Abstract:Temperature control is essential for fast-charging performance of Li-ion battery. Cold temperature leads to sluggish ion transportation of electrolyte, brittle polymeric cell components, changes in solid electrolyte interface (SEI) properties and associated resistance build-up, and Li plating and dendrite growth [1]. High temperature boosts fast charging but can also accelerate battery degradation and increase the rise of battery thermal failure. This is caused by the increased rate of side-reactions, resulting in loss of cyclable lithium and higher rate of attrition of active materials at higher temperatures. Temperature and its gradient in a battery unit strongly affect performance and life of battery units [2]. It is recommended that pack temperature uniformity of a li-ion battery pack in electric vehicles shall be less than 3 oC [3]. Battery thermal management systems (BTMS) are important for controlling battery pack temperature and minimizing temperature gradients to prevent thermal-related issues in Battery Energy Storage Systems (BESS). This thermal management goal is more critical for fast charging of battery modules made of large format, high-energy-density cells. Current BTMS in battery electric vehicles (BEVs) are inadequate in limiting the maximum temperature rise of the battery during extreme fast charge (i.e., 6C charge). To achieve fast-charge, the size of the battery thermal management system needs to increase from today's BEV average size of 1–5 kW to around 15–25 kW [4]. A combined experimental and modelling approach is employed to access thermal and electrochemical heterogeneities of a battery module under extreme fast charge conditions and develop corresponding mitigation approaches. The electrochemical-thermal model was built based on electrical characterization of 32 mAh pouch cells, including constant-current 1C to 9C rates of charging at varying temperatures. Predictive performance of the model in heat generation was validated by comparing results against measurements conducted using a microcalorimeter. Thereafter, the validated model is used to predict performance of a battery module consisting of six large format pouch cells. The large pouch cell has a capacity of 25 Ah and the identical electrode design of the 32 mAh cells. 3D simulation results suggest significant temperature and charge differences can be produced. The heterogeneous behavior was enlarged along charging. As shown in Figure 1, it was found that electrodes close to the tabs were preferentially charged. Cell electrochemical heterogeneity can be reduced by reducing cell temperature difference. Two potential solutions are investigated using the developed 3D model, including the enhancement of heat transfer within cells, such as increasing cell thermal conductivities with thicker current collectors, and the optimal design of thermal management systems. The feasibility of state-of-the-art thermal management strategies for fast charging is evaluated, including liquid cooling using cold plate devices and direct liquid cooling. References [1] Pesaran, S. Santhanagopalan, G.H. Kim, Addressing the Impact of Temperature Extremes on Large Format Li-Ion Batteries for Vehicle Applications, 30th International Battery Seminar, Ft. Lauderdale, Florida, 2013. [2] Garimella et. Al., A Critical Review of Thermal Issues in Lithium-Ion Batteries, Journal of The Electrochemical Society, ISSN 1945-7111, 158(3), R1-R25(2011) [3] USABC, Li-Ion Battery Thermal Management System Requirements, 2018 [4] Keyser et. Al., Enabling Fast Charging – Battery Thermal Considerations, Journal of Power Sources, ISSN 0378-7753, 367(2017) 228-236 Figure 1

External Cooling and Degradation Interplay in Lithium-Ion Battery Fast Charging

An Optimal Fast-Charging Strategy for Lithium-Ion Batteries Via an Electrochemical–Thermal Model with Intercalation-Induced Stresses and Film Growth

Effect of High-Temperature Thermal Management on Degradation of Li-ion Battery for Fast Charging

Mitigating Heterogeneities in Lithium-Ion Battery Modules Under Fast Charging

Effect of fast charging on degradation and safety characteristics of lithium-ion batteries with LiFePO 4 cathodes

Lithium-ion battery fast charging: A review

Non-destructive battery fast charging constrained by lithium plating and high temperature limit based on simulation

Effect of thermal environments on fast charging Li-ion batteries

The Effects of Temperature and Cell Parameters on Lithium-Ion Battery Fast Charging Protocols: A Model-Driven Investigation

Revealing the Impact of Fast Charge Cycling on the Thermal Safety of Lithium-Ion Batteries

Multi-objective optimization design and experimental investigation for a parallel liquid cooling-based Lithium-ion battery module under fast charging

A Thermal Design and Experimental Investigation for the Fast Charging Process of a Lithium-Ion Battery Module With Liquid Cooling

Investigation on Lithium-Ion Battery Degradation Induced by Combined Effect of Current Rate and Operating Temperature During Fast Charging

Study on Lithium-Ion Battery Degradation Caused by Side Reactions in Fast-Charging Process

Critical Review on Internal and External Battery Thermal Management Systems for Fast Charging Applications

Toward safe and rapid battery charging: Design optimal fast charging strategies thorough a physics‐based model considering lithium plating

Inhomogeneous Degradation in Lithium-Ion Batteries: The Effect of Thermal Gradients

Challenges and Opportunities Toward Fast-Charging of Lithium-Ion Batteries

Optimisation with adiabatic interlayers for liquid-dominated cooling system on fast charging battery packs

Closed-loop Fast Charging Strategy of Lithium-Ion Batteries Based on Temperature Limitation and Lithium Precipitation

Probing Inhomogeneity of Electrical-Thermal Distribution on Electrode During Fast Charging for Lithium-Ion Batteries