Colloidal Mikado: Rheology and Structure of Thermoreversible Gels of Sticky Rod-Like Particles
Naveen Reddy,Zhenkun Zhang,M. P. Lettinga,Jan K. G. Dhont,Jan Vermant
IF: 4.167
2010-01-01
AIChE Journal
Abstract:The assembly of rod-like particles by weak attractive interactions is important for the properties of several soft biological materials as well as in tailoring the properties of colloidal gels in a variety of applications. Understanding the link between the physicochemical parameters such as size and aspect ratio, volume fraction, interparticle forces with the resulting microstructure and the rheological response remains however challenging. It is often difficult to obtain a good control over these parameters due to the lack of suitable model systems. In the present work a model rod-like fd-virus particle has been surface modified with a thermoreversible polymer poly(N-isoproplyacrlyamide). The repulsive and attractive contributions to the overall interaction potential can be varied independently by changing the ionic strength and the temperature. The effects of these changes on the strength and structure of the gel have been studied near the gel transition using a combination of rheological and scattering measurements. The results show that for these thermoreversible ’sticky’ rod systems, the variations of the structure in the gelled state are relatively weak, with the gel strength mainly being controlled by the relative magnitudes between the attractive and repulsive contributions and the volume fraction, the anisotropic nature of the electrostatic interactions seems to have a minor effect. Introduction: Anisotropic rodlike particles are effective basic building blocks for strong structures with low solid content. This property stems from the excluded volume effects which results in low percolation threshold to form networks [1, 2]. There are several examples from science and technology. Actin filaments and microtubules are used in strengthening the cytoskeleton of living cells [3], rod-like and disc-like clay particles were used for ages in pottery to induce plasticity and to make them permeable to air [4] and more recently anisotropic nanoparticles such as carbon nanotube or graphene are used to strengthen polymer composites [5]. The fundamental study of gels prepared using rodlike particles was hampered by the lack of suitable model systems. Typically the control over the interaction potential is poor and the particles were polydisperse. In the present work, the mechanical and structural properties of gels composed out of monodisperse rodlike particles are investigated. By restricting our observations to the region close to the gel transition, were a critical gel is observed, the effects of changing the interactions on the strength and the structure of the gel can be investigated in detail. Rheological and scattering studies of nearly critical gels made of fd -viruses (monodisperse, negatively charged rodlike particles) grafted with the thermoresponsive polymer poly(N-isoproplyacrlyamide) (hereafter referred as PNIPAM) [6] are presented. Control over the inter-particle interactions is achieved by changing the attractive interaction with temperature, by altering the hydrophobicity of the PNIPAM polymer, and changing the repulsive interaction by varying the ionic strength of the suspension. Results and discussion: The phase diagram of the fd-PNIPAM suspensions is shown in figure 1.a. To make gels with low solid content and to exclude effects of liquid crystalline ordering, this study is limited to the isotropic regime. Suspensions were prepared in aqueous buffers of three different ionic strengths, i.e. 1, 5, 105 mM respectively. For each of these ionic strengths the particle concentration has been varied, as shown in figure 1.a. The effective diameter of the fd-PNIPAM particles is a function of the ionic strengths and temperature, as show in figure 1.b and c. For temperatures below the gel point the grafted polymer is in a coil state and acts as a stearic stabilizer. As the temperature is increased above the gel point, the PNIPAM chains collapse into a globular structure and the polymer becomes hydrophobic. Thus a short attractive interaction can be induced by increasing the temperature. Repulsive interactions are tuned by changing the electrostatic double layer thickness. For fd-PNIPAM particles in aqueous buffer solutions at 105 mM, the double layer thickness is smaller than the collapsed PNIPAM layer thickness, therefore the inter-particle potential is predominantly attractive. As the double layer thickness is made to be larger (low ionic strength) the electrostatic repulsions will also contribute significantly to the overall potential, leading to a repulsive system at low temperatures and a system with a weaker attractive interaction at high temperature. For fd-PNIPAM in a 1 mM ionic strength buffer, the electrostatic double layer is much larger than the collapsed PNIPAM polymer. This increases the gel temperature from 32C for fd-PNIPAM in 105 mM buffer to 35C in 1 mM buffer, see figure 1.d. The gelation point was determined by dynamic light scattering by measuring the transition from an ergodic to non-ergodic system, and by measurements of the linear viscoelastic properties, measuring where the phase angle, tan(δ), becomes independent of frequency [7, 8] Figure 2.a shows the change in the average storage modulus (at a frequency of 6.28 rad/s) as a function of fd-PNIPAM particle concentration at ∆T = 6.2 nm 1 mM 5 mM 105 mM