[On speech loss after encephalitis].

M. Mumenthaler,J. Wunderli

DOI: https://doi.org/10.1007/BF00345278

Abstract:

What problem does this paper attempt to address?

Solvation mechanisms of nedocromil sodium from activation energy and reaction enthalpy measurements of dehydration and dealcoholation

Alison C Richards,Ian J McColm,J Barrie Harness

DOI: https://doi.org/10.1002/jps.10047

Abstract:Two independent athermal methods of analysis have been used to determine the activation energies associated with the dehydration of nedocromil sodium hydrates. For the highest temperature reaction, monohydrate to the anhydrate, the differences in the measured activation energies indicate a three-dimensional nucleation mechanism in the bulk of the crystal with subsequent three-dimensional anhydrate crystal growth. The number of critical nuclei varies inversely with heating rate. Measured enthalpy values for successive removal of water molecules at 31.7 +/- 1.0, 91.3 +/- 0.8, and 193 +/- 0.6 degrees C are the same, within experimental error, at 21.6 +/- 2.6 kJ (mol H(2)O)(-1), as determined from differential thermal analysis traces. This result implies that an earlier concept of "strong" and "weak" water binding is not relevant and temperatures at which H(2)O molecules are removed is related to nucleation effects and not bond energies. The low temperature shoulder on the 91.3 degrees C peak is identified as an effect arising from open pan analysis conditions. The appearance of "transient" peaks in the conditioning stage of nedocromil sodium trihydrate thermal analysis experiments have been investigated and an explanation based on the presence of alcoholates [(NS)(4) small middle dot 5CH(3)OH, (NS)(5) small middle dot 9C(2)H(5)OH, and (NS)(2) small middle dot C(3)H(7)OH] in the preparations is proposed.
Dehydration behavior of nedocromil magnesium pentahydrate

H Zhu,D J Grant

DOI: https://doi.org/10.1016/s0378-5173(00)00700-6

2001-03-14

Abstract:The dehydration of nedocromil magnesium (NM) pentahydrate proceeds in two steps, corresponding to the loss of four water molecules in the first step and one water molecule in the second step. The effects of temperature, particle size, sample weight, water vapor pressure and dehydration-rehydration cycle on both the kinetics and activation energy of the dehydration of NM pentahydrate were studied using isothermal TGA and temperature-ramp DSC analyzed by Kissinger's method. The dehydration kinetics for both steps are best described by the Avrami-Erofeev equations, suggesting a nucleation-controlled mechanism. The high activation energy for the second dehydration step indicates that the last water molecule, which is bonded both to a magnesium ion and to a carboxylate oxygen atom, is more 'tightly bound'. The activation energy decreased with increasing sample weight and decreasing particle size. The dehydration rate increased with decreasing water vapor pressure and with repetition of the dehydration-hydration cycle. Dynamic and isothermal PXRD, and 13C solid-state NMR were employed to provide an insight into the dehydration mechanism and the nature of solid-state phase transformation during the dehydration. Molecular modeling with Cerius(2) was used to visualize the crystal structure and to construct the molecular packing diagram. A correlation was noted between the dehydration behavior and the bonding environment of the water molecules in the crystal structure.
Sodium nitroprusside alters Ca2+ flux components and Ca2(+)‐dependent fluxes of K+ and Cl‐ in rat aorta.

