Abstract:In this paper we introduce a method of calculating the local temperature and chemical potential inside a mesoscopic device out of equilibrium. We show how to check the conditions of local thermal equilibrium as the whole system is out of equilibrium. Especially we study the onsite chemical potentials inside a chain coupled to two reservoirs at a finite voltage bias. In the presence of disorder we observe a large fluctuation in onsite chemical potentials, which can be suppressed by the electron-electron interaction. By taking average with respect to the configurations of disorder, we recover the classical picture where the voltage drops monotonously through the resistance wire. We prove the existence of local intensive variables in a mesoscopic device which is in equilibrium or not far from equilibrium.
What problem does this paper attempt to address?
The problem that this paper attempts to solve is the calculation of local temperature and chemical potential inside mesoscopic devices in non - equilibrium states. Specifically, the author aims to introduce a method to check whether mesoscopic devices satisfy the local thermal equilibrium condition and calculate the local temperature and chemical potential on this basis. This is crucial for understanding the thermodynamic properties of mesoscopic systems in non - equilibrium states.
### Specific description of the problem
1. **Non - equilibrium states in mesoscopic systems**:
- In mesoscopic transport, when the system is driven far from equilibrium, how to define and calculate local thermodynamic variables (such as temperature and chemical potential) is a challenge.
- Traditional statistical mechanics methods are difficult to be directly applied to non - equilibrium systems because these methods are usually based on variational principles, and this principle is no longer applicable when far from equilibrium.
2. **Verification of local thermal equilibrium conditions**:
- Even if the whole system is in a non - equilibrium state, some small regions may still be close to local thermal equilibrium. Therefore, a method is needed to verify whether these regions satisfy the local thermal equilibrium condition.
3. **Calculation of local temperature and chemical potential**:
- The author proposes a method of introducing an auxiliary site to measure local temperature and chemical potential. This auxiliary site is coupled with the region of interest, and the local thermodynamic parameters can be determined by adjusting its energy level.
### Main contributions of the paper
- **Introduction of a new calculation method**: The author provides a method based on the density matrix to calculate local temperature and chemical potential, which is applicable to mesoscopic devices in non - equilibrium states.
- **Verification of local thermal equilibrium conditions**: By introducing an auxiliary site and checking whether it reaches local thermal equilibrium, the local thermal equilibrium conditions of the system are verified.
- **Application examples**: The author applies this method to a disordered chain model and studies the distribution of local chemical potential under different disorder intensities and reservoir voltage biases.
### Formula presentation
To ensure the correctness and readability of the formulas, the following are some key formulas involved in the paper:
1. **Fermion occupation number formula**:
\[
n_d=\frac{1}{e^{\beta(\epsilon_d - \mu)}+ 1}
\]
where \(\epsilon_d\) is the energy level, \(\beta\) is the reciprocal of temperature, and \(\mu\) is the chemical potential.
2. **Occupation number formula in the steady - state limit**:
\[
n_d=\frac{\Gamma}{\pi}\int_{-\infty}^{\infty}d\epsilon\frac{1}{e^{\beta(\epsilon - \mu)}+ 1}\frac{1}{(\epsilon - \epsilon_d)^2+\Gamma^2}
\]
In the weak - coupling limit, \(\Gamma\rightarrow0\), we can get:
\[
\frac{\Gamma}{\pi}\frac{1}{(\epsilon - \epsilon_d)^2+\Gamma^2}\rightarrow\delta(\epsilon - \epsilon_d)
\]
3. **Logarithmic relation formula**:
\[
\ln\left(\frac{1}{n_d}-1\right)=\beta\epsilon_d-\beta\mu
\]
Through these formulas, the author shows how to extract information about local temperature and chemical potential from experimental data.
In conclusion, this paper solves the problem of calculating local temperature and chemical potential in mesoscopic devices in non - equilibrium states, providing new tools and methods for understanding the thermodynamic behavior of mesoscopic systems.