetic Flux Density in the Steel Flux Return Yoke

Finite Element Analysis of Gradient Z-Coil Induced Eddy Currents in a Permanent MRI Magnet

The CMS Magnetic Field Measuring and Monitoring Systems

Validation of the CMS Magnetic Field Map

Development of the CMS Magnetic Field Map

Influence of the high granularity calorimeter stainless steel absorbers onto the Compact Muon Solenoid inner magnetic field

Calculation of Forces to the High Granularity Calorimeter Stainless Steel Absorbers Misaligned inside the CMS Superconducting Coil

Calculation of Forces on the High Granularity Calorimeter Stainless Steel Absorber Plates in the Compact Muon Solenoid Magnetic Field

The Eddy Current Probe Array for Keda Torus Experiment.

Measurement of Toroidal Vessel Eddy Current During Plasma Disruption on J-TEXT

The Mechanical Performance Analyses of CFETR CSMC Preload Components Under Testing Current

Determination of Plasma Displacement Based on Eddy Current Diagnostics for the Keda Torus Experiment

Analytical Calculation and Experimental Verification of Superconducting Electrodynamic Suspension System Using Null-Flux Ground Coils

Measurement of Helicity Flux Density Using the Eddy-Current Diagnostic System in Keda Torus Experiment Device

A Distributed Current Source Model for Analyzing Motion-Induced Eddy-Current in a Conductor with Arbitrary Movements