L. Magliola,A. W. Jones

DOI: https://doi.org/10.1113/jphysiol.1990.sp017952

1990-02-01

Journal of Physiology

Abstract:1. Sodium nitroprusside (NP) caused both an inhibition of a noradrenaline (NA)‐induced contraction and an elevation of cyclic guanosine 3',5'‐monophosphate (cyclic GMP) in rat aorta. Both NP‐induced responses were enhanced by the selective cyclic GMP phosphodiesterase inhibitor, M&B 22948 (2‐o‐propoxyphenyl‐8‐aza‐purin‐6‐one, 30 microM). 2. The inhibition of a NA‐induced contraction by NP was characterized by dissociating the intracellular Ca2+ release component from the extracellular Ca2+ influx component of the contraction. The transient contraction stimulated by NA in the absence of extracellular Ca2+ was inhibited by NP. Also, the slowly developed tension stimulated by NA in aortas depleted of stored Ca2+ and subsequently exposed to extracellular Ca2+ was inhibited by NP. Both components of contraction were equally sensitive to NP. 3. NA stimulated both unidirectional 45Ca2+ influx in the presence of extracellular Ca2+ and 45Ca2+ efflux into a 0 Ca2+ solution that contained 2 mM‐ethyleneglycol‐bis‐(beta‐aminoethylether)N,N'‐tetraacetic acid (EGTA). The increased 45Ca2+ efflux is thought to reflect release of stored Ca2+ followed by membrane transport. NP greater than 10 nM inhibited both 45Ca2+ influx and release components whereas NP at 1‐3 nM enhanced NA‐stimulated 45Ca2+ efflux and relaxed the maintained tension caused by NA in 0 Ca2+, 2 mM‐EGTA. 4. NP also inhibited the Ca2(+)‐dependent 42K+ and 36Cl‐ effluxes from rat aorta stimulated either by NA or by high potassium. NP inhibited the contractile and flux responses to NA more effectively than the responses to high potassium. 5. These data indicate that: (1) NP reduces cytosolic Ca2+ by the combined inhibitory effects on Ca2+ influx and intracellular Ca2+ release, and by the stimulation of a Ca2(+)‐ATPase; and (2) the differential sensitivity of the NA and high‐potassium responses to NP may reflect underlying differences in Ca2+ handling induced by receptor occupancy and depolarization.
Moisture sorption kinetics for water-soluble substances. II: Experimental verification of heat transport control

L Van Campen,G L Amidon,G Zografi

DOI: https://doi.org/10.1002/jps.2600721205

Abstract:The rates of water sorption as a function of relative humidity for water-soluble substances exhibiting deliquescence have been measured in an atmosphere of pure water vapor. The substances studied included a series of alkali halides, choline halides, and sugars. The results were compared with a theoretical model, previously described, which relates the rate of water uptake to the transport of heat produced during the process away from the surface. Taking into account the heat of water vapor condensation, heat of solution, and heat of hydration, when hydration occurs, the model allows excellent a priori prediction of water uptake rates as a function of relative humidity.
Extension of Clausius-Clapeyron equation to predict hydrate stability at different temperatures

L R Chen,D J Grant

DOI: https://doi.org/10.3109/10837459809028630

Abstract:The objectives of this study were to verify theoretically and experimentally that the Clausius-Clapeyron equation can be applied to a hydrate system, and to use this equation to predict the equilibrium water activity for a hydrate pair existing in equilibrium at different temperatures for the determination of the ranges of hydrate stability. The Clausius-Clapeyron equation was derived for hydrate systems by assuming (a) the higher and the lower hydrates exist in equilibrium with water vapor as three pure phases; and (b) the overall volume change involved in this equilibrium process is approximated by the volume of the released water vapor, which behaves ideally. The equilibrium water vapor pressure at different temperatures for the nedocromil sodium monohydrate and trihydrate system was determined dynamically using a thermogravimetric analyzer with an attached water vapor delivery system. The enthalpy of dehydration obtained by applying the Clausius-Clapeyron equation to the experimentally determined equilibrium water vapor pressures is in fair agreement with the enthalpy of dehydration derived from differential scanning calorimetry (13.7 +/- 0.6 kcal/mol of water loss, n = 5), indicating that the Clausius-Clapeyron equation can indeed be applied to organic hydrate systems. The application of the Clausius-Clapeyron equation to predict the hydrate stability under various conditions is also discussed.
Humidity Effect on Diffusion and Structure of a Moisture-Swing CO2 Sorbent

Xiaoyang Shi,Hang Xiao,Xi Chen,Tao Wang,Klaus. S. Lackner

DOI: https://doi.org/10.48550/arXiv.1702.06534

2017-02-21

Abstract:Ion hydrations are ubiquitous in natural and fundamental processes. A quantitative analysis of a novel CO2 sorbent driven by ion hydrations was presented by molecular dynamics (MD). We explored the humidity effect on the diffusion and structure of ion hydrations in CO2 sorbent, as well as the working mechanism of the moisture-swing CO2 sorbent. The discovery of the diffusion coefficients of ions at different humidity levels can be applied to design a new CO2 sorbent with superior performance. The molecular structure analysis shows a higher precipitation rate of HCO3- ions than CO32- ions in a dry surrounding, which leads to a more alkaline surrounding on CO2 sorbent that may promote the absorption of CO2.

Chemical Physics
Moisture sorption kinetics for water-soluble substances. III: Theoretical and experimental studies in air

L Van Campen,G L Amidon,G Zografi

DOI: https://doi.org/10.1002/jps.2600721206

Abstract:As an extension of the model of heat transport control developed for the kinetics of water sorption by water-soluble substances from an atmosphere of pure water vapor, equations have been developed to account for limitations of diffusion on mass transport of water vapor when air is present. Although the inability to determine the vapor diffusion layer thickness prevents using these equations to predict sorption behavior a priori, minimum water sorption rates can be calculated by assuming a diffusion layer thickness equal to the sample chamber radius. Combining heat transport and mass transport produces equations which describe very well the observed sorption by three water-soluble salts in one atmosphere of air. As in the absence of air, sorption rates are predicted and observed to be constant at a given atmospheric relative humidity.
Gas Chromatographic Thermodynamics on Hydration Processes of Magnesium Chloride with Low Water

JJ Chen,GC Chen,PH Ma,JQ Bao,YT Ma,FQ Chen

DOI: https://doi.org/10.3969/j.issn.1008-858x.2002.02.005

2003-01-01

Abstract:The dehydration and hydration processes of magnesium chloride hydrates were studied by means of frontal chromatography analysis, calorimetry, thermogravimetry and chemical analysis. The mathematical imitation for the adsorption isotherms of MgCl2*4H2O and MgCl2*2H2O at different temperatures indicates that Boltzmann Function is the ideal equation to describe those adsorption isotherms. Its adsorption heat is -13.06kJ/mol and -16.11kJ/mol, respectively. The adsorption equilibrium constants are also given. From the data obtained, there is a thermodynamical possibility to use partial dehydrated magnesium chloride hydrates as an absorbance to clean water vapor contained in bischophite dehydration equipment and let the protection gas HCl recycle in the fluid bed reaction system.
Water vapor effect on the physico-geometrical reaction pathway and kinetics of the multistep thermal dehydration of calcium chloride dihydrate

Kazuki Kato,Mito Hotta,Nobuyoshi Koga

DOI: https://doi.org/10.1039/d4cp01870b

IF: 3.3

2024-06-19

Physical Chemistry Chemical Physics

Abstract:This study investigated how water vapor influences the reaction pathway and kinetics of the multistep thermal dehydration of inorganic hydrates, focusing on CaCl 2 ·2H 2 O (CC-DH) transforming into its anhydride (CC-AH) via an intermediate of its monohydrate (CC-MH). In the presence of atmospheric water vapor, the thermal dehydration of CC-DH stoichiometrically proceeded through two distinct steps, resulting in the formation of CC-AH via CC-MH under isothermal conditions and linear nonisothermal conditions at a smaller heating rate ( β ). Irrespective of atmospheric water vapor pressure ( p (H 2 O)), these reaction steps were kinetically characterized by a physico-geometrical consecutive process involving the surface reaction and phase boundary-controlled reaction, which was accompanied by three-dimensional shrinkage of the reaction interface. In addition, a significant induction period was observed for the second reaction step, that is, the thermal dehydration of CC-MH intermediate to form CC-AH. With increasing p (H 2 O), a systematic increase in the apparent Arrhenius parameters was observed for the first reaction step, that is, the thermal dehydration of CC-DH to form CC-MH, whereas the second reaction step exhibited unsystematic variations of the Arrhenius parameters. At a larger β in the presence of atmospheric water vapor, the first and second reaction steps partially overlapped; moreover, an alternative reaction step of the thermal dehydration of CC-MH to form CaCl 2 ·0.3H 2 O was observed between these reaction steps. The physico-geometrical phenomena influencing the reaction pathway and kinetics of the multistep thermal dehydration were elucidated by considering the effects of atmospheric and self-generated water vapor in a geometrically constrained reaction scheme.

chemistry, physical,physics, atomic, molecular & chemical
Spontaneous Crystalline-to-Amorphous Phase Transformation of Organic or Medicinal Compounds in the Presence of Porous Media, Part 3: Effect of Moisture

Ken K. Qian,Dale E. Wurster,Robin H. Bogner

DOI: https://doi.org/10.1007/s11095-012-0734-4

IF: 4.58

2012-03-20

Pharmaceutical Research

Abstract:PurposeAmorphization of crystalline compounds using mesoporous media is a promising technique to improve the solubility and drug release of poorly-soluble compounds. The objective of this paper is to understand the effect of moisture on the capacity and performance of vapor-phase mediated amorphization.MethodsMesoporous silicon dioxide (SiO2) and crystalline naphthalene were used as the model system. The effect of moisture on the amorphization capacity of naphthalene was determined using adsorption chambers with various levels of relative humidity. Enthalpy and capacity of water vapor adsorption on SiO2 were measured using isothermal microcalorimetry and thermogravimetry.ResultsMoisture not only suppressed the amorphization capacity of naphthalene, but reversed an already-amorphized formulation as well. On the other hand, through the same competitive interaction, improved drug release and enhanced solubility were obtained. The initial supersaturation was followed by an entropy-driven crystallization. In addition, moisture-induced siloxane bond fracture was found at normal processing conditions, which led to the changes in silica surface chemistry. However, the implication in amorphization has not reached a definitive conclusion.ConclusionsHumidity during processing and storage must be carefully controlled for this type of amorphous formulation. Further investigation is needed to better understand the moisture-induced changes of silica.

pharmacology & pharmacy,chemistry, multidisciplinary
Cooperation for secure wireless communications with resource-bounded eavesdroppers

N. Kolokotronis,Kyriakos Fytrakis,A. Katsiotis,N. Kalouptsidis

DOI: https://doi.org/10.1109/GLOCOMW.2014.7063626

2014-12-01

Abstract:Wireless communications system designs are sought that rely on the potential of the physical (PHY) layer to allow a transmitter-receiver pair communicate securely in the presence of one or more eavesdroppers. Communication is performed with the help of multiple trusted relays, via the decode-and-forward (DF) protocol, and assuming knowledge of global channel state information (CSI). Instead of dealing with information-theoretic security, we assume that eavesdroppers have bounded resources, and therefore we need to assure that the transmitted information is computationally secure; this is shown to impose constraints on the maximum power of the signals received by the eavesdroppers. The optimal relay weights that maximize the signal-to-noise ratio (SNR) difference SNRd - SNRe between the destination and the eavesdroppers are determined under various (transmit, security, reliability) power constraints. Closed-form solutions are obtained in some problem formulations for one eavesdropper, whereas an iterative algorithm is proposed if more eavesdroppers are present. Simulation results indicate that a higher SNR value (compared to the non-cooperative case) is attained at the destination, while satisfying the security constraints.
Physico-geometrical reaction pathway and kinetics of multistep thermal dehydration of calcium chloride dihydrate in a dry nitrogen stream

Kazuki Kato,Nobuyoshi Koga

DOI: https://doi.org/10.1039/d4cp00790e

IF: 3.3

2024-03-29

Physical Chemistry Chemical Physics

Abstract:Several inorganic hydrates exhibit reversible reactions of thermal dehydration and rehydration, which is potentially applicable to thermochemical energy storage. Detailed kinetic information on both forward and reverse reactions is essential for refining energy storage systems. In this study, factors determining the reaction pathway and kinetics of the multistep thermal dehydration of inorganic hydrates to form anhydride via intermediate hydrates were investigated as exemplified by the thermal dehydration of CaCl 2 ·2H 2 O (CC-DH) in a stream of dry N 2 . The formation of CaCl 2 ·H 2 O (CC-MH) as the intermediate hydrate is known during the thermal dehydration of CC-DH to form its anhydride (CC-AH). However, the two-step kinetic modeling based on the chemical reaction pathway considering the formation of the CC-MH intermediate failed in terms of the reaction stoichiometry and kinetic behavior of the component reaction steps. The kinetic modeling was refined by considering the physico-geometrical reaction mechanism and the self-generated reaction conditions to be a three-step reaction. The multistep reaction was explained as comprising the surface reaction of the thermal dehydration of CC-DH to CC-AH and subsequent contracting geometry-type reactions from CC-DH to CC-MH and from CC-MH to CC-AH occurring consecutively in the core of the reacting particles surrounded by the surface product layer of CC-AH. The acceleration of the linear advancement rate of the reaction interface during both contracting geometry-type reactions was revealed through multistep kinetic analysis and was described by a decrease in the water vapor pressure at the reaction interface as the previous reaction step proceeded and terminated.

chemistry, physical,physics, atomic, molecular & chemical
Nucleation kinetics in drying sodium nitrate aerosols

Joshua F. Robinson,Florence K. A. Gregson,Rachael E. H. Miles,Jonathan P. Reid,C. Patrick Royall

DOI: https://doi.org/10.48550/arXiv.1911.06212

2019-11-14

Soft Condensed Matter

Abstract:A quantitative understanding of the evaporative drying kinetics and nucleation rates of aqueous based aerosol droplets is important for a wide range of applications, from atmospheric aerosols to industrial processes such as spray drying. Here, we introduce a numerical model for interpreting measurements of the evaporation rate and phase change of drying free droplets made using a single particle approach. We explore the evaporation of aqueous sodium chloride and sodium nitrate solution droplets. Although the chloride salt is observed to reproducibly crystallise at all drying rates, the nitrate salt solution can lose virtually all of its water content without crystallising. The latter phenomenon has implications for our understanding of the competition between the drying rate and nucleation kinetics in these two systems. The nucleation model is used in combination with the measurements of crystallisation events to infer nucleation rates at varying equilibrium state points, showing that classical nucleation theory provides a good description of the crystallisation of the chloride salt but not the nitrate salt solution droplets. The reasons for this difference are considered.
Evolution of Chemical Bonding and Crystalline Swelling-Shrinkage of Montmorillonite upon Temperature Changes Probed by in Situ Fourier Transform Infrared Spectroscopy and X-ray Diffraction

Cunjun Li,Yanqi Xu,Yan Yang,Linjiang Wang,Chunhui Zhou

DOI: https://doi.org/10.1021/acs.langmuir.2c02236

IF: 3.9

2022-11-22

Langmuir

Abstract:Clay minerals are distributed in Earth's crust and troposphere and in Martian crust where temperature varies. Understanding the changes of chemical bonding and crystalline swelling-shrinkage of montmorillonite (Mnt) upon temperature changes is fundamental for studying its surface reactivity and interaction in specific surroundings. However, such an issue remains poorly understood. Here, in situ high- and low-temperature Fourier transform infrared (HT- and LT-FTIR) spectroscopy and X-ray diffraction (HT- and LT-XRD) were performed to study the evolution of chemical bonding and crystalline swelling-shrinkage of sodium-montmorillonite (NaMnt) upon temperature changes. The FTIR results show that the hydroxyl content in NaMnt decreased when the temperature increased from 20 to 700 °C, while it is independent of temperature from 0 to -150 °C. The formation of hydroxyls at the "broken" layer edges of NaMnt is related to adsorbed water molecules on the surfaces, and its content increased when the particle size of the NaMnt decreased. The water molecules in the interlayer space of NaMnt could bond to the tetrahedral sheet of NaMnt through Si2O-H2O bonds. HT- and LT-XRD results reveal that all of those water molecules in NaMnt were removed after heating to 100 °C in the heating chamber. The NaMnt was transformed from a state of monolayer interlayer water molecules at 20 °C to a dehydrated state at 100 °C, and then to a dehydroxylated state at 700 °C. Accordingly, the basal spacings of NaMnt were changed from 1.27 to 0.97 nm and then to 0.96 nm, respectively. When NaMnt was cooled from 20 to -268 °C, a crystalline swelling of NaMnt occurred with an increase of 0.03 nm of basal spacing. This work demonstrates that high/low temperature has a remarkable effect on the hydroxyls and the water molecules in NaMnt, which in turn affects its swelling-shrinkage performance. These findings provide some in-depth understanding of the changes of chemical bonding and crystalline swelling-shrinkage of montmorillonite upon temperature changes and the reasons behind these, which might be helpful for the design of engineering Mnt in high-/low-temperature applications.
Influence of Temperature on Solvent-Mediated Anhydrate-to-hydrate Transformation Kinetics.

Haiyan Qu,Tommy Munk,Claus Cornett,Jian X. Wu,Johan P. Bøtker,Lars P. Christensen,Jukka Rantanen,Fang Tian

DOI: https://doi.org/10.1007/s11095-010-0281-9

IF: 4.58

2010-01-01

Pharmaceutical Research

Abstract:To achieve an in-depth understanding of the underlying mechanism of the acceleration or deceleration effect of temperature on solvent-mediated anhydrate-to-hydrate phase transformation.
Internal Forces Within the Layered Structure of Na-Montmorillonite Hydrates: Molecular Dynamics Simulation

Yu-Chao Li,Sheng-Jie Wei,Nan Xu,Yi He

DOI: https://doi.org/10.1021/acs.jpcc.0c07597

2020-01-01

The Journal of Physical Chemistry C

Abstract:The hydration swelling property of bentonites, which mainly depends on the content and swelling capacity of montmorillonite (MMT), greatly contributes to many engineering applications such as grouting and barrier materials. Much efforts have been made to investigate the process of crystalline swelling by experimental tests, analytical models, and numerical simulations. However, most of the studies are limited to the microscopic structure of the hydrates and the variation of free energy of the system. Via molecular dynamics simulation, this paper discusses the internal forces within the layered structure of Na-MMT hydrates for the mechanical analysis of crystalline swelling. The repulsive force between crystal layers f(LL), the repulsive force of interlamellar water molecules to crystal layer f(WL), and the attractive force of interlamellar cations to crystal layer f(CL) in different hydration phases are calculated to illustrate the relationships among the microscopic structure of hydrates, internal forces, and the macroscopic characteristics of swelling. For fully dry Wyoming MMT, f(LL) is (3.85 +/- 0.39) x 10(-9) N/uc (positive for repulsion) and f(CL) is (-3.93 +/- 0.34) x 10(-9) N/uc (negative for attraction). With the increase of water content, the three forces reach relatively stable values, which are 3.43 x 10(-9), -4.99 x 10(-9), and 1.25 x 10(-9) N/uc for f(LL), f(CL), and f(WL), respectively. The quantitative analysis shows that the total repulsive force from f(LL) and f(WL) is approximately equal to the attractive force f(CL) during the process of crystalline swelling. The Coulomb electrostatic force term controls the f(LL) and f(CL), while it is comparable to but less than the van der Waals force term for f(WL). The Coulomb electrostatic force term of f(LL) may be regarded as an interaction between "infinite parallel charged plates" when the water content is greater than 6 H2O/uc. The Coulomb electrostatic force term of f(WL) is mainly caused by the polarization effect of interlamellar water molecules. The crystalline swelling can be presented as a stepwise "expansion-filling-saturation" process via the analysis of the change of average density of interlamellar water, whose values are close to the mass density of bulk water at the "saturation" stages.
Tailoring Crystallization Kinetics in Thin Sucrose Films during Convective Drying: Impact of Temperature and Humidity on Onset, Growth, and Nucleation Rate

Martin Schugmann,Petra Foerst

DOI: https://doi.org/10.3390/pharmaceutics16101260

IF: 6.525

2024-09-28

Pharmaceutics

Abstract:Drying experiments with varying air temperature and humidity were conducted to investigate the influence of the drying process on the crystallization of thin sucrose films. For the first time, the effects of the nucleation onset, nucleation rate, and growth rate were investigated in situ and their differentiated influence on product crystallinity could be assessed. The growth rate was not influenced by air humidity but showed a strong dependence on temperature. It increased with drying temperature; however, at high temperatures, growth was inhibited when the water content falls below a critical level. Noticeable differences in nucleation behavior could be observed with regard to air humidity. Dry air led to crystallization onsets at lower levels of supersaturation, while moderately humid air retarded it. At higher temperatures, nucleation onset commenced at lower water contents but at a constant supersaturation level. The nucleation rate doubled in experiments with moderately humid air (15% RH), while an elevated drying temperature showed generally lower nucleation rates. The observed differences in the nucleation onset and rate could be explained by the film-internal concentration profile, which is strongly influenced by drying parameters. The insights therefore provide a differentiated understanding of the formation of the physical state and how it can be influenced during convective drying.

pharmacology & pharmacy
Nanoscale Ion Dynamics Control on Amorphous Calcium Carbonate Crystallization: Precise Control of Calcite Crystal Sizes

Maria P. Asta,Alejandro Fernandez-Martinez,Juan Alonso,Laurent Charlet,Nathaniel Findling,Valerie Magnin,Beatrice Ruta,Michael Sprung,Fabian Westermeier

DOI: https://doi.org/10.1021/acs.jpcc.0c08670

2020-11-04

The Journal of Physical Chemistry C

Abstract:Amorphous calcium carbonate (ACC) is an essential component present during the early stages of biomineralization of many calcifying organisms, which is used as a precursor of crystalline calcium carbonate phases. Here, we performed X-ray photon correlation spectroscopy experiments on ACC which show that the amount of adsorbed water has a strong control over its diffusive dynamics. Results of crystallization experiments under conditions of controlled humidity indicate that the adsorbed water is enough to spark crystallization of calcite. A direct proportionality is found between the relative humidity of the environment and the final size of the calcite crystals. Different hypotheses are made to explain this result, with the confinement within the amorphous matrix being the main suspect of controlling the size of the crystallites. Control of water activity and water content is, therefore, a possible way to regulate biomineral crystallinity both in nature and for the design of functional biomimetic materials.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acs.jpcc.0c08670?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acs.jpcc.0c08670</a>.Methods; two-time correlation function of the sample ACC-250 °C; ATR–FTIR spectra of ACC and calcite; XRD of ACC and calcite; TGA–DSC of ACC and calcite; representative time-evolution of the intensity profile for ACC; COMSOL model of the diffusion of Ca versus distance and of calcite precipitated over time; calculated calcite SI and critical radius at different RH; fit parameters obtained from the intensity auto-correlation functions for ACC thermally untreated and treated samples; samples exposed to different levels of relative humidity measured by XPCS; and water content and crystallinity of synthesized ACC over time under different relative humidity conditions (<a class="ext-link" href="/doi/suppl/10.1021/acs.jpcc.0c08670/suppl_file/jp0c08670_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.
Hyphenation of Raman spectroscopy with gravimetric analysis to interrogate water-solid interactions in pharmaceutical systems

Alan D Gift,Lynne S Taylor

DOI: https://doi.org/10.1016/j.jpba.2006.06.025

2007-01-04

Abstract:A moisture sorption gravimetric analyzer has been combined with a Raman spectrometer to better understand the various modes of water-solid interactions relevant to pharmaceutical systems. A commercial automated moisture sorption balance was modified to allow non-contact monitoring of the sample properties by interfacing a Raman probe with the sample holder. This hybrid instrument allows for gravimetric and spectroscopic changes to be monitored simultaneously. The utility of this instrument was demonstrated by investigating different types of water-solid interactions including stoichiometric and non-stoichiometric hydrate formation, deliquescence, amorphous-crystalline transformation, and capillary condensation. In each of the model systems, sulfaguanidine, cromolyn sodium, ranitidine HCl, amorphous sucrose and silica gel, spectroscopic changes were observed during the time course of the moisture sorption profile. Analysis of spectroscopic data provided information about the origin of the observed changes in moisture content as a function of relative humidity. Furthermore, multivariate data analysis techniques were employed as a means of processing the spectroscopic data. Principle components analysis was found to be useful to aid in data processing, handling and interpretation of the spectral changes that occurred during the time course of the moisture sorption profile.
Nanoscale Control Over Water-Film Thickness Using Temperature Modulation: Tuning Mineral Carbonation Reactivity

Christopher J. Thompson,Sebastian T. Mergelsberg,Bavan P. Rajan,Paul F. Martin,Sebastien N. Kerisit,John S. Loring,Christopher J Thompson,Sebastian Mergelsberg,Bavan Rajan,Paul Martin,Sebastien Kerisit,John Steven Loring

DOI: https://doi.org/10.1039/d3en00884c

2024-03-08

Environmental Science Nano

Abstract:Induced temperature gradients within a high-pressure reactor were used to assess how the thickness of nanoscale water films affect the carbonation of forsterite, Mg 2 SiO 4 , in water-saturated supercritical carbon dioxide (scCO 2 ). Water monolayer (ML) coverages on the mineral surface were estimated by in situ infrared spectroscopy and were shown to increase nearly exponentially from approximately 5 to 170 ML when the forsterite region was cooled from +0.5 to -0.3 °C relative to a nearby pool of excess water. Carbonation rates and extents were strongly dependent on the water film thickness, with the highest rates and complete mineral conversion occurring within 40 hr under bulk-like water coverages. Reaction passivation, possibly due to a reduction in reactive surface area, was observed for thinner water films ranging from 5-53 ML. Temperature modulation can be an effective technique for investigating basalt reactivity over a range of water coverages in humidified scCO 2 .

environmental sciences,chemistry, multidisciplinary,nanoscience & nanotechnology

[On speech loss after encephalitis].

Solvation mechanisms of nedocromil sodium from activation energy and reaction enthalpy measurements of dehydration and dealcoholation

Dehydration behavior of nedocromil magnesium pentahydrate

Sodium nitroprusside alters Ca2+ flux components and Ca2(+)‐dependent fluxes of K+ and Cl‐ in rat aorta.

Moisture sorption kinetics for water-soluble substances. II: Experimental verification of heat transport control

Extension of Clausius-Clapeyron equation to predict hydrate stability at different temperatures

Humidity Effect on Diffusion and Structure of a Moisture-Swing CO2 Sorbent

Moisture sorption kinetics for water-soluble substances. III: Theoretical and experimental studies in air

Gas Chromatographic Thermodynamics on Hydration Processes of Magnesium Chloride with Low Water

Water vapor effect on the physico-geometrical reaction pathway and kinetics of the multistep thermal dehydration of calcium chloride dihydrate

Spontaneous Crystalline-to-Amorphous Phase Transformation of Organic or Medicinal Compounds in the Presence of Porous Media, Part 3: Effect of Moisture

Cooperation for secure wireless communications with resource-bounded eavesdroppers

Physico-geometrical reaction pathway and kinetics of multistep thermal dehydration of calcium chloride dihydrate in a dry nitrogen stream

Nucleation kinetics in drying sodium nitrate aerosols

Evolution of Chemical Bonding and Crystalline Swelling-Shrinkage of Montmorillonite upon Temperature Changes Probed by in Situ Fourier Transform Infrared Spectroscopy and X-ray Diffraction

Influence of Temperature on Solvent-Mediated Anhydrate-to-hydrate Transformation Kinetics.

Internal Forces Within the Layered Structure of Na-Montmorillonite Hydrates: Molecular Dynamics Simulation

Tailoring Crystallization Kinetics in Thin Sucrose Films during Convective Drying: Impact of Temperature and Humidity on Onset, Growth, and Nucleation Rate

Nanoscale Ion Dynamics Control on Amorphous Calcium Carbonate Crystallization: Precise Control of Calcite Crystal Sizes

Hyphenation of Raman spectroscopy with gravimetric analysis to interrogate water-solid interactions in pharmaceutical systems

Nanoscale Control Over Water-Film Thickness Using Temperature Modulation: Tuning Mineral Carbonation Reactivity